From: Vladimir Oltean <vladimir.oltean@nxp.com>
To: "Clément Léger" <clement.leger@bootlin.com>
Cc: "David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Claudiu Manoil <claudiu.manoil@nxp.com>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
"UNGLinuxDriver@microchip.com" <UNGLinuxDriver@microchip.com>,
Andrew Lunn <andrew@lunn.ch>,
"netdev@vger.kernel.org" <netdev@vger.kernel.org>,
"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Subject: Re: [PATCH v2 4/6] net: ocelot: add support for ndo_change_mtu
Date: Wed, 3 Nov 2021 12:40:55 +0000 [thread overview]
Message-ID: <20211103124054.pcgruuipw5cpup6v@skbuf> (raw)
In-Reply-To: <20211103091943.3878621-5-clement.leger@bootlin.com>
On Wed, Nov 03, 2021 at 10:19:41AM +0100, Clément Léger wrote:
> This commit adds support for changing MTU for the ocelot register based
> interface. For ocelot, JUMBO frame size can be set up to 25000 bytes
> but has been set to 9000 which is a saner value and allow for maximum
> gain of performances. Frames larger than 9000 bytes do not yield
> a noticeable improvement.
>
> Signed-off-by: Clément Léger <clement.leger@bootlin.com>
> ---
> drivers/net/ethernet/mscc/ocelot.h | 2 ++
> drivers/net/ethernet/mscc/ocelot_net.c | 14 ++++++++++++++
> 2 files changed, 16 insertions(+)
>
> diff --git a/drivers/net/ethernet/mscc/ocelot.h b/drivers/net/ethernet/mscc/ocelot.h
> index e43da09b8f91..ba0dec7dd64f 100644
> --- a/drivers/net/ethernet/mscc/ocelot.h
> +++ b/drivers/net/ethernet/mscc/ocelot.h
> @@ -32,6 +32,8 @@
>
> #define OCELOT_PTP_QUEUE_SZ 128
>
> +#define OCELOT_JUMBO_MTU 9000
> +
> struct ocelot_port_tc {
> bool block_shared;
> unsigned long offload_cnt;
> diff --git a/drivers/net/ethernet/mscc/ocelot_net.c b/drivers/net/ethernet/mscc/ocelot_net.c
> index d76def435b23..5916492fd6d0 100644
> --- a/drivers/net/ethernet/mscc/ocelot_net.c
> +++ b/drivers/net/ethernet/mscc/ocelot_net.c
> @@ -482,6 +482,18 @@ static netdev_tx_t ocelot_port_xmit(struct sk_buff *skb, struct net_device *dev)
> return NETDEV_TX_OK;
> }
>
> +static int ocelot_change_mtu(struct net_device *dev, int new_mtu)
> +{
> + struct ocelot_port_private *priv = netdev_priv(dev);
> + struct ocelot_port *ocelot_port = &priv->port;
> + struct ocelot *ocelot = ocelot_port->ocelot;
> +
> + ocelot_port_set_maxlen(ocelot, priv->chip_port, new_mtu);
> + WRITE_ONCE(dev->mtu, new_mtu);
The WRITE_ONCE seems absolutely gratuitous to me.
> +
> + return 0;
> +}
> +
> enum ocelot_action_type {
> OCELOT_MACT_LEARN,
> OCELOT_MACT_FORGET,
> @@ -768,6 +780,7 @@ static const struct net_device_ops ocelot_port_netdev_ops = {
> .ndo_open = ocelot_port_open,
> .ndo_stop = ocelot_port_stop,
> .ndo_start_xmit = ocelot_port_xmit,
> + .ndo_change_mtu = ocelot_change_mtu,
> .ndo_set_rx_mode = ocelot_set_rx_mode,
> .ndo_set_mac_address = ocelot_port_set_mac_address,
> .ndo_get_stats64 = ocelot_get_stats64,
> @@ -1699,6 +1712,7 @@ int ocelot_probe_port(struct ocelot *ocelot, int port, struct regmap *target,
>
> dev->netdev_ops = &ocelot_port_netdev_ops;
> dev->ethtool_ops = &ocelot_ethtool_ops;
> + dev->max_mtu = OCELOT_JUMBO_MTU;
>
> dev->hw_features |= NETIF_F_HW_VLAN_CTAG_FILTER | NETIF_F_RXFCS |
> NETIF_F_HW_TC;
> --
> 2.33.0
>
next prev parent reply other threads:[~2021-11-03 12:40 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-11-03 9:19 [PATCH v2 0/6] Add FDMA support on ocelot switch driver Clément Léger
2021-11-03 9:19 ` [PATCH v2 1/6] net: ocelot: add support to get port mac from device-tree Clément Léger
2021-11-03 10:26 ` Vladimir Oltean
2021-11-15 11:19 ` Julian Wiedmann
2021-11-15 11:24 ` Clément Léger
2021-11-03 9:19 ` [PATCH v2 2/6] dt-bindings: net: convert mscc,vsc7514-switch bindings to yaml Clément Léger
2021-11-03 10:45 ` Vladimir Oltean
2021-11-08 11:13 ` Clément Léger
2021-11-12 20:06 ` Rob Herring
2021-11-03 9:19 ` [PATCH v2 3/6] net: ocelot: pre-compute injection frame header content Clément Léger
2021-11-03 12:38 ` Vladimir Oltean
2021-11-03 13:53 ` Clément Léger
2021-11-15 10:13 ` Clément Léger
2021-11-15 10:51 ` Vladimir Oltean
2021-11-15 10:58 ` Clément Léger
2021-11-15 14:08 ` Jakub Kicinski
2021-11-15 14:06 ` Clément Léger
2021-11-15 14:31 ` Vladimir Oltean
2021-11-15 16:03 ` Clément Léger
2021-11-03 9:19 ` [PATCH v2 4/6] net: ocelot: add support for ndo_change_mtu Clément Léger
2021-11-03 12:40 ` Vladimir Oltean [this message]
2021-11-03 13:07 ` Clément Léger
2021-11-03 9:19 ` [PATCH v2 5/6] net: ocelot: add FDMA support Clément Léger
2021-11-03 11:25 ` Denis Kirjanov
2021-11-03 12:31 ` Vladimir Oltean
2021-11-03 14:22 ` Clément Léger
2021-11-03 9:19 ` [PATCH v2 6/6] net: ocelot: add jumbo frame support for FDMA Clément Léger
2021-11-03 12:43 ` Vladimir Oltean
2021-11-03 14:30 ` Clément Léger
2021-11-03 10:46 ` [PATCH v2 0/6] Add FDMA support on ocelot switch driver Denis Kirjanov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211103124054.pcgruuipw5cpup6v@skbuf \
--to=vladimir.oltean@nxp.com \
--cc=UNGLinuxDriver@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=andrew@lunn.ch \
--cc=claudiu.manoil@nxp.com \
--cc=clement.leger@bootlin.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox