* [PATCH 00/17] CAMSS: SM8250 support (and some fixes)
@ 2021-05-11 18:07 Jonathan Marek
2021-05-11 18:07 ` [PATCH 17/17] media: dt-bindings: media: camss: Add qcom,sm8250-camss binding Jonathan Marek
0 siblings, 1 reply; 5+ messages in thread
From: Jonathan Marek @ 2021-05-11 18:07 UTC (permalink / raw)
To: linux-arm-msm
Cc: robert.foss, andrey.konovalov, Andy Gross, Bjorn Andersson,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Hans Verkuil, open list,
open list:QUALCOMM CAMERA SUBSYSTEM DRIVER, Mauro Carvalho Chehab,
Rob Herring, Todor Tomov
This adds initial support for SM8250 and its 4 VFEs and 6 CSIPHYs.
The only big change is the added camss-vfe-480.c to support the
Titan 480 VFE.
Jonathan Marek (17):
media: camss: csiphy-3ph: don't print HW version as an error
media: camss: csiphy-3ph: disable interrupts
media: camss: csiphy-3ph: add support for SM8250 CSI DPHY
media: camss: csid-170: fix non-10bit formats
media: camss: csid-170: don't enable unused irqs
media: camss: csid-170: remove stray comment
media: camss: csid-170: support more than one lite vfe
media: camss: csid-170: set the right HALF_CMD when disabled
media: camss: csid: allow csid to work without a regulator
media: camss: remove vdda-csiN from sdm845 resources
media: camss: fix VFE irq name
media: camss: vfe-170: clean up some dead code
media: camss: vfe-170: fix "VFE halt timeout" error
media: camss: Add initial support for VFE hardware version Titan 480
media: camss: add support for V4L2_PIX_FMT_GREY for sdm845 HW
media: camss: add support for SM8250 camss
media: dt-bindings: media: camss: Add qcom,sm8250-camss binding
.../bindings/media/qcom,sm8250-camss.yaml | 398 +++++++++++++
drivers/media/platform/qcom/camss/Makefile | 1 +
.../platform/qcom/camss/camss-csid-170.c | 31 +-
.../media/platform/qcom/camss/camss-csid.c | 39 +-
.../qcom/camss/camss-csiphy-3ph-1-0.c | 181 ++++--
.../media/platform/qcom/camss/camss-csiphy.c | 9 +-
.../media/platform/qcom/camss/camss-vfe-170.c | 65 +-
.../media/platform/qcom/camss/camss-vfe-480.c | 554 ++++++++++++++++++
drivers/media/platform/qcom/camss/camss-vfe.c | 13 +-
drivers/media/platform/qcom/camss/camss-vfe.h | 1 +
.../media/platform/qcom/camss/camss-video.c | 5 +-
drivers/media/platform/qcom/camss/camss.c | 202 ++++++-
drivers/media/platform/qcom/camss/camss.h | 1 +
13 files changed, 1352 insertions(+), 148 deletions(-)
create mode 100644 Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml
create mode 100644 drivers/media/platform/qcom/camss/camss-vfe-480.c
--
2.26.1
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 17/17] media: dt-bindings: media: camss: Add qcom,sm8250-camss binding
2021-05-11 18:07 [PATCH 00/17] CAMSS: SM8250 support (and some fixes) Jonathan Marek
@ 2021-05-11 18:07 ` Jonathan Marek
2021-05-12 18:35 ` Rob Herring
0 siblings, 1 reply; 5+ messages in thread
From: Jonathan Marek @ 2021-05-11 18:07 UTC (permalink / raw)
To: linux-arm-msm
Cc: robert.foss, andrey.konovalov, Andy Gross, Bjorn Andersson,
Todor Tomov, Mauro Carvalho Chehab, Rob Herring,
open list:QUALCOMM CAMERA SUBSYSTEM DRIVER,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
open list
Add bindings for qcom,sm8250-camss in order to support the camera
subsystem for SM8250.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
.../bindings/media/qcom,sm8250-camss.yaml | 398 ++++++++++++++++++
1 file changed, 398 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml
diff --git a/Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml
new file mode 100644
index 000000000000..9a7896d3d9ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml
@@ -0,0 +1,398 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/media/qcom,sm8250-camss.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm CAMSS ISP
+
+maintainers:
+ - Robert Foss <robert.foss@linaro.org>
+
+description: |
+ The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms
+
+properties:
+ compatible:
+ const: qcom,sm8250-camss
+
+ clocks:
+ minItems: 30
+ maxItems: 30
+
+ clock-names:
+ items:
+ - const: cam_hf_axi
+ - const: csiphy0
+ - const: csiphy0_timer
+ - const: csiphy1
+ - const: csiphy1_timer
+ - const: csiphy2
+ - const: csiphy2_timer
+ - const: csiphy3
+ - const: csiphy3_timer
+ - const: csiphy4
+ - const: csiphy4_timer
+ - const: csiphy5
+ - const: csiphy5_timer
+ - const: vfe0_ahb
+ - const: vfe0_axi
+ - const: vfe0
+ - const: vfe0_cphy_rx
+ - const: vfe0_csid
+ - const: vfe0_areg
+ - const: vfe1_ahb
+ - const: vfe1_axi
+ - const: vfe1
+ - const: vfe1_cphy_rx
+ - const: vfe1_csid
+ - const: vfe1_areg
+ - const: vfe_lite_ahb
+ - const: vfe_lite_axi
+ - const: vfe_lite
+ - const: vfe_lite_cphy_rx
+ - const: vfe_lite_csid
+
+ interrupts:
+ minItems: 14
+ maxItems: 14
+
+ interrupt-names:
+ items:
+ - const: csid0
+ - const: csid1
+ - const: csid2
+ - const: csid3
+ - const: csiphy0
+ - const: csiphy1
+ - const: csiphy2
+ - const: csiphy3
+ - const: csiphy4
+ - const: csiphy5
+ - const: vfe0
+ - const: vfe1
+ - const: vfe_lite0
+ - const: vfe_lite1
+
+ iommus:
+ maxItems: 1
+
+ power-domains:
+ items:
+ - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller.
+ - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller.
+ - description: Titan GDSC - Titan ISP Block, Global Distributed Switch Controller.
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ description:
+ CSI input ports.
+
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ Input port for receiving CSI data.
+
+ properties:
+ endpoint:
+ $ref: video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ clock-lanes:
+ maxItems: 1
+
+ data-lanes:
+ minItems: 1
+ maxItems: 4
+
+ required:
+ - clock-lanes
+ - data-lanes
+
+ port@1:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ Input port for receiving CSI data.
+
+ properties:
+ endpoint:
+ $ref: video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ clock-lanes:
+ maxItems: 1
+
+ data-lanes:
+ minItems: 1
+ maxItems: 4
+
+ required:
+ - clock-lanes
+ - data-lanes
+
+ port@2:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ Input port for receiving CSI data.
+
+ properties:
+ endpoint:
+ $ref: video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ clock-lanes:
+ maxItems: 1
+
+ data-lanes:
+ minItems: 1
+ maxItems: 4
+
+ required:
+ - clock-lanes
+ - data-lanes
+
+ port@3:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ Input port for receiving CSI data.
+
+ properties:
+ endpoint:
+ $ref: video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ clock-lanes:
+ maxItems: 1
+
+ data-lanes:
+ minItems: 1
+ maxItems: 4
+
+ required:
+ - clock-lanes
+ - data-lanes
+
+ port@4:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ Input port for receiving CSI data.
+
+ properties:
+ endpoint:
+ $ref: video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ clock-lanes:
+ maxItems: 1
+
+ data-lanes:
+ minItems: 1
+ maxItems: 4
+
+ required:
+ - clock-lanes
+ - data-lanes
+
+ port@5:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ Input port for receiving CSI data.
