* [PATCH v2 1/5] ARM: dts: imx6dl-prtvt7: Add display and panel nodes
2022-01-31 10:28 [PATCH v2 0/5] ARM: dts: protonic maintenance patches Oleksij Rempel
@ 2022-01-31 10:28 ` Oleksij Rempel
2022-01-31 10:28 ` [PATCH v2 2/5] ARM: dts: imx6dl-prtvt7: Add missing tvp5150 video decoder node Oleksij Rempel
` (3 subsequent siblings)
4 siblings, 0 replies; 9+ messages in thread
From: Oleksij Rempel @ 2022-01-31 10:28 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, Robin van der Gracht, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander, dri-devel
Add Innolux G070Y2-T02 panel to the Protonic VT7 board.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 190d26642bc8..be7c4cb339e7 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -28,6 +28,30 @@ backlight_lcd: backlight-lcd {
power-supply = <®_bl_12v0>;
};
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
keys {
compatible = "gpio-keys";
autorepeat;
@@ -135,6 +159,18 @@ led-debug0 {
};
};
+ panel {
+ compatible = "innolux,g070y2-t02";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
reg_bl_12v0: regulator-bl-12v0 {
compatible = "regulator-fixed";
pinctrl-names = "default";
@@ -146,6 +182,13 @@ reg_bl_12v0: regulator-bl-12v0 {
enable-active-high;
};
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
reg_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1v8";
@@ -275,6 +318,10 @@ &ipu1 {
status = "okay";
};
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
--
2.30.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH v2 2/5] ARM: dts: imx6dl-prtvt7: Add missing tvp5150 video decoder node
2022-01-31 10:28 [PATCH v2 0/5] ARM: dts: protonic maintenance patches Oleksij Rempel
2022-01-31 10:28 ` [PATCH v2 1/5] ARM: dts: imx6dl-prtvt7: Add display and panel nodes Oleksij Rempel
@ 2022-01-31 10:28 ` Oleksij Rempel
2022-02-11 13:12 ` Shawn Guo
2022-01-31 10:28 ` [PATCH v2 3/5] ARM: dts: imx6qdl-vicut1: add CAN termination support Oleksij Rempel
` (2 subsequent siblings)
4 siblings, 1 reply; 9+ messages in thread
From: Oleksij Rempel @ 2022-01-31 10:28 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Robin van der Gracht, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, dri-devel
From: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
---
arch/arm/boot/dts/imx6dl-prtvt7.dts | 42 +++++++++++++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index be7c4cb339e7..baaa6ffc4df9 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -6,6 +6,7 @@
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/display/sdtv-standards.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/sound/fsl-imx-audmux.h>
@@ -171,6 +172,18 @@ panel_in: endpoint {
};
};
+ connector {
+ compatible = "composite-video-connector";
+ label = "Composite0";
+ sdtv-standards = <SDTV_STD_PAL_B>;
+
+ port {
+ comp0_out: endpoint {
+ remote-endpoint = <&tvp5150_comp0_in>;
+ };
+ };
+ };
+
reg_bl_12v0: regulator-bl-12v0 {
compatible = "regulator-fixed";
pinctrl-names = "default";
@@ -295,6 +308,31 @@ sgtl5000: audio-codec@a {
VDDIO-supply = <®_3v3>;
VDDD-supply = <®_1v8>;
};
+
+ video@5c {
+ compatible = "ti,tvp5150";
+ reg = <0x5c>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tvp5150_comp0_in: endpoint {
+ remote-endpoint = <&comp0_out>;
+ };
+ };
+
+ /* Output port 2 is video output pad */
+ port@2 {
+ reg = <2>;
+
+ tvp5151_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ };
+ };
+ };
};
&i2c3 {
@@ -322,6 +360,10 @@ &ipu1_di0_disp0 {
remote-endpoint = <&display_in>;
};
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
--
2.30.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* Re: [PATCH v2 2/5] ARM: dts: imx6dl-prtvt7: Add missing tvp5150 video decoder node
2022-01-31 10:28 ` [PATCH v2 2/5] ARM: dts: imx6dl-prtvt7: Add missing tvp5150 video decoder node Oleksij Rempel
@ 2022-02-11 13:12 ` Shawn Guo
0 siblings, 0 replies; 9+ messages in thread
From: Shawn Guo @ 2022-02-11 13:12 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, Rob Herring, Sascha Hauer, Thierry Reding,
Sam Ravnborg, David Airlie, Daniel Vetter, Robin van der Gracht,
devicetree, Fabio Estevam, linux-arm-kernel, linux-kernel,
NXP Linux Team, Pengutronix Kernel Team, David Jander, dri-devel
On Mon, Jan 31, 2022 at 11:28:38AM +0100, Oleksij Rempel wrote:
> From: Robin van der Gracht <robin@protonic.nl>
>
> Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Please write up some commit log. Also your SoB is missing.
