* [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit
@ 2021-09-29 8:13 Sinthu Raja
2021-09-29 8:13 ` [PATCH V3 1/4] dt-bindings: arm: ti: Add compatible for J721E SK Sinthu Raja
` (4 more replies)
0 siblings, 5 replies; 7+ messages in thread
From: Sinthu Raja @ 2021-09-29 8:13 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Vignesh Raghavendra, linux-arm-kernel, devicetree, linux-kernel,
Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
Hi,
This series of patches add support for J721e Starter kit(SK)[1]. J721e SK
is a low cost, small form factor board designed for TI’s J721E SoC.
Changes in V3:
- Introduced IPC sub mailbox nodes patch.
- Introduced DDR carveout memory nodes patch.
- Updated board name to starter kit
- Fixed DTS binding errors.
- Updated commit message, $subject which includes adding board URL,
V2: https://lore.kernel.org/all/20210602182237.12632-1-sinthu.raja@ti.com/
V1: https://lore.kernel.org/all/20210602182237.12632-1-sinthu.raja@ti.com/
[1]https://www.ti.com/tool/SK-TDA4VM
Sinthu Raja (4):
dt-bindings: arm: ti: Add compatible for J721E SK
arm64: dts: ti: Add support for J721E SK
arm64: dts: ti: k3-j721e-sk: Add IPC sub-mailbox nodes
arm64: dts: ti: k3-j721e-sk: Add DDR carveout memory nodes
.../devicetree/bindings/arm/ti/k3.yaml | 1 +
arch/arm64/boot/dts/ti/Makefile | 1 +
arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 1002 +++++++++++++++++
3 files changed, 1004 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-sk.dts
--
2.31.1
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH V3 1/4] dt-bindings: arm: ti: Add compatible for J721E SK 2021-09-29 8:13 [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit Sinthu Raja @ 2021-09-29 8:13 ` Sinthu Raja 2021-10-04 18:43 ` Rob Herring 2021-09-29 8:13 ` [PATCH V3 2/4] arm64: dts: ti: Add support " Sinthu Raja ` (3 subsequent siblings) 4 siblings, 1 reply; 7+ messages in thread From: Sinthu Raja @ 2021-09-29 8:13 UTC (permalink / raw) To: Nishanth Menon, Tero Kristo, Rob Herring Cc: Vignesh Raghavendra, linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja From: Sinthu Raja <sinthu.raja@ti.com> J721E Starter Kit (SK)[1] is a low cost, small form factor board designed for TI’s J721E SoC. Add j721e-sk into compatible enum. [1]https://www.ti.com/tool/SK-TDA4VM Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> --- Changes in V3: * Addressed review comments. * Added Board URL to the commit description. V2: https://lore.kernel.org/all/20210607093314.23909-2-sinthu.raja@ti.com/ V1: https://lore.kernel.org/all/20210602182237.12632-2-sinthu.raja@ti.com/ Documentation/devicetree/bindings/arm/ti/k3.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/ti/k3.yaml b/Documentation/devicetree/bindings/arm/ti/k3.yaml index 29ca364e8a76..d97af3f628d8 100644 --- a/Documentation/devicetree/bindings/arm/ti/k3.yaml +++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml @@ -31,6 +31,7 @@ properties: items: - enum: - ti,j721e-evm + - ti,j721e-sk - const: ti,j721e - description: K3 J7200 SoC -- 2.31.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH V3 1/4] dt-bindings: arm: ti: Add compatible for J721E SK 2021-09-29 8:13 ` [PATCH V3 1/4] dt-bindings: arm: ti: Add compatible for J721E SK Sinthu Raja @ 2021-10-04 18:43 ` Rob Herring 0 siblings, 0 replies; 7+ messages in thread From: Rob Herring @ 2021-10-04 18:43 UTC (permalink / raw) To: Sinthu Raja Cc: Sinthu Raja, Rob Herring, Tero Kristo, devicetree, Vignesh Raghavendra, linux-kernel, linux-arm-kernel, Nishanth Menon On Wed, 29 Sep 2021 13:43:30 +0530, Sinthu Raja wrote: > From: Sinthu Raja <sinthu.raja@ti.com> > > J721E Starter Kit (SK)[1] is a low cost, small form factor board > designed for TI’s J721E SoC. Add j721e-sk into compatible enum. > > [1]https://www.ti.com/tool/SK-TDA4VM > > Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> > --- > > Changes in V3: > * Addressed review comments. > * Added Board URL to the commit description. > > V2: https://lore.kernel.org/all/20210607093314.23909-2-sinthu.raja@ti.com/ > V1: https://lore.kernel.org/all/20210602182237.12632-2-sinthu.raja@ti.com/ > > Documentation/devicetree/bindings/arm/ti/k3.yaml | 1 + > 1 file changed, 1 insertion(+) > Acked-by: Rob Herring <robh@kernel.org> ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH V3 2/4] arm64: dts: ti: Add support for J721E SK 2021-09-29 8:13 [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit Sinthu Raja 2021-09-29 8:13 ` [PATCH V3 1/4] dt-bindings: arm: ti: Add compatible for J721E SK Sinthu Raja @ 2021-09-29 8:13 ` Sinthu Raja 2021-09-29 8:13 ` [PATCH V3 3/4] arm64: dts: ti: k3-j721e-sk: Add IPC sub-mailbox nodes Sinthu Raja ` (2 subsequent siblings) 4 siblings, 0 replies; 7+ messages in thread From: Sinthu Raja @ 2021-09-29 8:13 UTC (permalink / raw) To: Nishanth Menon, Tero Kristo, Rob Herring Cc: Vignesh Raghavendra, linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja From: Sinthu Raja <sinthu.raja@ti.com> J721E Starter Kit (SK)[1] is a low cost, small form factor board designed for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high performance vision accelerators, video codec accelerators, latest C71x and C66x DSP, high bandwidth real-time IPs for capture and display, GPU, dedicated safety island and security accelerators. The SoC is power optimized to provide best in class performance for industrial and automotive applications. J721E SK supports the following interfaces: * 4 GB LPDDR4 RAM * x1 Gigabit Ethernet interface * x1 USB 3.0 Type-C port * x3 USB 3.0 Type-A ports * x1 PCIe M.2 E Key * x1 PCIe M.2 M Key * 512 Mbit OSPI flash * x2 CSI2 Camera interface (RPi and TI Camera connector) * 40-pin Raspberry Pi GPIO header Add basic support for J721E-SK. [1] https://www.ti.com/tool/SK-TDA4VM Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> --- Changes in V3: * Addressed review comments. * Included Board URL to the commit description. V2: https://lore.kernel.org/all/20210607093314.23909-3-sinthu.raja@ti.com/ V1: https://lore.kernel.org/all/20210602182237.12632-3-sinthu.raja@ti.com/ arch/arm64/boot/dts/ti/Makefile | 1 + arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 729 +++++++++++++++++++++++++ 2 files changed, 730 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-sk.dts diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile index d56c742f5a10..38fd3967ab04 100644 --- a/arch/arm64/boot/dts/ti/Makefile +++ b/arch/arm64/boot/dts/ti/Makefile @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb +dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb diff --git a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts new file mode 100644 index 000000000000..2ca92ed12f03 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts @@ -0,0 +1,729 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ + * + * J721E SK URL: https://www.ti.com/tool/SK-TDA4VM + */ + +/dts-v1/; + +#include "k3-j721e.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/net/ti-dp83867.h> + +/ { + compatible = "ti,j721e-sk", "ti,j721e"; + model = "Texas Instruments J721E SK"; + + chosen { + stdout-path = "serial2:115200n8"; + bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; + }; + + memory@80000000 { + device_type = "memory"; + /* 4G RAM */ + reg = <0x00000000 0x80000000 0x00000000 0x80000000>, + <0x00000008 0x80000000 0x00000000 0x80000000>; + }; + + vusb_main: fixedregulator-vusb-main5v0 { + /* USB MAIN INPUT 5V DC */ + compatible = "regulator-fixed"; + regulator-name = "vusb-main5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vsys_3v3: fixedregulator-vsys3v3 { + /* Output of LM5141 */ + compatible = "regulator-fixed"; + regulator-name = "vsys_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vusb_main>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_mmc1: fixedregulator-sd { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&vdd_mmc1_en_pins_default>; + regulator-name = "vdd_mmc1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + vin-supply = <&vsys_3v3>; + gpio = <&wkup_gpio0 8 GPIO_ACTIVE_HIGH>; + }; + + vdd_sd_dv_alt: gpio-regulator-tps659411 { + compatible = "regulator-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&vdd_sd_dv_alt_pins_default>; + regulator-name = "tps659411"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + vin-supply = <&vsys_3v3>; + gpios = <&wkup_gpio0 9 GPIO_ACTIVE_HIGH>; + states = <1800000 0x0>, + <3300000 0x1>; + }; + + dp_pwr_3v3: fixedregulator-dp-prw { + compatible = "regulator-fixed"; + regulator-name = "dp-pwr"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&dp_pwr_en_pins_default>; + gpio = <&main_gpio0 111 0>; /* DP0_3V3 _EN */ + enable-active-high; + }; + +}; + +&main_pmx0 { + main_mmc1_pins_default: main-mmc1-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */ + J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */ + J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */ + J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */ + J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */ + J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */ + J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */ + J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */ + >; + }; + + main_uart0_pins_default: main-uart0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x1f0, PIN_INPUT, 0) /* (AC2) UART0_CTSn */ + J721E_IOPAD(0x1f4, PIN_OUTPUT, 0) /* (AB1) UART0_RTSn */ + J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */ + J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */ + >; + }; + + main_i2c0_pins_default: