[PATCH v2 1/3] dt-bindings: iio: chemical: Document senseair,sunrise CO2 sensor

[PATCH v2 1/3] dt-bindings: iio: chemical: Document senseair,sunrise CO2 sensor

[Jacopo Mondi]

Add documentation for the Senseair Sunrise 006-0-0007 CO2 NDIR sensor.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
---
v1->v2:
- Add maxItems to -gpios properties as suggested by Rob
- Add a label to the device node in the example as suggested by Rob

---
 .../iio/chemical/senseair,sunrise.yaml        | 53 +++++++++++++++++++
 .../devicetree/bindings/vendor-prefixes.yaml  |  2 +
 2 files changed, 55 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.yaml

diff --git a/Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.yaml b/Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.yaml
new file mode 100644
index 000000000000..d776adcb0117
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/chemical/senseair,sunrise.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Senseair Sunrise 006-0-0007 CO2 Sensor
+
+maintainers:
+  - Jacopo Mondi <jacopo@jmondi.org>
+
+description: |
+  Senseair Sunrise 006-0-0007 is a NDIR CO2 sensor. It supports I2C or UART buses
+  for communications and control.
+
+  Datasheets:
+    https://rmtplusstoragesenseair.blob.core.windows.net/docs/Dev/publicerat/PSP11704.pdf
+    https://rmtplusstoragesenseair.blob.core.windows.net/docs/Dev/publicerat/PSH11649.pdf
+    https://rmtplusstoragesenseair.blob.core.windows.net/docs/Dev/publicerat/TDE5531.pdf
+    https://rmtplusstoragesenseair.blob.core.windows.net/docs/Market/publicerat/TDE7318.pdf
+
+properties:
+  compatible:
+    const: senseair,sunrise-006-0-0007
+
+  reg:
+    maxItems: 1
+
+  ndry-gpios:
+    maxItems: 1
+    description: Phandle to the GPIO line connected to the nDRY pin. Active low.
+
+  en-gpios:
+    maxItems: 1
+    description: Phandle to the GPIO line connected to the EN pin. Active high.
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      co2-sensor: sunrise@68 {
+        compatible = "senseair,sunrise-006-0-0007";
+        reg = <0x68>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 944a14926e02..c60502eb3d36 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1000,6 +1000,8 @@ patternProperties:
     description: Shenzhen SEI Robotics Co., Ltd
   "^semtech,.*":
     description: Semtech Corporation
+  "^senseair,.*":
+    description: Senseair AB
   "^sensirion,.*":
     description: Sensirion AG
   "^sensortek,.*":
--
2.32.0

Re: [PATCH v2 1/3] dt-bindings: iio: chemical: Document senseair,sunrise CO2 sensor

[Andy Shevchenko]

On Fri, Aug 20, 2021 at 4:38 PM Jacopo Mondi <jacopo@jmondi.org> wrote:
>
> Add documentation for the Senseair Sunrise 006-0-0007 CO2 NDIR sensor.

...

> +    description: Phandle to the GPIO line connected to the nDRY pin. Active low.

> +    description: Phandle to the GPIO line connected to the EN pin. Active high.

As Rob suggested, adding the word "typically" would resolve my claim.

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v2 1/3] dt-bindings: iio: chemical: Document senseair,sunrise CO2 sensor

[Rob Herring]

On Fri, 20 Aug 2021 15:38:19 +0200, Jacopo Mondi wrote:
> Add documentation for the Senseair Sunrise 006-0-0007 CO2 NDIR sensor.
> 
> Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
> ---
> v1->v2:
> - Add maxItems to -gpios properties as suggested by Rob
> - Add a label to the device node in the example as suggested by Rob
> 
> ---
>  .../iio/chemical/senseair,sunrise.yaml        | 53 +++++++++++++++++++
>  .../devicetree/bindings/vendor-prefixes.yaml  |  2 +
>  2 files changed, 55 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
Error: Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.example.dts:23.21-22 syntax error
FATAL ERROR: Unable to parse input tree
make[1]: *** [scripts/Makefile.lib:380: Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.example.dt.yaml] Error 1
make[1]: *** Waiting for unfinished jobs....
make: *** [Makefile:1419: dt_binding_check] Error 2

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/1519042

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.