Shawn
> ---
> arch/arm/boot/dts/imx6dl-prtvt7.dts | 42 +++++++++++++++++++++++++++++
> 1 file changed, 42 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> index be7c4cb339e7..baaa6ffc4df9 100644
> --- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
> +++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
> @@ -6,6 +6,7 @@
> /dts-v1/;
> #include "imx6dl.dtsi"
> #include "imx6qdl-prti6q.dtsi"
> +#include <dt-bindings/display/sdtv-standards.h>
> #include <dt-bindings/input/input.h>
> #include <dt-bindings/leds/common.h>
> #include <dt-bindings/sound/fsl-imx-audmux.h>
> @@ -171,6 +172,18 @@ panel_in: endpoint {
> };
> };
>
> + connector {
> + compatible = "composite-video-connector";
> + label = "Composite0";
> + sdtv-standards = <SDTV_STD_PAL_B>;
> +
> + port {
> + comp0_out: endpoint {
> + remote-endpoint = <&tvp5150_comp0_in>;
> + };
> + };
> + };
> +
> reg_bl_12v0: regulator-bl-12v0 {
> compatible = "regulator-fixed";
> pinctrl-names = "default";
> @@ -295,6 +308,31 @@ sgtl5000: audio-codec@a {
> VDDIO-supply = <®_3v3>;
> VDDD-supply = <®_1v8>;
> };
> +
> + video@5c {
> + compatible = "ti,tvp5150";
> + reg = <0x5c>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + tvp5150_comp0_in: endpoint {
> + remote-endpoint = <&comp0_out>;
> + };
> + };
> +
> + /* Output port 2 is video output pad */
> + port@2 {
> + reg = <2>;
> +
> + tvp5151_to_ipu1_csi0_mux: endpoint {
> + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
> + };
> + };
> + };
> };
>
> &i2c3 {
> @@ -322,6 +360,10 @@ &ipu1_di0_disp0 {
> remote-endpoint = <&display_in>;
> };
>
> +&ipu1_csi0_mux_from_parallel_sensor {
> + remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
> +};
> +
> &pwm1 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_pwm1>;
> --
> 2.30.2
>
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH v2 3/5] ARM: dts: imx6qdl-vicut1: add CAN termination support
2022-01-31 10:28 [PATCH v2 0/5] ARM: dts: protonic maintenance patches Oleksij Rempel
2022-01-31 10:28 ` [PATCH v2 1/5] ARM: dts: imx6dl-prtvt7: Add display and panel nodes Oleksij Rempel
2022-01-31 10:28 ` [PATCH v2 2/5] ARM: dts: imx6dl-prtvt7: Add missing tvp5150 video decoder node Oleksij Rempel
@ 2022-01-31 10:28 ` Oleksij Rempel
[not found] ` <YfgCmNgvx7pwpBFV@ravnborg.org>
2022-01-31 10:28 ` [PATCH v2 4/5] ARM: dts: imx6dl: plym2m, prtvt7, victgo: make use of new resistive-adc-touch driver Oleksij Rempel
2022-01-31 10:28 ` [PATCH v2 5/5] ARM: dts: imx6dl: plym2m, prtvt7, victgo: add thermal zones and hwmon Oleksij Rempel
4 siblings, 1 reply; 9+ messages in thread
From: Oleksij Rempel @ 2022-01-31 10:28 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht, dri-devel
The gpio1 0 pin is controlling CAN termination, not USB H1 VBUS. So,
remove wrong regulator and assign this gpio to new DT CAN termnation
property.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 12 ++----------
1 file changed, 2 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index b9e305774fed..1ac7e13249d2 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -126,15 +126,6 @@ reg_3v3: regulator-3v3 {
regulator-max-microvolt = <3300000>;
};
- reg_h1_vbus: regulator-h1-vbus {
- compatible = "regulator-fixed";
- regulator-name = "h1-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
reg_otg_vbus: regulator-otg-vbus {
compatible = "regulator-fixed";
regulator-name = "otg-vbus";
@@ -212,6 +203,8 @@ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1>;
+ termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ termination-ohms = <150>;
status = "okay";
};
@@ -492,7 +485,6 @@ &uart5 {
};
&usbh1 {
- vbus-supply = <®_h1_vbus>;
pinctrl-names = "default";
phy_type = "utmi";
dr_mode = "host";
--
2.30.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH v2 4/5] ARM: dts: imx6dl: plym2m, prtvt7, victgo: make use of new resistive-adc-touch driver
2022-01-31 10:28 [PATCH v2 0/5] ARM: dts: protonic maintenance patches Oleksij Rempel
` (2 preceding siblings ...)