+
+ properties:
+ endpoint:
+ $ref: video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ clock-lanes:
+ maxItems: 1
+
+ data-lanes:
+ minItems: 1
+ maxItems: 4
+
+ required:
+ - clock-lanes
+ - data-lanes
+
+ reg:
+ minItems: 10
+ maxItems: 10
+
+ reg-names:
+ items:
+ - const: csiphy0
+ - const: csiphy1
+ - const: csiphy2
+ - const: csiphy3
+ - const: csiphy4
+ - const: csiphy5
+ - const: vfe0
+ - const: vfe1
+ - const: vfe_lite0
+ - const: vfe_lite1
+
+required:
+ - clock-names
+ - clocks
+ - compatible
+ - interrupt-names
+ - interrupts
+ - iommus
+ - power-domains
+ - reg
+ - reg-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/qcom,camcc-sm8250.h>
+ #include <dt-bindings/clock/qcom,gcc-sm8250.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ camss: camss@ac6a000 {
+ compatible = "qcom,sm8250-camss";
+
+ reg = <0 0xac6a000 0 0x2000>,
+ <0 0xac6c000 0 0x2000>,
+ <0 0xac6e000 0 0x1000>,
+ <0 0xac70000 0 0x1000>,
+ <0 0xac72000 0 0x1000>,
+ <0 0xac74000 0 0x1000>,
+ <0 0xacb4000 0 0xd000>,
+ <0 0xacc3000 0 0xd000>,
+ <0 0xacd9000 0 0x2200>,
+ <0 0xacdb200 0 0x2200>;
+ reg-names = "csiphy0",
+ "csiphy1",
+ "csiphy2",
+ "csiphy3",
+ "csiphy4",
+ "csiphy5",
+ "vfe0",
+ "vfe1",
+ "vfe_lite0",
+ "vfe_lite1";
+
+ interrupts = <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "csiphy0",
+ "csiphy1",
+ "csiphy2",
+ "csiphy3",
+ "csiphy4",
+ "csiphy5",
+ "csid0",
+ "csid1",
+ "csid2",
+ "csid3",
+ "vfe0",
+ "vfe1",
+ "vfe_lite0",
+ "vfe_lite1";
+
+ power-domains = <&camcc IFE_0_GDSC>,
+ <&camcc IFE_1_GDSC>,
+ <&camcc TITAN_TOP_GDSC>;
+
+ clocks = <&gcc GCC_CAMERA_HF_AXI_CLK>,
+ <&camcc CAM_CC_CSIPHY0_CLK>,
+ <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+ <&camcc CAM_CC_CSIPHY1_CLK>,
+ <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+ <&camcc CAM_CC_CSIPHY2_CLK>,
+ <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+ <&camcc CAM_CC_CSIPHY3_CLK>,
+ <&camcc CAM_CC_CSI3PHYTIMER_CLK>,
+ <&camcc CAM_CC_CSIPHY4_CLK>,
+ <&camcc CAM_CC_CSI4PHYTIMER_CLK>,
+ <&camcc CAM_CC_CSIPHY5_CLK>,
+ <&camcc CAM_CC_CSI5PHYTIMER_CLK>,
+ <&camcc CAM_CC_IFE_0_AHB_CLK>,
+ <&camcc CAM_CC_IFE_0_AXI_CLK>,
+ <&camcc CAM_CC_IFE_0_CLK>,
+ <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
+ <&camcc CAM_CC_IFE_0_CSID_CLK>,
+ <&camcc CAM_CC_IFE_0_AREG_CLK>,
+ <&camcc CAM_CC_IFE_1_AHB_CLK>,
+ <&camcc CAM_CC_IFE_1_AXI_CLK>,
+ <&camcc CAM_CC_IFE_1_CLK>,
+ <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
+ <&camcc CAM_CC_IFE_1_CSID_CLK>,
+ <&camcc CAM_CC_IFE_1_AREG_CLK>,
+ <&camcc CAM_CC_IFE_LITE_AHB_CLK>,
+ <&camcc CAM_CC_IFE_LITE_AXI_CLK>,
+ <&camcc CAM_CC_IFE_LITE_CLK>,
+ <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>,