main-i2c0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */ + J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */ + >; + }; + + main_i2c1_pins_default: main-i2c1-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */ + J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */ + >; + }; + + main_i2c3_pins_default: main-i2c3-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */ + J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */ + >; + }; + + main_usbss0_pins_default: main-usbss0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */ + J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */ + >; + }; + + main_usbss1_pins_default: main-usbss1-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */ + >; + }; + + dp0_pins_default: dp0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x1c4, PIN_INPUT, 5) /* SPI0_CS1.DP0_HPD */ + >; + }; + + dp_pwr_en_pins_default: dp-pwr-en-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x1c0, PIN_INPUT, 7) /* (AA2) SPI0_CS0.GPIO0_111 */ + >; + }; + + dss_vout0_pins_default: dss-vout0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x58, PIN_OUTPUT, 10) /* (AE22) PRG1_PRU1_GPO0.VOUT0_DATA0 */ + J721E_IOPAD(0x5c, PIN_OUTPUT, 10) /* (AG23) PRG1_PRU1_GPO1.VOUT0_DATA1 */ + J721E_IOPAD(0x60, PIN_OUTPUT, 10) /* (AF23) PRG1_PRU1_GPO2.VOUT0_DATA2 */ + J721E_IOPAD(0x64, PIN_OUTPUT, 10) /* (AD23) PRG1_PRU1_GPO3.VOUT0_DATA3 */ + J721E_IOPAD(0x68, PIN_OUTPUT, 10) /* (AH24) PRG1_PRU1_GPO4.VOUT0_DATA4 */ + J721E_IOPAD(0x6c, PIN_OUTPUT, 10) /* (AG21) PRG1_PRU1_GPO5.VOUT0_DATA5 */ + J721E_IOPAD(0x70, PIN_OUTPUT, 10) /* (AE23) PRG1_PRU1_GPO6.VOUT0_DATA6 */ + J721E_IOPAD(0x74, PIN_OUTPUT, 10) /* (AC21) PRG1_PRU1_GPO7.VOUT0_DATA7 */ + J721E_IOPAD(0x78, PIN_OUTPUT, 10) /* (Y23) PRG1_PRU1_GPO8.VOUT0_DATA8 */ + J721E_IOPAD(0x7c, PIN_OUTPUT, 10) /* (AF21) PRG1_PRU1_GPO9.VOUT0_DATA9 */ + J721E_IOPAD(0x80, PIN_OUTPUT, 10) /* (AB23) PRG1_PRU1_GPO10.VOUT0_DATA10 */ + J721E_IOPAD(0x84, PIN_OUTPUT, 10) /* (AJ25) PRG1_PRU1_GPO11.VOUT0_DATA11 */ + J721E_IOPAD(0x88, PIN_OUTPUT, 10) /* (AH25) PRG1_PRU1_GPO12.VOUT0_DATA12 */ + J721E_IOPAD(0x8c, PIN_OUTPUT, 10) /* (AG25) PRG1_PRU1_GPO13.VOUT0_DATA13 */ + J721E_IOPAD(0x90, PIN_OUTPUT, 10) /* (AH26) PRG1_PRU1_GPO14.VOUT0_DATA14 */ + J721E_IOPAD(0x94, PIN_OUTPUT, 10) /* (AJ27) PRG1_PRU1_GPO15.VOUT0_DATA15 */ + J721E_IOPAD(0x30, PIN_OUTPUT, 10) /* (AF24) PRG1_PRU0_GPO11.VOUT0_DATA16 */ + J721E_IOPAD(0x34, PIN_OUTPUT, 10) /* (AJ24) PRG1_PRU0_GPO12.VOUT0_DATA17 */ + J721E_IOPAD(0x38, PIN_OUTPUT, 10) /* (AG24) PRG1_PRU0_GPO13.VOUT0_DATA18 */ + J721E_IOPAD(0x3c, PIN_OUTPUT, 10) /* (AD24) PRG1_PRU0_GPO14.VOUT0_DATA19 */ + J721E_IOPAD(0x40, PIN_OUTPUT, 10) /* (AC24) PRG1_PRU0_GPO15.VOUT0_DATA20 */ + J721E_IOPAD(0x44, PIN_OUTPUT, 10) /* (AE24) PRG1_PRU0_GPO16.VOUT0_DATA21 */ + J721E_IOPAD(0x24, PIN_OUTPUT, 10) /* (AJ20) PRG1_PRU0_GPO8.VOUT0_DATA22 */ + J721E_IOPAD(0x28, PIN_OUTPUT, 10) /* (AG20) PRG1_PRU0_GPO9.VOUT0_DATA23 */ + J721E_IOPAD(0x9c, PIN_OUTPUT, 10) /* (AC22) PRG1_PRU1_GPO17.VOUT0_DE */ + J721E_IOPAD(0x98, PIN_OUTPUT, 10) /* (AJ26) PRG1_PRU1_GPO16.VOUT0_HSYNC */ + J721E_IOPAD(0xa4, PIN_OUTPUT, 10) /* (AH22) PRG1_PRU1_GPO19.VOUT0_PCLK */ + J721E_IOPAD(0xa0, PIN_OUTPUT, 10) /* (AJ22) PRG1_PRU1_GPO18.VOUT0_VSYNC */ + >; + }; + + /* Reset for M.2 E Key slot on PCIe0 */ + ekey_reset_pins_default: ekey-reset-pns-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x124, PIN_INPUT, 7) /* (Y24) PRG0_PRU1_GPO9.GPIO0_72 */ + >; + }; +}; + +&wkup_pmx0 { + mcu_cpsw_pins_default: mcu-cpsw-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x84, PIN_INPUT, 0) /* (B24) MCU_RGMII1_RD0 */ + J721E_WKUP_IOPAD(0x80, PIN_INPUT, 0) /* (A24) MCU_RGMII1_RD1 */ + J721E_WKUP_IOPAD(0x7c, PIN_INPUT, 0) /* (D24) MCU_RGMII1_RD2 */ + J721E_WKUP_IOPAD(0x78, PIN_INPUT, 0) /* (A25) MCU_RGMII1_RD3 */ + J721E_WKUP_IOPAD(0x74, PIN_INPUT, 0) /* (C24) MCU_RGMII1_RXC */ + J721E_WKUP_IOPAD(0x5c, PIN_INPUT, 0) /* (C25) MCU_RGMII1_RX_CTL */ + J721E_WKUP_IOPAD(0x6c, PIN_OUTPUT, 0) /* (B25) MCU_RGMII1_TD0 */ + J721E_WKUP_IOPAD(0x68, PIN_OUTPUT, 0) /* (A26) MCU_RGMII1_TD1 */ + J721E_WKUP_IOPAD(0x64, PIN_OUTPUT, 0) /* (A27) MCU_RGMII1_TD2 */ + J721E_WKUP_IOPAD(0x60, PIN_OUTPUT, 0) /* (A28) MCU_RGMII1_TD3 */ + J721E_WKUP_IOPAD(0x70, PIN_OUTPUT, 0) /* (B26) MCU_RGMII1_TXC */ + J721E_WKUP_IOPAD(0x58, PIN_OUTPUT, 0) /* (B27) MCU_RGMII1_TX_CTL */ + >; + }; + + mcu_mdio_pins_default: mcu-mdio1-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x8c, PIN_OUTPUT, 0) /* (F23) MCU_MDIO0_MDC */ + J721E_WKUP_IOPAD(0x88, PIN_INPUT, 0) /* (E23) MCU_MDIO0_MDIO */ + >; + }; + + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 0) /* (E20) MCU_OSPI0_CLK */ + J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 0) /* (F19) MCU_OSPI0_CSn0 */ + J721E_WKUP_IOPAD(0xc, PIN_INPUT, 0) /* (D20) MCU_OSPI0_D0 */ + J721E_WKUP_IOPAD(0x10, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D1 */ + J721E_WKUP_IOPAD(0x14, PIN_INPUT, 0) /* (G20) MCU_OSPI0_D2 */ + J721E_WKUP_IOPAD(0x18, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D3 */ + J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 0) /* (F21) MCU_OSPI0_D4 */ + J721E_WKUP_IOPAD(0x20, PIN_INPUT, 0) /* (E21) MCU_OSPI0_D5 */ + J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */ + J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */ + J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */ + >; + }; + + vdd_mmc1_en_pins_default: vdd-mmc1-en-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xd0, PIN_OUTPUT, 7) /* (G27) WKUP_GPIO0_8 */ + >; + }; + + vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */ + >; + }; + + wkup_i2c0_pins_default: wkup-i2c0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */ + J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */ + >; + }; + + /* Reset for M.2 M Key slot on PCIe1 */ + mkey_reset_pins_default: mkey-reset-pns-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xdc, PIN_INPUT, 7) /* (H27) WKUP_GPIO0_11 */ + >; + }; +}; + +&wkup_uart0 { + /* Wakeup UART is used by System firmware */ + status = "reserved"; +}; + +&main_uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_uart0_pins_default>; + /* Shared with ATF on this platform */ + power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>; +}; + +&main_uart2 { + /* Brought out on RPi header */ + status = "disabled"; +}; + +&main_uart3 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart5 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart6 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart7 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart8 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart9 { + /* Brought out on M.2 E Key */ + status = "disabled"; +}; + +&main_sdhci0 { + /* Unused */ + status = "disabled"; +}; + +&main_sdhci1 { + /* SD Card */ + vmmc-supply = <&vdd_mmc1>; + vqmmc-supply = <&vdd_sd_dv_alt>; + pinctrl-names = "default"; + pinctrl-0 = <&main_mmc1_pins_default>; + ti,driver-strength-ohm = <50>; + disable-wp; +}; + +&main_sdhci2 { + /* Unused */ + status = "disabled"; +}; + +&ospi0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <8>; + spi-rx-bus-width = <8>; + spi-max-frequency = <25000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <4>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&ospi1 { + /* Unused */ + status = "disabled"; +}; + +&main_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + + i2c-mux@71 { + compatible = "nxp,pca9543"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x71>; + + /* PCIe1 M.2 M Key I2C */ + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + /* PCIe0 M.2 E Key I2C */ + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + }; +}; + +&main_i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_pins_default>; + /* i2c1 is used for DVI DDC, so we need to use 100kHz */ + clock-frequency = <100000>; +}; + +&main_i2c2 { + /* Unused */ + status = "disabled"; +}; + +&main_i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c3_pins_default>; + clock-frequency = <400000>; + + i2c-mux@70 { + compatible = "nxp,pca9543"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + /* CSI0 I2C */ + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + /* CSI1 I2C */ + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + }; +}; + +&main_i2c4 { + /* Unused */ + status = "disabled"; +}; + +&main_i2c5 { + /* Brought out on RPi Header */ + status = "disabled"; +}; + +&main_i2c6 { + /* Unused */ + status = "disabled"; +}; + +&main_gpio2 { + status = "disabled"; +}; + +&main_gpio3 { + status = "disabled"; +}; + +&main_gpio4 { + status = "disabled"; +}; + +&main_gpio5 { + status = "disabled"; +}; + +&main_gpio6 { + status = "disabled"; +}; + +&main_gpio7 { + status = "disabled"; +}; + +&wkup_gpio1 { + status = "disabled"; +}; + +&main_r5fss0_core0{ + firmware-name = "pdk-ipc/ipc_echo_test_mcu2_0_release_strip.xer5f"; +}; + +&usb_serdes_mux { + idle-states = <1>, <1>; /* USB0 to SERDES3, USB1 to SERDES2 */ +}; + +&serdes_ln_ctrl { + idle-states = <J721E_SERDES0_LANE0_PCIE0_LANE0>, <J721E_SERDES0_LANE1_IP4_UNUSED>, + <J721E_SERDES1_LANE0_PCIE1_LANE0>, <J721E_SERDES1_LANE1_PCIE1_LANE1>, + <J721E_SERDES2_LANE0_IP1_UNUSED>, <J721E_SERDES2_LANE1_USB3_1>, + <J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>, + <J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>, + <J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>; +}; + +&serdes_wiz3 { + typec-dir-gpios = <&main_gpio1 3 GPIO_ACTIVE_HIGH>; + typec-dir-debounce-ms = <700>; /* TUSB321, tCCB_DEFAULT 133 ms */ +}; + +&serdes3 { + serdes3_usb_link: phy@0 { + reg = <0>; + cdns,num-lanes = <2>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_USB3>; + resets = <&serdes_wiz3 1>, <&serdes_wiz3 2>; + }; +}; + +&usbss0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_usbss0_pins_default>; + ti,vbus-divider; +}; + +&usb0 { + dr_mode = "otg"; + maximum-speed = "super-speed"; + phys = <&serdes3_usb_link>; + phy-names = "cdns3,usb3-phy"; +}; + +&serdes2 { + serdes2_usb_link: phy@1 { + reg = <1>; + cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_USB3>; + resets = <&serdes_wiz2 2>; + }; +}; + +&usbss1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_usbss1_pins_default>; + ti,vbus-divider; +}; + +&usb1 { + dr_mode = "host"; + maximum-speed = "super-speed"; + phys = <&serdes2_usb_link>; + phy-names = "cdns3,usb3-phy"; +}; + +&tscadc0 { + /* Unused */ + status = "disabled"; +}; + +&tscadc1 { + /* Unused */ + status = "disabled"; +}; + +&mcu_cpsw { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>; +}; + +&davinci_mdio { + phy0: ethernet-phy@0 { + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + }; +}; + +&cpsw_port1 { + phy-mode = "rgmii-rxid"; + phy-handle = <&phy0>; +}; + +&dss { + pinctrl-names = "default"; + pinctrl-0 = <&dss_vout0_pins_default>; + + assigned-clocks = <&k3_clks 152 1>, /* VP 1 pixel clock */ + <&k3_clks 152 4>, /* VP 2 pixel clock */ + <&k3_clks 152 9>, /* VP 3 pixel clock */ + <&k3_clks 152 13>; /* VP 4 pixel clock */ + assigned-clock-parents = <&k3_clks 152 2>, /* PLL16_HSDIV0 */ + <&k3_clks 152 6>, /* DPI0_EXT_CLKSEL_OUT0 */ + <&k3_clks 152 11>, /* PLL18_HSDIV0 */ + <&k3_clks 152 18>; /* DPI1_EXT_CLKSEL_OUT0 */ +}; + +&mcasp0 { + /* Unused */ + status = "disabled"; +}; + +&mcasp1 { + /* Unused */ + status = "disabled"; +}; + +&mcasp2 { + /* Unused */ + status = "disabled"; +}; + +&mcasp3 { + /* Unused */ + status = "disabled"; +}; + +&mcasp4 { + /* Unused */ + status = "disabled"; +}; + +&mcasp5 { + /* Unused */ + status = "disabled"; +}; + +&mcasp6 { + /* Brought out on RPi header */ + status = "disabled"; +}; + +&mcasp7 { + /* Unused */ + status = "disabled"; +}; + +&mcasp8 { + /* Unused */ + status = "disabled"; +}; + +&mcasp9 { + /* Unused */ + status = "disabled"; +}; + +&mcasp10 { + /* Unused */ + status = "disabled"; +}; + +&mcasp11 { + /* Brought out on M.2 E Key */ + status = "disabled"; +}; + +&serdes0 { + serdes0_pcie_link: phy@0 { + reg = <0>; + cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_PCIE>; + resets = <&serdes_wiz0 1>; + }; +}; + +&serdes1 { + serdes1_pcie_link: phy@0 { + reg = <0>; + cdns,num-lanes = <2>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_PCIE>; + resets = <&serdes_wiz1 1>, <&serdes_wiz1 2>; + }; +}; + +&pcie0_rc { + pinctrl-names = "default"; + pinctrl-0 = <&ekey_reset_pins_default>; + reset-gpios = <&main_gpio0 72 GPIO_ACTIVE_HIGH>; + + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <1>; +}; + +&pcie1_rc { + pinctrl-names = "default"; + pinctrl-0 = <&mkey_reset_pins_default>; + reset-gpios = <&wkup_gpio0 11 GPIO_ACTIVE_HIGH>; + + phys = <&serdes1_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <2>; +}; + +&pcie2_rc { + /* Unused */ + status = "disabled"; +}; + +&pcie0_ep { + status = "disabled"; + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <1>; +}; + +&pcie1_ep { + status = "disabled"; + phys = <&serdes1_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <2>; +}; + +&pcie2_ep { + /* Unused */ + status = "disabled"; +}; + +&pcie3_rc { + /* Unused */ + status = "disabled"; +}; + +&pcie3_ep { + /* Unused */ + status = "disabled"; +}; + +&dss { + status = "disabled"; +}; + +&icssg0_mdio { + status = "disabled"; +}; + +&icssg1_mdio { + status = "disabled"; +}; + +&ufs_wrapper { + status = "disabled"; +}; -- 2.31.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH V3 3/4] arm64: dts: ti: k3-j721e-sk: Add IPC sub-mailbox nodes 2021-09-29 8:13 [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit Sinthu Raja 2021-09-29 8:13 ` [PATCH V3 1/4] dt-bindings: arm: ti: Add compatible for J721E SK Sinthu Raja 2021-09-29 8:13 ` [PATCH V3 2/4] arm64: dts: ti: Add support " Sinthu Raja @ 2021-09-29 8:13 ` Sinthu Raja 2021-09-29 8:13 ` [PATCH V3 4/4] arm64: dts: ti: k3-j721e-sk: Add DDR carveout memory nodes Sinthu Raja 2021-10-05 23:01 ` [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit Nishanth Menon 4 siblings, 0 replies; 7+ messages in thread From: Sinthu Raja @ 2021-09-29 8:13 UTC (permalink / raw) To: Nishanth Menon, Tero Kristo, Rob Herring Cc: Vignesh Raghavendra, linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja From: Sinthu Raja <sinthu.raja@ti.com> Add the sub-mailbox nodes that are used to communicate between MPU and various remote processors present in the J721E SoCs to the J721E EAIK board. These include the R5F remote processors in the