2022-01-31 10:28 ` [PATCH v2 3/5] ARM: dts: imx6qdl-vicut1: add CAN termination support Oleksij Rempel
@ 2022-01-31 10:28 ` Oleksij Rempel
[not found] ` <YfgDToubMLxZsy34@ravnborg.org>
2022-01-31 10:28 ` [PATCH v2 5/5] ARM: dts: imx6dl: plym2m, prtvt7, victgo: add thermal zones and hwmon Oleksij Rempel
4 siblings, 1 reply; 9+ messages in thread
From: Oleksij Rempel @ 2022-01-31 10:28 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht, dri-devel
The tsc2046 is an ADC used as touchscreen controller. To share as mach
code as possible, we should use it as actual ADC + virtual touchscreen
controller.
With this patch we make use of the new kernel IIO and HID infrastructure.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-plym2m.dts | 59 +++++++++++++++++++++--------
arch/arm/boot/dts/imx6dl-prtvt7.dts | 57 +++++++++++++++++++++-------
arch/arm/boot/dts/imx6dl-victgo.dts | 59 ++++++++++++++++++++++-------
3 files changed, 132 insertions(+), 43 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 60fe5f14666e..73c7622bfe0f 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -101,6 +101,18 @@ reg_12v0: regulator-12v0 {
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
};
+
+ touchscreen {
+ compatible = "resistive-adc-touch";
+ io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
+ <&adc_ts 5>;
+ io-channel-names = "y", "z1", "z2", "x";
+ touchscreen-min-pressure = <64687>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ touchscreen-x-plate-ohms = <300>;
+ touchscreen-y-plate-ohms = <800>;
+ };
};
&can1 {
@@ -129,26 +141,41 @@ &ecspi2 {
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
- touchscreen@0 {
- compatible = "ti,tsc2046";
+ adc_ts: adc@0 {
+ compatible = "ti,tsc2046e-adc";
reg = <0>;
pinctrl-0 = <&pinctrl_tsc2046>;
pinctrl-names ="default";
- spi-max-frequency = <100000>;
- interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
- pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+ spi-max-frequency = <1000000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+ #io-channel-cells = <1>;
- touchscreen-inverted-x;
- touchscreen-inverted-y;
- touchscreen-max-pressure = <4095>;
-
- ti,vref-delay-usecs = /bits/ 16 <100>;
- ti,x-plate-ohms = /bits/ 16 <800>;
- ti,y-plate-ohms = /bits/ 16 <300>;
- ti,debounce-max = /bits/ 16 <3>;
- ti,debounce-tol = /bits/ 16 <70>;
- ti,debounce-rep = /bits/ 16 <3>;
- wakeup-source;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@1 {
+ reg = <1>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@3 {
+ reg = <3>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@4 {
+ reg = <4>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
};
};
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index baaa6ffc4df9..59e0674420a1 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -235,6 +235,18 @@ simple-audio-card,codec {
frame-master;
};
};
+
+ touchscreen {
+ compatible = "resistive-adc-touch";
+ io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
+ <&adc_ts 5>;
+ io-channel-names = "y", "z1", "z2", "x";
+ touchscreen-min-pressure = <64687>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ touchscreen-x-plate-ohms = <300>;
+ touchscreen-y-plate-ohms = <800>;
+ };
};
&audmux {
@@ -277,22 +289,41 @@ &ecspi2 {
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
- touchscreen@0 {
- compatible = "ti,tsc2046";
+ adc_ts: adc@0 {
+ compatible = "ti,tsc2046e-adc";
reg = <0>;
pinctrl-0 = <&pinctrl_tsc>;
pinctrl-names ="default";
- spi-max-frequency = <100000>;
- interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
- pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
- touchscreen-max-pressure = <4095>;
- ti,vref-delay-usecs = /bits/ 16 <100>;
- ti,x-plate-ohms = /bits/ 16 <800>;
- ti,y-plate-ohms = /bits/ 16 <300>;
- ti,debounce-max = /bits/ 16 <3>;
- ti,debounce-tol = /bits/ 16 <70>;
- ti,debounce-rep = /bits/ 16 <3>;
- wakeup-source;
+ spi-max-frequency = <1000000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+ #io-channel-cells = <1>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@1 {
+ reg = <1>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@3 {
+ reg = <3>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@4 {
+ reg = <4>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