+ <&camcc CAM_CC_IFE_LITE_CSID_CLK>;
+
+ clock-names = "cam_hf_axi",
+ "csiphy0",
+ "csiphy0_timer",
+ "csiphy1",
+ "csiphy1_timer",
+ "csiphy2",
+ "csiphy2_timer",
+ "csiphy3",
+ "csiphy3_timer",
+ "csiphy4",
+ "csiphy4_timer",
+ "csiphy5",
+ "csiphy5_timer",
+ "vfe0_ahb",
+ "vfe0_axi",
+ "vfe0",
+ "vfe0_cphy_rx",
+ "vfe0_csid",
+ "vfe0_areg",
+ "vfe1_ahb",
+ "vfe1_axi",
+ "vfe1",
+ "vfe1_cphy_rx",
+ "vfe1_csid",
+ "vfe1_areg",
+ "vfe_lite_ahb",
+ "vfe_lite_axi",
+ "vfe_lite",
+ "vfe_lite_cphy_rx",
+ "vfe_lite_csid";
+
+ iommus = <&apps_smmu 0x800 0x400>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
--
2.26.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 17/17] media: dt-bindings: media: camss: Add qcom,sm8250-camss binding
2021-05-11 18:07 ` [PATCH 17/17] media: dt-bindings: media: camss: Add qcom,sm8250-camss binding Jonathan Marek
@ 2021-05-12 18:35 ` Rob Herring
0 siblings, 0 replies; 5+ messages in thread
From: Rob Herring @ 2021-05-12 18:35 UTC (permalink / raw)
To: Jonathan Marek
Cc: devicetree, linux-kernel, Andy Gross, Rob Herring,
andrey.konovalov, linux-arm-msm, linux-media,
Mauro Carvalho Chehab, Todor Tomov, robert.foss, Bjorn Andersson
On Tue, 11 May 2021 14:07:24 -0400, Jonathan Marek wrote:
> Add bindings for qcom,sm8250-camss in order to support the camera
> subsystem for SM8250.
>
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---
> .../bindings/media/qcom,sm8250-camss.yaml | 398 ++++++++++++++++++
> 1 file changed, 398 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/media/qcom,sm8250-camss.example.dts:20:18: fatal error: dt-bindings/clock/qcom,camcc-sm8250.h: No such file or directory
20 | #include <dt-bindings/clock/qcom,camcc-sm8250.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
make[1]: *** [scripts/Makefile.lib:380: Documentation/devicetree/bindings/media/qcom,sm8250-camss.example.dt.yaml] Error 1
make[1]: *** Waiting for unfinished jobs....
make: *** [Makefile:1416: dt_binding_check] Error 2
See https://patchwork.ozlabs.org/patch/1477274
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 00/17] CAMSS: SM8250 support (and some fixes)
@ 2021-06-08 22:34 Jonathan Marek
2021-06-16 18:16 ` Andrey Konovalov
0 siblings, 1 reply; 5+ messages in thread
From: Jonathan Marek @ 2021-06-08 22:34 UTC (permalink / raw)
To: linux-arm-msm
Cc: robert.foss, andrey.konovalov, Andy Gross, Bjorn Andersson,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Hans Verkuil, open list,
open list:QUALCOMM CAMERA SUBSYSTEM DRIVER, Mauro Carvalho Chehab,
Rob Herring, Todor Tomov
This adds initial support for SM8250 and its 4 VFEs and 6 CSIPHYs.
The only big change is the added camss-vfe-480.c to support the
Titan 480 VFE.
