From: Aswath Govindraju <a-govindraju@ti.com>
To: unlisted-recipients:; (no To-header on input)
Cc: Vignesh Raghavendra <vigneshr@ti.com>,
Lokesh Vutla <lokeshvutla@ti.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Jan Kiszka <jan.kiszka@siemens.com>,
Aswath Govindraju <a-govindraju@ti.com>,
Nishanth Menon <nm@ti.com>, Tero Kristo <kristo@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH v2] arm64: dts: ti: k3-am65: Add support for UHS-I modes in MMCSD1 subsystem
Date: Tue, 11 May 2021 15:23:39 +0530 [thread overview]
Message-ID: <20210511095339.16268-1-a-govindraju@ti.com> (raw)
UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1].
Add support by removing the no-1-8-v tag and including the voltage
regulator device tree nodes for power cycling.
However, the 4 bit interface of AM65 SR 1.0 cannot be supported at 3.3 V or
1.8 V because of erratas i2025 and i2026 [2]. As the SD card is the primary
boot mode for development usecases, continue to enable SD card and disable
UHS-I modes in it to minimize any ageing issues happening because of
erratas.
k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards use S.R. 1.0
version of AM65 SoC. Therefore, add no-1-8-v in sdhci1 device tree nodes
for these boards.
[1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1
[2] - https://www.ti.com/lit/er/sprz452e/sprz452e.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 1 -
.../boot/dts/ti/k3-am6528-iot2050-basic.dts | 4 +++
.../arm64/boot/dts/ti/k3-am654-base-board.dts | 33 +++++++++++++++++++
.../dts/ti/k3-am6548-iot2050-advanced.dts | 4 +++
4 files changed, 41 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index cb340d1b401f..632f32fce4a1 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -301,7 +301,6 @@
ti,otap-del-sel = <0x2>;
ti,trm-icp = <0x8>;
dma-coherent;
- no-1-8-v;
};
scm_conf: scm-conf@100000 {
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
index 4f7e3f2a6265..485266960d5f 100644
--- a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
@@ -40,6 +40,10 @@
status = "disabled";
};
+&sdhci1 {
+ no-1-8-v;
+};
+
&main_pmx0 {
main_uart0_pins_default: main-uart0-pins-default {
pinctrl-single,pins = <
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 9e87fb313a54..51c594b4dddb 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -91,6 +91,38 @@
#clock-cells = <0>;
clock-frequency = <24000000>;
};
+
+ evm_12v0: fixedregulator-evm12v0 {
+ /* main supply */
+ compatible = "regulator-fixed";
+ regulator-name = "evm_12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc3v3_io: fixedregulator-vcc3v3io {
+ /* Output of TPS54334 */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&evm_12v0>;
+ };
+
+ vdd_mmc1_sd: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vcc3v3_io>;
+ gpio = <&pca9554 4 GPIO_ACTIVE_HIGH>;
+ };
};
&wkup_pmx0 {
@@ -350,6 +382,7 @@
* disable sdhci1
*/
&sdhci1 {
+ vmmc-supply = <&vdd_mmc1_sd>;
pinctrl-names = "default";
pinctrl-0 = <&main_mmc1_pins_default>;
ti,driver-strength-ohm = <50>;
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
index ec9617c13cdb..3643a19b5f33 100644
--- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
@@ -55,6 +55,10 @@
disable-wp;
};
+&sdhci1 {
+ no-1-8-v;
+};
+
&main_uart0 {
status = "disabled";
};
--
2.17.1
next reply other threads:[~2021-05-11 9:54 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-11 9:53 Aswath Govindraju [this message]
2021-05-11 9:55 ` [PATCH v2] arm64: dts: ti: k3-am65: Add support for UHS-I modes in MMCSD1 subsystem Aswath Govindraju
2021-05-11 10:01 ` Jan Kiszka
2021-05-11 10:13 ` Aswath Govindraju
2021-05-11 15:26 ` Jan Kiszka
2021-05-11 16:33 ` Nishanth Menon
2021-05-11 16:40 ` Aswath Govindraju
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210511095339.16268-1-a-govindraju@ti.com \
--to=a-govindraju@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=jan.kiszka@siemens.com \
--cc=kishon@ti.com \
--cc=kristo@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lokeshvutla@ti.com \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).