devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Vinod Koul <vkoul@kernel.org>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org, Vinod Koul <vkoul@kernel.org>,
	Andy Gross <agross@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Konrad Dybcio <konrad.dybcio@somainline.org>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v2 07/13] arm64: dts: qcom: sm8450: add ufs nodes
Date: Thu,  9 Dec 2021 16:04:59 +0530	[thread overview]
Message-ID: <20211209103505.197453-8-vkoul@kernel.org> (raw)
In-Reply-To: <20211209103505.197453-1-vkoul@kernel.org>

Add the UFS and QMP PHY node for SM8450 SoC

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 72 ++++++++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index d29680c405bf..9556d2fc46e0 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -815,6 +815,78 @@ rpmhcc: clock-controller {
 				clocks = <&xo_board>;
 			};
 		};
+
+		ufs_mem_hc: ufshc@1d84000 {
+			compatible = "qcom,sm8450-ufshc", "qcom,ufshc",
+				     "jedec,ufs-2.0";
+			reg = <0 0x01d84000 0 0x3000>;
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&ufs_mem_phy_lanes>;
+			phy-names = "ufsphy";
+			lanes-per-direction = <2>;
+			#reset-cells = <1>;
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "rst";
+
+			power-domains = <&gcc UFS_PHY_GDSC>;
+
+			iommus = <&apps_smmu 0xe0 0x0>;
+
+			clock-names =
+				"core_clk",
+				"bus_aggr_clk",
+				"iface_clk",
+				"core_clk_unipro",
+				"ref_clk",
+				"tx_lane0_sync_clk",
+				"rx_lane0_sync_clk",
+				"rx_lane1_sync_clk";
+			clocks =
+				<&gcc GCC_UFS_PHY_AXI_CLK>,
+				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				<&gcc GCC_UFS_PHY_AHB_CLK>,
+				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				<&rpmhcc RPMH_CXO_CLK>,
+				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+			freq-table-hz =
+				<75000000 300000000>,
+				<0 0>,
+				<0 0>,
+				<75000000 300000000>,
+				<75000000 300000000>,
+				<0 0>,
+				<0 0>,
+				<0 0>;
+			status = "disabled";
+		};
+
+		ufs_mem_phy: phy@1d87000 {
+			compatible = "qcom,sm8450-qmp-ufs-phy";
+			reg = <0 0x01d87000 0 0xe10>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clock-names = "ref", "ref_aux", "qref";
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
+				 <&gcc GCC_UFS_0_CLKREF_EN>;
+
+			resets = <&ufs_mem_hc 0>;
+			reset-names = "ufsphy";
+			status = "disabled";
+
+			ufs_mem_phy_lanes: lanes@1d87400 {
+				reg = <0 0x01d87400 0 0x108>,
+				      <0 0x01d87600 0 0x1e0>,
+				      <0 0x01d87c00 0 0x1dc>,
+				      <0 0x01d87800 0 0x108>,
+				      <0 0x01d87a00 0 0x1e0>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+			};
+		};
 	};
 
 	timer {
-- 
2.31.1


  parent reply	other threads:[~2021-12-09 10:35 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-12-09 10:34 [PATCH v2 00/13] arm64: dts: qcom: Add support for SM8450 SoC and QRD board Vinod Koul
2021-12-09 10:34 ` [PATCH v2 01/13] arm64: dts: qcom: Add base SM8450 DTSI Vinod Koul
2021-12-09 10:34 ` [PATCH v2 02/13] arm64: dts: qcom: sm8450: Add tlmm nodes Vinod Koul
2021-12-09 10:34 ` [PATCH v2 03/13] arm64: dts: qcom: sm8450: Add reserved memory nodes Vinod Koul
2021-12-09 10:34 ` [PATCH v2 04/13] arm64: dts: qcom: sm8450: add smmu nodes Vinod Koul
2021-12-09 10:34 ` [PATCH v2 05/13] arm64: dts: qcom: Add base SM8450 QRD DTS Vinod Koul
2021-12-09 23:06   ` kernel test robot
2021-12-10  3:13   ` kernel test robot
2021-12-09 10:34 ` [PATCH v2 06/13] arm64: dts: qcom: sm8450-qrd: Add rpmh regulator nodes Vinod Koul
2021-12-09 10:34 ` Vinod Koul [this message]
2021-12-09 10:35 ` [PATCH v2 08/13] arm64: dts: qcom: sm8450-qrd: enable ufs nodes Vinod Koul
2021-12-09 10:35 ` [PATCH v2 09/13] arm64: dts: qcom: sm8450: add interconnect nodes Vinod Koul
2021-12-09 15:46   ` Konrad Dybcio
2021-12-10  9:37   ` Georgi Djakov
2021-12-09 10:35 ` [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node Vinod Koul
2022-10-24 14:56   ` Krzysztof Kozlowski
2022-10-24 15:06     ` konrad.dybcio
2022-10-24 16:16       ` Krzysztof Kozlowski
2022-10-24 16:45     ` Dmitry Baryshkov
2022-10-24 16:46       ` Krzysztof Kozlowski
2022-10-24 16:48         ` Dmitry Baryshkov
2022-10-24 18:56           ` Krzysztof Kozlowski
2022-10-24 18:58             ` Dmitry Baryshkov
2022-10-26  5:33               ` Vinod Koul
2022-11-17 14:57                 ` Konrad Dybcio
2022-11-18  9:16                   ` Konrad Dybcio
2021-12-09 10:35 ` [PATCH v2 11/13] arm64: dts: qcom: sm8450: Add rpmhpd node Vinod Koul
2021-12-09 10:35 ` [PATCH v2 12/13] arm64: dts: qcom: sm8450: add cpufreq support Vinod Koul
2021-12-09 10:35 ` [PATCH v2 13/13] arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes Vinod Koul
2021-12-09 15:47   ` Konrad Dybcio

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20211209103505.197453-8-vkoul@kernel.org \
    --to=vkoul@kernel.org \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=konrad.dybcio@somainline.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).