From: Li Yang <leoyang.li@nxp.com>
To: Shawn Guo <shawnguo@kernel.org>, Rob Herring <robh+dt@kernel.org>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Cc: Li Yang <leoyang.li@nxp.com>
Subject: [PATCH v3 03/17] ARM: dts: ls1021a: change dma channels order to match schema
Date: Tue, 12 Oct 2021 18:58:09 -0500 [thread overview]
Message-ID: <20211012235824.31096-4-leoyang.li@nxp.com> (raw)
In-Reply-To: <20211012235824.31096-1-leoyang.li@nxp.com>
Although the ordering of DMA channels was not relevant in the txt binding,
it is defined as ordered in the converted yaml schema. Update the dts
to match the order.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
---
arch/arm/boot/dts/ls1021a.dtsi | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi
index 77f983b589fa..960de957f0b4 100644
--- a/arch/arm/boot/dts/ls1021a.dtsi
+++ b/arch/arm/boot/dts/ls1021a.dtsi
@@ -395,8 +395,8 @@ i2c0: i2c@2180000 {
reg = <0x0 0x2180000 0x0 0x10000>;
interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clockgen 4 1>;
- dma-names = "tx", "rx";
- dmas = <&edma0 1 39>, <&edma0 1 38>;
+ dma-names = "rx", "tx";
+ dmas = <&edma0 1 38>, <&edma0 1 39>;
status = "disabled";
};
@@ -407,8 +407,8 @@ i2c1: i2c@2190000 {
reg = <0x0 0x2190000 0x0 0x10000>;
interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clockgen 4 1>;
- dma-names = "tx", "rx";
- dmas = <&edma0 1 37>, <&edma0 1 36>;
+ dma-names = "rx", "tx";
+ dmas = <&edma0 1 36>, <&edma0 1 37>;
status = "disabled";
};
@@ -419,8 +419,8 @@ i2c2: i2c@21a0000 {
reg = <0x0 0x21a0000 0x0 0x10000>;
interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clockgen 4 1>;
- dma-names = "tx", "rx";
- dmas = <&edma0 1 35>, <&edma0 1 34>;
+ dma-names = "rx", "tx";
+ dmas = <&edma0 1 34>, <&edma0 1 35>;
status = "disabled";
};
--
2.25.1
next prev parent reply other threads:[~2021-10-13 0:06 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-12 23:58 [PATCH v3 00/17] Cleanup of LS1021a device trees Li Yang
2021-10-12 23:58 ` [PATCH v3 01/17] dt-bindings: arm: fsl: add ls1021a-tsn board Li Yang
2021-10-12 23:58 ` [PATCH v3 02/17] ARM: dts: ls1021a: remove clock-names property for i2c nodes Li Yang
2021-10-12 23:58 ` Li Yang [this message]
2021-10-12 23:58 ` [PATCH v3 04/17] ARM: dts: ls1021a: change to use SPDX identifiers Li Yang
2021-10-12 23:58 ` [PATCH v3 05/17] ARM: dts: ls1021a-qds: Add node for QSPI flash Li Yang
2021-10-12 23:58 ` [PATCH v3 06/17] ARM: dts: ls1021a: update pcie nodes for dt-schema check Li Yang
2021-10-12 23:58 ` [PATCH v3 07/17] ARM: dts: ls1021a: fix board compatible to follow binding schema Li Yang
2021-10-12 23:58 ` [PATCH v3 08/17] ARM: dts: ls1021a: breakup long values in thermal node Li Yang
2021-10-12 23:58 ` [PATCH v3 09/17] ARM: dts: ls1021a: disable ifc node by default Li Yang
2021-10-12 23:58 ` [PATCH v3 10/17] ARM: dts: ls1021a: remove regulators simple-bus Li Yang
2021-10-12 23:58 ` [PATCH v3 11/17] ARM: dts: ls1021a: fix memory node for schema check Li Yang
2021-10-12 23:58 ` [PATCH v3 12/17] ARM: dts: ls1021a: add #dma-cells to qdma node Li Yang
2021-10-12 23:58 ` [PATCH v3 13/17] ARM: dts: ls1021a: add #power-domain-cells for power-controller node Li Yang
2021-10-12 23:58 ` [PATCH v3 14/17] ARM: dts: ls1021a-qds: change fpga to simple-mfd device Li Yang
2021-10-12 23:58 ` [PATCH v3 15/17] ARM: dts: ls1021a-tsn: remove undocumented property "position" from mma8452 node Li Yang
2021-10-12 23:58 ` [PATCH v3 16/17] ARM: dts: ls1021a: move thermal-zones node out of soc/ Li Yang
2021-10-12 23:58 ` [PATCH v3 17/17] ARM: dts: ls1021a-tsn: use generic "jedec,spi-nor" compatible for flash Li Yang
2021-10-15 3:17 ` [PATCH v3 00/17] Cleanup of LS1021a device trees Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211012235824.31096-4-leoyang.li@nxp.com \
--to=leoyang.li@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).