From: jae.hyun.yoo@intel.com
To: Rob Herring <robh+dt@kernel.org>, Corey Minyard <minyard@acm.org>,
Joel Stanley <joel@jms.id.au>, Andrew Jeffery <andrew@aj.id.au>,
Cedric Le Goater <clg@kaod.org>,
Haiyue Wang <haiyue.wang@linux.intel.com>,
ChiaWei Wang <chiawei_wang@aspeedtech.com>,
Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-aspeed@lists.ozlabs.org,
openipmi-developer@lists.sourceforge.net
Subject: [PATCH v3 5/6] dt-bindings: ipmi: aspeed,kcs-bmc: add 'clocks' as a required property
Date: Mon, 8 Nov 2021 11:01:59 -0800 [thread overview]
Message-ID: <20211108190200.290957-6-jae.hyun.yoo@intel.com> (raw)
In-Reply-To: <20211108190200.290957-1-jae.hyun.yoo@intel.com>
From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
If LPC KCS driver is registered ahead of lpc-ctrl module, LPC KCS
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.
To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property as one of
required properties to enable the LCLK by the LPC KCS driver.
Note: dtsi change in this patch series should be applied along with,
and dtbs should be re-compiled after applying this series since
it's adding a new required property otherwise the driver will not
be probed correctly.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
---
v2 -> v3:
* Made commit message more descriptive.
v1 -> v2:
Changes sinve v1:
* Added 'clocks' property into kcs-bmc bindings using
'aspeed,ast2400-kcs-bmc.yaml' because it's not merged into
'aspeed-lpc.yaml' yet. The bindings merging could be done using a
separate patch later.
.../devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml
index 4ff6fabfcb30..92ec0da047f4 100644
--- a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml
+++ b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml
@@ -71,9 +71,14 @@ properties:
$ref: '/schemas/types.yaml#/definitions/uint32'
description: The host CPU IO map address
+ clocks:
+ maxItems: 1
+ description: Reference clock for the LPC controller
+
required:
- compatible
- interrupts
+ - clocks
additionalProperties: false
@@ -96,6 +101,7 @@ allOf:
examples:
- |
+ #include <dt-bindings/clock/aspeed-clock.h>
#include <dt-bindings/interrupt-controller/irq.h>
kcs3: kcs@24 {
compatible = "aspeed,ast2600-kcs-bmc";
@@ -103,4 +109,5 @@ examples:
aspeed,lpc-io-reg = <0xca2>;
aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
interrupts = <8>;
+ clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
};
--
2.25.1
next prev parent reply other threads:[~2021-11-08 18:42 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-11-08 19:01 [PATCH v3 0/6] Add LCLK control into Aspeed LPC sub drivers jae.hyun.yoo
2021-11-08 19:01 ` [PATCH v3 1/6] ARM: dts: aspeed: add LCLK setting into LPC IBT node jae.hyun.yoo
2021-11-08 19:01 ` [PATCH v3 2/6] dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property jae.hyun.yoo
2021-11-19 1:07 ` Rob Herring
2021-11-08 19:01 ` [PATCH v3 3/6] ipmi: bt: add clock control logic jae.hyun.yoo
2021-11-08 19:01 ` [PATCH v3 4/6] ARM: dts: aspeed: add LCLK setting into LPC KCS nodes jae.hyun.yoo
2021-11-08 19:01 ` jae.hyun.yoo [this message]
2021-11-19 1:08 ` [PATCH v3 5/6] dt-bindings: ipmi: aspeed,kcs-bmc: add 'clocks' as a required property Rob Herring
2021-11-08 19:02 ` [PATCH v3 6/6] ipmi: kcs_bmc_aspeed: add clock control logic jae.hyun.yoo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211108190200.290957-6-jae.hyun.yoo@intel.com \
--to=jae.hyun.yoo@intel.com \
--cc=andrew@aj.id.au \
--cc=chiawei_wang@aspeedtech.com \
--cc=clg@kaod.org \
--cc=devicetree@vger.kernel.org \
--cc=haiyue.wang@linux.intel.com \
--cc=jae.hyun.yoo@linux.intel.com \
--cc=joel@jms.id.au \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=minyard@acm.org \
--cc=openipmi-developer@lists.sourceforge.net \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).