[PATCH v3 1/4] dt-bindings: Add Rockchip rk817 battery charger support

[Chris Morgan <macroalpha82@gmail.com>]

From: Chris Morgan <macromorgan@hotmail.com>

Create dt-binding documentation to document rk817 battery and charger
usage. New device-tree properties have been added.

- rockchip,resistor-sense-micro-ohms: The value in microohms of the
				      sample resistor.
- rockchip,sleep-enter-current-microamp: The value in microamps of the
					 sleep enter current.
- rockchip,sleep-filter-current: The value in microamps of the sleep
				 filter current.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Maya Matuszczyk <maccraft123mc@gmail.com>
---
 .../devicetree/bindings/mfd/rk808.txt         | 36 ++++++++++++++++++-
 1 file changed, 35 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
index 23a17a6663ec..89b9fa7e10b5 100644
--- a/Documentation/devicetree/bindings/mfd/rk808.txt
+++ b/Documentation/devicetree/bindings/mfd/rk808.txt
@@ -70,13 +70,40 @@ Optional RK817 properties:
 
 - vcc8-supply:  The input supply for BOOST
 - vcc9-supply:  The input supply for OTG_SWITCH
+
 - codec:	The child node for the codec to hold additional properties.
 		If no additional properties are required for the codec, this
 		node can be omitted.
-
 - rockchip,mic-in-differential: Telling if the microphone uses differential
 				mode. Should be under the codec child node.
 
+- battery:	The child node for the charger to hold additional properties.
+		If a battery is not in use, this node can be omitted. If a
+		battery node is used, the following values are required:
+		rockchip,resistor-sense, rockchip,sleep-enter-current,
+		rockchip,sleep-filter-current, and a phandle to a
+		monitored-battery node that contains a valid value for
+		charge-full-design-microamp-hours,
+		charge-term-current-microamp,
+		constant-charge-current-max-microamp,
+		constant-charge-voltage-max-microvolt,
+		voltage-max-design-microvolt, voltage-min-design-microvolt,
+		and a valid ocv-capacity table.
+- rockchip,resistor-sense-micro-ohms: Value in microohms of the battery sense
+				      resistor. The PMIC only supports values
+				      of either 10000 or 20000. This value is
+				      used by the driver to set the correct
+				      divisor value to translate ADC readings
+				      into the proper units of measure.
+- rockchip,sleep-enter-current-microamp: Value in microamps of the sleep enter
+					 current for the charger. Value is used
+					 by the driver to calibrate the relax
+					 threshold.
+- rockchip,sleep-filter-current-microamp: Value in microamps of the sleep
+					  filter current for the charger.
+					  Value is used by the driver to derive
+					  the sleep sample current.
+
 Optional RK818 properties:
 - vcc1-supply:  The input supply for DCDC_REG1
 - vcc2-supply:  The input supply for DCDC_REG2
@@ -459,6 +486,13 @@ Example:
 			};
 		};
 
+		rk817_battery: battery {
+			monitored-battery = <&battery_cell>;
+			rockchip,resistor-sense-micro-ohms = <10000>;
+			rockchip,sleep-enter-current-microamp = <300000>;
+			rockchip,sleep-filter-current-microamp = <100000>;
+		};
+
 		rk817_codec: codec {
 			rockchip,mic-in-differential;
 		};
-- 
2.25.1