[PATCH v3 0/3] Driver for TI INA238 I2C Power Monitor

[PATCH v3 0/3] Driver for TI INA238 I2C Power Monitor

[Nathan Rossi]

From: Nathan Rossi <nathan.rossi@digi.com>

Changes in v2:
- Added device tree binding for ti,shunt-gain to specify the target
  ADCRANGE for the ina238
- Reworked ina238 driver to use hwmon_chip_info API, and addressed
  various review comments

Changes in v3:
- Fix schema error for ti,shunt-gain binding
- Address review comments

Nathan Rossi (3):
  dt-bindings: hwmon: ti,ina2xx: Document ti,ina238 compatible string
  dt-bindings: hwmon: ti,ina2xx: Add ti,shunt-gain property
  hwmon: Driver for Texas Instruments INA238

 .../devicetree/bindings/hwmon/ti,ina2xx.yaml  |  22 +
 Documentation/hwmon/ina238.rst                |  56 ++
 Documentation/hwmon/index.rst                 |   1 +
 drivers/hwmon/Kconfig                         |  12 +
 drivers/hwmon/Makefile                        |   1 +
 drivers/hwmon/ina238.c                        | 644 ++++++++++++++++++
 6 files changed, 736 insertions(+)
 create mode 100644 Documentation/hwmon/ina238.rst
 create mode 100644 drivers/hwmon/ina238.c
---
2.33.0

[PATCH v3 1/3] dt-bindings: hwmon: ti,ina2xx: Document ti,ina238 compatible string

[Nathan Rossi]

From: Nathan Rossi <nathan.rossi@digi.com>

Document the compatible string for the Texas Instruments INA238, this
device is a variant of the existing INA2xx devices and has the same
device tree bindings (shunt resistor).

Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
---
 Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml b/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml
index 6f0443322a..180573f26c 100644
--- a/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml
+++ b/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml
@@ -26,6 +26,7 @@ properties:
       - ti,ina226
       - ti,ina230
       - ti,ina231
+      - ti,ina238
 
   reg:
     maxItems: 1
---
2.33.0

[PATCH v3 2/3] dt-bindings: hwmon: ti,ina2xx: Add ti,shunt-gain property

[Nathan Rossi]

From: Nathan Rossi <nathan.rossi@digi.com>

Add a property to the binding to define the selected shunt voltage gain.
This specifies the range and accuracy that applies to the shunt circuit.
This property only applies to devices that have a selectable shunt
voltage range via PGA or ADCRANGE register configuration.

Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
---
Changes in v2:
- Added binding for shunt-gain

Changes in v3:
- Fix schema error, setting $ref to uint32
- Improve the description to detail exactly how to define the property
  and how the property affects initial device configuration and
  calculation of values
---
 .../devicetree/bindings/hwmon/ti,ina2xx.yaml        | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml b/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml
index 180573f26c..47af97bb4c 100644
--- a/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml
+++ b/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml
@@ -36,6 +36,27 @@ properties:
       Shunt resistor value in micro-Ohm.
     $ref: /schemas/types.yaml#/definitions/uint32
 
+  ti,shunt-gain:
+    description: |
+      Programmable gain divisor for the shunt voltage accuracy and range. This
+      property only applies to devices that have configurable PGA/ADCRANGE. The
+      gain value is used configure the gain and to convert the shunt voltage,
+      current and power register values when reading measurements from the
+      device.
+
+      For devices that have a configurable PGA (e.g. INA209, INA219, INA220),
+      the gain value maps directly with the PG bits of the config register.
+
+      For devices that have ADCRANGE configuration (e.g. INA238) a shunt-gain
+      value of 1 maps to ADCRANGE=1 where no gain divisor is applied to the
+      shunt voltage, and a value of 4 maps to ADCRANGE=0 such that a wider
+      voltage range is used.
+
+      The default value is device dependent, and is defined by the reset value
+      of PGA/ADCRANGE in the respective configuration registers.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 2, 4, 8]
+
 required:
   - compatible
   - reg
---
2.33.0