v2:
- Fixed some typos in commit messages (patches 02 and 08)
- patch 03 ("media: camss: csiphy-3ph: add support for SM8250 CSI DPHY"):
- moved definition of CAMSS_8250 to this patch,
- removed unused lane_enable variable
- added a default unreachable case to avoid a warning
- added a is_gen2 variable (minor rework)
- Undo DECODE_FORMAT_PAYLOAD_ONLY change, add comment instead (patch 04)
- "ops" reworks in addition to removing dead code (patch 12)
- renamed csid-170 to csid-gen2, added defines for offsets, add missing
camnoc_axi clock to sm8250 vfe resources (patch 16/17)
Jonathan Marek (17):
media: camss: csiphy-3ph: don't print HW version as an error
media: camss: csiphy-3ph: disable interrupts
media: camss: csiphy-3ph: add support for SM8250 CSI DPHY
media: camss: csid-170: fix non-10bit formats
media: camss: csid-170: don't enable unused irqs
media: camss: csid-170: remove stray comment
media: camss: csid-170: support more than one lite vfe
media: camss: csid-170: set the right HALT_CMD when disabled
media: camss: csid: allow csid to work without a regulator
media: camss: remove vdda-csiN from sdm845 resources
media: camss: fix VFE irq name
media: camss: remove some vfe ops and clean up dead vfe-170 code
media: camss: vfe-170: fix "VFE halt timeout" error
media: camss: Add initial support for VFE hardware version Titan 480
media: camss: add support for V4L2_PIX_FMT_GREY for sdm845 HW
media: camss: add support for SM8250 camss
media: dt-bindings: media: camss: Add qcom,sm8250-camss binding
.../bindings/media/qcom,sm8250-camss.yaml | 399 +++++++++++++
drivers/media/platform/qcom/camss/Makefile | 3 +-
.../{camss-csid-170.c => camss-csid-gen2.c} | 32 +-
.../media/platform/qcom/camss/camss-csid.c | 45 +-
.../media/platform/qcom/camss/camss-csid.h | 2 +-
.../qcom/camss/camss-csiphy-3ph-1-0.c | 184 ++++--
.../media/platform/qcom/camss/camss-csiphy.c | 9 +-
.../media/platform/qcom/camss/camss-vfe-170.c | 101 +---
.../media/platform/qcom/camss/camss-vfe-4-1.c | 25 +-
.../media/platform/qcom/camss/camss-vfe-4-7.c | 63 +-
.../media/platform/qcom/camss/camss-vfe-4-8.c | 65 +--
.../media/platform/qcom/camss/camss-vfe-480.c | 545 ++++++++++++++++++
.../platform/qcom/camss/camss-vfe-gen1.c | 94 +--
.../platform/qcom/camss/camss-vfe-gen1.h | 39 +-
drivers/media/platform/qcom/camss/camss-vfe.c | 29 +-
drivers/media/platform/qcom/camss/camss-vfe.h | 17 +-
.../media/platform/qcom/camss/camss-video.c | 5 +-
drivers/media/platform/qcom/camss/camss.c | 205 ++++++-
drivers/media/platform/qcom/camss/camss.h | 1 +
19 files changed, 1523 insertions(+), 340 deletions(-)
create mode 100644 Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml
rename drivers/media/platform/qcom/camss/{camss-csid-170.c => camss-csid-gen2.c} (95%)
create mode 100644 drivers/media/platform/qcom/camss/camss-vfe-480.c
--
2.26.1
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 00/17] CAMSS: SM8250 support (and some fixes)
2021-06-08 22:34 [PATCH 00/17] CAMSS: SM8250 support (and some fixes) Jonathan Marek
@ 2021-06-16 18:16 ` Andrey Konovalov
0 siblings, 0 replies; 5+ messages in thread
From: Andrey Konovalov @ 2021-06-16 18:16 UTC (permalink / raw)
To: Jonathan Marek, linux-arm-msm
Cc: robert.foss, Andy Gross, Bjorn Andersson,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Hans Verkuil, open list,
open list:QUALCOMM CAMERA SUBSYSTEM DRIVER, Mauro Carvalho Chehab,
Rob Herring, Todor Tomov
Hi Jonathan,
I've given this patchset a try on RB3 board (SDM845) with ov8856 camera sensor - works OK,
no regressions.
Thanks,
Andrey
On 09.06.2021 01:34, Jonathan Marek wrote:
> This adds initial support for SM8250 and its 4 VFEs and 6 CSIPHYs.
> The only big change is the added camss-vfe-480.c to support the
> Titan 480 VFE.