Re: [PATCH v2 1/3] dt-bindings: iio: chemical: Document senseair,sunrise CO2 sensor

[Jacopo Mondi]

On Fri, Aug 20, 2021 at 02:46:12PM -0500, Rob Herring wrote:
> On Fri, 20 Aug 2021 15:38:19 +0200, Jacopo Mondi wrote:
> > Add documentation for the Senseair Sunrise 006-0-0007 CO2 NDIR sensor.
> >
> > Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
> > ---
> > v1->v2:
> > - Add maxItems to -gpios properties as suggested by Rob
> > - Add a label to the device node in the example as suggested by Rob
> >

Labels cannot contain '-'.

I'll make this

        sunrise: co2-sensor@68

My bad and sorry for not running dt_binding_check, I thought the
changes were trivial enough.

Thanks
   j

> > ---
> >  .../iio/chemical/senseair,sunrise.yaml        | 53 +++++++++++++++++++
> >  .../devicetree/bindings/vendor-prefixes.yaml  |  2 +
> >  2 files changed, 55 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.yaml
> >
>
> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
> on your patch (DT_CHECKER_FLAGS is new in v5.13):
>
> yamllint warnings/errors:
>
> dtschema/dtc warnings/errors:
> Error: Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.example.dts:23.21-22 syntax error
> FATAL ERROR: Unable to parse input tree
> make[1]: *** [scripts/Makefile.lib:380: Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.example.dt.yaml] Error 1
> make[1]: *** Waiting for unfinished jobs....
> make: *** [Makefile:1419: dt_binding_check] Error 2
>
> doc reference errors (make refcheckdocs):
>
> See https://patchwork.ozlabs.org/patch/1519042
>
> This check can fail if there are any dependencies. The base for a patch
> series is generally the most recent rc1.
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure 'yamllint' is installed and dt-schema is up to
> date:
>
> pip3 install dtschema --upgrade
>
> Please check and re-submit.
>

Re: [PATCH v2 1/3] dt-bindings: iio: chemical: Document senseair,sunrise CO2 sensor

[Jonathan Cameron]

On Sun, 22 Aug 2021 18:04:44 +0200
Jacopo Mondi <jacopo@jmondi.org> wrote:

> On Fri, Aug 20, 2021 at 02:46:12PM -0500, Rob Herring wrote:
> > On Fri, 20 Aug 2021 15:38:19 +0200, Jacopo Mondi wrote:  
> > > Add documentation for the Senseair Sunrise 006-0-0007 CO2 NDIR sensor.
> > >
> > > Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
> > > ---
> > > v1->v2:
> > > - Add maxItems to -gpios properties as suggested by Rob
> > > - Add a label to the device node in the example as suggested by Rob
> > >  
> 
> Labels cannot contain '-'.
> 
> I'll make this
> 
>         sunrise: co2-sensor@68

Why label at all?  Might be handy on a real board, but example doesn't need it.

Jonathan

> 
> My bad and sorry for not running dt_binding_check, I thought the
> changes were trivial enough.
> 
> Thanks
>    j
> 
> > > ---
> > >  .../iio/chemical/senseair,sunrise.yaml        | 53 +++++++++++++++++++
> > >  .../devicetree/bindings/vendor-prefixes.yaml  |  2 +
> > >  2 files changed, 55 insertions(+)
> > >  create mode 100644 Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.yaml
> > >  
> >
> > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
> > on your patch (DT_CHECKER_FLAGS is new in v5.13):
> >
> > yamllint warnings/errors:
> >
> > dtschema/dtc warnings/errors:
> > Error: Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.example.dts:23.21-22 syntax error
> > FATAL ERROR: Unable to parse input tree
> > make[1]: *** [scripts/Makefile.lib:380: Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.example.dt.yaml] Error 1
> > make[1]: *** Waiting for unfinished jobs....
> > make: *** [Makefile:1419: dt_binding_check] Error 2
> >
> > doc reference errors (make refcheckdocs):
> >
> > See https://patchwork.ozlabs.org/patch/1519042
> >
> > This check can fail if there are any dependencies. The base for a patch
> > series is generally the most recent rc1.
> >
> > If you already ran 'make dt_binding_check' and didn't see the above
> > error(s), then make sure 'yamllint' is installed and dt-schema is up to
> > date:
> >
> > pip3 install dtschema --upgrade
> >
> > Please check and re-submit.
> >