dual-R5F cluster (MCU_R5FSS0) in the MCU domain and the two dual-R5F clusters (MAIN_R5FSS0 & MAIN_R5FSS1) in the MAIN domain; the two C66x DSP remote processors and the single C71x DSP remote processor in the MAIN domain. These sub-mailbox nodes utilize the System Mailbox clusters 0 through 4. All the remaining mailbox clusters are currently not used on A72 core, and are hence disabled. The sub-mailbox nodes added match the hard-coded mailbox configuration used within the TI RTOS IPC software packages. The R5F processor sub-systems are assumed to be running in Split mode, so a sub-mailbox node is used by each of the R5F cores. Only the sub-mailbox node for the first R5F core in each cluster is used in case of a Lockstep mode for that R5F cluster. Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> --- arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 129 +++++++++++++++++++++++++ 1 file changed, 129 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts index 2ca92ed12f03..7816aa9b06f0 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts +++ b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts @@ -727,3 +727,132 @@ &icssg1_mdio { &ufs_wrapper { status = "disabled"; }; + +&mailbox0_cluster0 { + interrupts = <436>; + + mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 { + ti,mbox-rx = <0 0 0>; + ti,mbox-tx = <1 0 0>; + }; + + mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 { + ti,mbox-rx = <2 0 0>; + ti,mbox-tx = <3 0 0>; + }; +}; + +&mailbox0_cluster1 { + interrupts = <432>; + + mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 { + ti,mbox-rx = <0 0 0>; + ti,mbox-tx = <1 0 0>; + }; + + mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 { + ti,mbox-rx = <2 0 0>; + ti,mbox-tx = <3 0 0>; + }; +}; + +&mailbox0_cluster2 { + interrupts = <428>; + + mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 { + ti,mbox-rx = <0 0 0>; + ti,mbox-tx = <1 0 0>; + }; + + mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 { + ti,mbox-rx = <2 0 0>; + ti,mbox-tx = <3 0 0>; + }; +}; + +&mailbox0_cluster3 { + interrupts = <424>; + + mbox_c66_0: mbox-c66-0 { + ti,mbox-rx = <0 0 0>; + ti,mbox-tx = <1 0 0>; + }; + + mbox_c66_1: mbox-c66-1 { + ti,mbox-rx = <2 0 0>; + ti,mbox-tx = <3 0 0>; + }; +}; + +&mailbox0_cluster4 { + interrupts = <420>; + + mbox_c71_0: mbox-c71-0 { + ti,mbox-rx = <0 0 0>; + ti,mbox-tx = <1 0 0>; + }; +}; + +&mailbox0_cluster5 { + status = "disabled"; +}; + +&mailbox0_cluster6 { + status = "disabled"; +}; + +&mailbox0_cluster7 { + status = "disabled"; +}; + +&mailbox0_cluster8 { + status = "disabled"; +}; + +&mailbox0_cluster9 { + status = "disabled"; +}; + +&mailbox0_cluster10 { + status = "disabled"; +}; + +&mailbox0_cluster11 { + status = "disabled"; +}; + +&mcu_r5fss0_core0 { + mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>; +}; + +&mcu_r5fss0_core1 { + mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core1>; +}; + +&main_r5fss0_core0 { + mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core0>; +}; + +&main_r5fss0_core1 { + mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core1>; +}; + +&main_r5fss1_core0 { + mboxes = <&mailbox0_cluster2 &mbox_main_r5fss1_core0>; +}; + +&main_r5fss1_core1 { + mboxes = <&mailbox0_cluster2 &mbox_main_r5fss1_core1>; +}; + +&c66_0 { + mboxes = <&mailbox0_cluster3 &mbox_c66_0>; +}; + +&c66_1 { + mboxes = <&mailbox0_cluster3 &mbox_c66_1>; +}; + +&c71_0 { + mboxes = <&mailbox0_cluster4 &mbox_c71_0>; +}; -- 2.31.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH V3 4/4] arm64: dts: ti: k3-j721e-sk: Add DDR carveout memory nodes 2021-09-29 8:13 [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit Sinthu Raja ` (2 preceding siblings ...) 2021-09-29 8:13 ` [PATCH V3 3/4] arm64: dts: ti: k3-j721e-sk: Add IPC sub-mailbox nodes Sinthu Raja @ 2021-09-29 8:13 ` Sinthu Raja 2021-10-05 23:01 ` [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit Nishanth Menon 4 siblings, 0 replies; 7+ messages in thread From: Sinthu Raja @ 2021-09-29 8:13 UTC (permalink / raw) To: Nishanth Menon, Tero Kristo, Rob Herring Cc: Vignesh Raghavendra, linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja From: Sinthu Raja <sinthu.raja@ti.com> Two carveout reserved memory nodes each have been added for each of the other remote processors devices within the MAIN domain on the TI J721E SK boards. These nodes are assigned to the respective rproc device nodes as well. The first region will be used as the DMA pool for the rproc devices, and the second region will furnish the static carveout regions for the firmware memory. An additional reserved memory node is also added to reserve a portion of the DDR memory to be used for performing inter-processor communication between all the remote processors running RTOS or baremetal firmwares. 