>
> v2:
> - Fixed some typos in commit messages (patches 02 and 08)
> - patch 03 ("media: camss: csiphy-3ph: add support for SM8250 CSI DPHY"):
> - moved definition of CAMSS_8250 to this patch,
> - removed unused lane_enable variable
> - added a default unreachable case to avoid a warning
> - added a is_gen2 variable (minor rework)
> - Undo DECODE_FORMAT_PAYLOAD_ONLY change, add comment instead (patch 04)
> - "ops" reworks in addition to removing dead code (patch 12)
> - renamed csid-170 to csid-gen2, added defines for offsets, add missing
> camnoc_axi clock to sm8250 vfe resources (patch 16/17)
>
> Jonathan Marek (17):
> media: camss: csiphy-3ph: don't print HW version as an error
> media: camss: csiphy-3ph: disable interrupts
> media: camss: csiphy-3ph: add support for SM8250 CSI DPHY
> media: camss: csid-170: fix non-10bit formats
> media: camss: csid-170: don't enable unused irqs
> media: camss: csid-170: remove stray comment
> media: camss: csid-170: support more than one lite vfe
> media: camss: csid-170: set the right HALT_CMD when disabled
> media: camss: csid: allow csid to work without a regulator
> media: camss: remove vdda-csiN from sdm845 resources
> media: camss: fix VFE irq name
> media: camss: remove some vfe ops and clean up dead vfe-170 code
> media: camss: vfe-170: fix "VFE halt timeout" error
> media: camss: Add initial support for VFE hardware version Titan 480
> media: camss: add support for V4L2_PIX_FMT_GREY for sdm845 HW
> media: camss: add support for SM8250 camss
> media: dt-bindings: media: camss: Add qcom,sm8250-camss binding
>
> .../bindings/media/qcom,sm8250-camss.yaml | 399 +++++++++++++
> drivers/media/platform/qcom/camss/Makefile | 3 +-
> .../{camss-csid-170.c => camss-csid-gen2.c} | 32 +-
> .../media/platform/qcom/camss/camss-csid.c | 45 +-
> .../media/platform/qcom/camss/camss-csid.h | 2 +-
> .../qcom/camss/camss-csiphy-3ph-1-0.c | 184 ++++--
> .../media/platform/qcom/camss/camss-csiphy.c | 9 +-
> .../media/platform/qcom/camss/camss-vfe-170.c | 101 +---
> .../media/platform/qcom/camss/camss-vfe-4-1.c | 25 +-
> .../media/platform/qcom/camss/camss-vfe-4-7.c | 63 +-
> .../media/platform/qcom/camss/camss-vfe-4-8.c | 65 +--
> .../media/platform/qcom/camss/camss-vfe-480.c | 545 ++++++++++++++++++
> .../platform/qcom/camss/camss-vfe-gen1.c | 94 +--
> .../platform/qcom/camss/camss-vfe-gen1.h | 39 +-
> drivers/media/platform/qcom/camss/camss-vfe.c | 29 +-
> drivers/media/platform/qcom/camss/camss-vfe.h | 17 +-
> .../media/platform/qcom/camss/camss-video.c | 5 +-
> drivers/media/platform/qcom/camss/camss.c | 205 ++++++-
> drivers/media/platform/qcom/camss/camss.h | 1 +
> 19 files changed, 1523 insertions(+), 340 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml
> rename drivers/media/platform/qcom/camss/{camss-csid-170.c => camss-csid-gen2.c} (95%)
> create mode 100644 drivers/media/platform/qcom/camss/camss-vfe-480.c
>
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2021-06-16 18:16 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2021-05-11 18:07 [PATCH 00/17] CAMSS: SM8250 support (and some fixes) Jonathan Marek
2021-05-11 18:07 ` [PATCH 17/17] media: dt-bindings: media: camss: Add qcom,sm8250-camss binding Jonathan Marek
2021-05-12 18:35 ` Rob Herring
-- strict thread matches above, loose matches on Subject: below --
2021-06-08 22:34 [PATCH 00/17] CAMSS: SM8250 support (and some fixes) Jonathan Marek
2021-06-16 18:16 ` Andrey Konovalov
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).