8 MB of memory is reserved for this purpose, and this accounts for all the vrings and vring buffers between all the possible pairs of remote processors. The current carveout addresses and sizes are defined statically for each rproc device. The R5F processors do not have an MMU, and as such require the exact memory used by the firmwares to be set-aside. The C71x DSP processor does support a MMU called CMMU, but is not currently supported and as such requires the exact memory used by the firmware to be set-aside. The firmware images do not require any RSC_CARVEOUT entries in their resource tables to allocate the memory for firmware memory segments Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> --- The following new warnings are introduced. Please refer to the ongoing discussion [1] arch/arm64/boot/dts/ti/k3-j721e-sk.dt.yaml:0:0: /reserved-memory/r5f-dma-memory@a0000000: failed to match any schema with compatible: ['shared-dma-pool'] arch/arm64/boot/dts/ti/k3-j721e-sk.dt.yaml:0:0: /reserved-memory/r5f-memory@a0100000: failed to match any schema with compatible: ['shared-dma-pool'] arch/arm64/boot/dts/ti/k3-j721e-sk.dt.yaml:0:0: /reserved-memory/r5f-dma-memory@a1000000: failed to match any schema with compatible: ['shared-dma-pool'] arch/arm64/boot/dts/ti/k3-j721e-sk.dt.yaml:0:0: /reserved-memory/r5f-memory@a1100000: failed to match any schema with compatible: ['shared-dma-pool'] arch/arm64/boot/dts/ti/k3-j721e-sk.dt.yaml:0:0: /reserved-memory/r5f-dma-memory@a2000000: failed to match any schema with compatible: ['shared-dma-pool'] [1] https://lore.kernel.org/linux-devicetree/20210423163234.3651547-2-thierry.reding@gmail.com/ arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 144 +++++++++++++++++++++++++ 1 file changed, 144 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts index 7816aa9b06f0..b726310d867c 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts +++ b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts @@ -28,6 +28,132 @@ memory@80000000 { <0x00000008 0x80000000 0x00000000 0x80000000>; }; + reserved_memory: reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secure_ddr: optee@9e800000 { + reg = <0x00 0x9e800000 0x00 0x01800000>; + alignment = <0x1000>; + no-map; + }; + + mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa0000000 0x00 0x100000>; + no-map; + }; + + mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa0100000 0x00 0xf00000>; + no-map; + }; + + mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa1000000 0x00 0x100000>; + no-map; + }; + + mcu_r5fss0_core1_memory_region: r5f-memory@a1100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa1100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a2000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa2000000 0x00 0x100000>; + no-map; + }; + + main_r5fss0_core0_memory_region: r5f-memory@a2100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa2100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a3000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa3000000 0x00 0x100000>; + no-map; + }; + + main_r5fss0_core1_memory_region: r5f-memory@a3100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa3100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a4000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa4000000 0x00 0x100000>; + no-map; + }; + + main_r5fss1_core0_memory_region: r5f-memory@a4100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa4100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a5000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa5000000 0x00 0x100000>; + no-map; + }; + + main_r5fss1_core1_memory_region: r5f-memory@a5100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa5100000 0x00 0xf00000>; + no-map; + }; + + c66_1_dma_memory_region: c66-dma-memory@a6000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa6000000 0x00 0x100000>; + no-map; + }; + + c66_0_memory_region: c66-memory@a6100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa6100000 0x00 0xf00000>; + no-map; + }; + + c66_0_dma_memory_region: c66-dma-memory@a7000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa7000000 0x00 0x100000>; + no-map; + }; + + c66_1_memory_region: c66-memory@a7100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa7100000 0x00 0xf00000>; + no-map; + }; + + c71_0_dma_memory_region: c71-dma-memory@a8000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa8000000 0x00 0x100000>; + no-map; + }; + + c71_0_memory_region: c71-memory@a8100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa8100000 0x00 0xf00000>; + no-map; + }; + + rtos_ipc_memory_region: ipc-memories@aa000000 { + reg = <0x00 0xaa000000 0x00 0x01c00000>; + alignment = <0x1000>; + no-map; + }; + }; + vusb_main: fixedregulator-vusb-main5v0 { /* USB MAIN INPUT 5V DC */ compatible = "regulator-fixed"; @@ -823,36 +949,54 @@ &mailbox0_cluster11 { &mcu_r5fss0_core0 { mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>; + memory-region = <&mcu_r5fss0_core0_dma_memory_region>, + <&mcu_r5fss0_core0_memory_region>; }; &mcu_r5fss0_core1 { mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core1>; + memory-region = <&mcu_r5fss0_core1_dma_memory_region>, + <&mcu_r5fss0_core1_memory_region>; }; &main_r5fss0_core0 { mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core0>; + memory-region = <&main_r5fss0_core0_dma_memory_region>, + <&main_r5fss0_core0_memory_region>; }; &main_r5fss0_core1 { mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core1>; + memory-region = <&main_r5fss0_core1_dma_memory_region>, + <&main_r5fss0_core1_memory_region>; }; &main_r5fss1_core0 { mboxes = <&mailbox0_cluster2 &mbox_main_r5fss1_core0>; + memory-region = <&main_r5fss1_core0_dma_memory_region>, + <&main_r5fss1_core0_memory_region>; }; &main_r5fss1_core1 { mboxes = <&mailbox0_cluster2 &mbox_main_r5fss1_core1>; + memory-region = <&main_r5fss1_core1_dma_memory_region>, + <&main_r5fss1_core1_memory_region>; }; &c66_0 { mboxes = <&mailbox0_cluster3 &mbox_c66_0>; + memory-region = <&c66_0_dma_memory_region>, + <&c66_0_memory_region>; }; &c66_1 { mboxes = <&mailbox0_cluster3 &mbox_c66_1>; + memory-region = <&c66_1_dma_memory_region>, + <&c66_1_memory_region>; }; &c71_0 { mboxes = <&mailbox0_cluster4 &mbox_c71_0>; + memory-region = <&c71_0_dma_memory_region>, + <&c71_0_memory_region>; }; -- 2.31.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit 2021-09-29 8:13 [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit Sinthu Raja ` (3 preceding siblings ...) 2021-09-29 8:13 ` [PATCH V3 4/4] arm64: dts: ti: k3-j721e-sk: Add DDR carveout memory nodes Sinthu Raja @ 2021-10-05 23:01 ` Nishanth Menon 4 siblings, 0 replies; 7+ messages in thread From: Nishanth Menon @ 2021-10-05 23:01 UTC (permalink / raw) To: Sinthu Raja, Tero Kristo, Rob Herring Cc: Nishanth Menon, linux-arm-kernel, Sinthu Raja, devicetree, Vignesh Raghavendra, linux-kernel On Wed, 29 Sep 2021 13:43:29 +0530, Sinthu Raja wrote: > From: Sinthu Raja <sinthu.raja@ti.com> > > Hi, > This series of patches add support for J721e Starter kit(SK)[1]. J721e SK > is a low cost, small form factor board designed for TI’s J721E SoC. > > Changes in V3: > - Introduced IPC sub mailbox nodes patch. > - Introduced DDR carveout memory nodes patch. > - Updated board name to starter kit > - Fixed DTS binding errors. > - Updated commit message, $subject which includes adding board URL, > > [...] Hi Sinthu Raja, I have applied the following to branch ti-k3-dts-next on [1]. Thank you! [1/4] dt-bindings: arm: ti: Add compatible for J721E SK commit: 2927c9a56e36788859606f445a5290bf21c9ab53 [2/4] arm64: dts: ti: Add support for J721E SK commit: 1bfda92a3a36c4dbd2b15a7f6660b673f4a2e475 [3/4] arm64: dts: ti: k3-j721e-sk: Add IPC sub-mailbox nodes commit: e910e5b6763d8b895ca1bba918a39d20e3361358 [4/4] arm64: dts: ti: k3-j721e-sk: Add DDR carveout memory nodes commit: f46d16cf5b43b66de030f0e3b2f20d24ba95f369 Side note: - There are still cleanups that are in works (tsadc, cdns, etc..) - since these are already present and active cleanup is going on, letting it past, but if I do get a push back from upstream maintainers, I'd have to pull the series back. - I had applied the yaml cleanup for j721e, so I had to apply based on the offset. Let me know if the changes are troublesome, else no action is needed - I have built and run it through the usual guantlet as best as I can. All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted. You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed. If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced. Please add any relevant lists and maintainers to the CCs when replying to this mail. [1] git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux.git -- Regards, Nishanth Menon Key (0xDDB5849D1736249D)/Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2021-10-05 23:01 UTC | newest] Thread overview: 7+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2021-09-29 8:13 [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit Sinthu Raja 2021-09-29 8:13 ` [PATCH V3 1/4] dt-bindings: arm: ti: Add compatible for J721E SK Sinthu Raja 2021-10-04 18:43 ` Rob Herring 2021-09-29 8:13 ` [PATCH V3 2/4] arm64: dts: ti: Add support " Sinthu Raja 2021-09-29 8:13 ` [PATCH V3 3/4] arm64: dts: ti: k3-j721e-sk: Add IPC sub-mailbox nodes Sinthu Raja 2021-09-29 8:13 ` [PATCH V3 4/4] arm64: dts: ti: k3-j721e-sk: Add DDR carveout memory nodes Sinthu Raja 2021-10-05 23:01 ` [PATCH V3 0/4] arm64: dts: ti: Add support for J721E starter kit Nishanth Menon
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).