};
};
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index d37ba4ed847d..52de091ea452 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -181,6 +181,18 @@ simple-audio-card,codec {
frame-master;
};
};
+
+ touchscreen {
+ compatible = "resistive-adc-touch";
+ io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
+ <&adc_ts 5>;
+ io-channel-names = "y", "z1", "z2", "x";
+ touchscreen-min-pressure = <64687>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ touchscreen-x-plate-ohms = <300>;
+ touchscreen-y-plate-ohms = <800>;
+ };
};
&audmux {
@@ -244,22 +256,41 @@ &ecspi2 {
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
- touchscreen@0 {
- compatible = "ti,tsc2046";
+ adc_ts: adc@0 {
+ compatible = "ti,tsc2046e-adc";
reg = <0>;
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_touchscreen>;
- spi-max-frequency = <200000>;
- interrupts-extended = <&gpio5 8 IRQ_TYPE_EDGE_FALLING>;
- pendown-gpio = <&gpio5 8 GPIO_ACTIVE_LOW>;
- touchscreen-size-x = <800>;
- touchscreen-size-y = <480>;
- touchscreen-inverted-y;
- touchscreen-max-pressure = <4095>;
- ti,vref-delay-usecs = /bits/ 16 <100>;
- ti,x-plate-ohms = /bits/ 16 <800>;
- ti,y-plate-ohms = /bits/ 16 <300>;
- wakeup-source;
+ pinctrl-names ="default";
+ spi-max-frequency = <1000000>;
+ interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
+ #io-channel-cells = <1>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@1 {
+ reg = <1>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@3 {
+ reg = <3>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@4 {
+ reg = <4>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
};
};
--
2.30.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH v2 5/5] ARM: dts: imx6dl: plym2m, prtvt7, victgo: add thermal zones and hwmon
2022-01-31 10:28 [PATCH v2 0/5] ARM: dts: protonic maintenance patches Oleksij Rempel
` (3 preceding siblings ...)
2022-01-31 10:28 ` [PATCH v2 4/5] ARM: dts: imx6dl: plym2m, prtvt7, victgo: make use of new resistive-adc-touch driver Oleksij Rempel
@ 2022-01-31 10:28 ` Oleksij Rempel
4 siblings, 0 replies; 9+ messages in thread
From: Oleksij Rempel @ 2022-01-31 10:28 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Robin van der Gracht, dri-devel
Add thermal zones and hwmon connected to the ADC-touchscreen controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/imx6dl-plym2m.dts | 74 ++++++++++++++++++++++++++++-
arch/arm/boot/dts/imx6dl-prtvt7.dts | 57 ++++++++++++++++++++++
arch/arm/boot/dts/imx6dl-victgo.dts | 62 +++++++++++++++++++++++-
3 files changed, 191 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 73c7622bfe0f..c4ce23d8ac9f 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -50,6 +50,11 @@ display_out: endpoint {
};
};
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&vdiv_vaccu>;
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -102,6 +107,26 @@ reg_12v0: regulator-12v0 {
regulator-max-microvolt = <12000000>;
};
+ thermal-zones {
+ chassis-thermal {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&tsens0>;
+ };
+
+ touch-thermal0 {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&touch_temp0>;
+ };
+
+ touch-thermal1 {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&touch_temp1>;
+ };
+ };
+
touchscreen {
compatible = "resistive-adc-touch";
io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
@@ -113,6 +138,32 @@ touchscreen {
touchscreen-x-plate-ohms = <300>;
touchscreen-y-plate-ohms = <800>;
};
+
+ touch_temp0: touch-temperature-sensor0 {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&adc_ts 0>;
+ io-channel-names = "sensor-channel";
+ temperature-lookup-table = < (-40000) 736
+ 85000 474>;
+ };
+
+ touch_temp1: touch-temperature-sensor1 {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&adc_ts 7>;
+ io-channel-names = "sensor-channel";
+ temperature-lookup-table = < (-40000) 826
+ 85000 609>;
+ };
+
+ vdiv_vaccu: voltage-divider-vaccu {
+ compatible = "voltage-divider";
+ io-channels = <&adc_ts 2>;
+ output-ohms = <2500>;
+ full-ohms = <64000>;
+ #io-channel-cells = <0>;
+ };
};
&can1 {
@@ -153,12 +204,24 @@ adc_ts: adc@0 {
#address-cells = <1>;
#size-cells = <0>;
+ channel@0 {
+ reg = <0>;
+ settling-time-us = <300>;
+ oversampling-ratio = <5>;
+ };
+
channel@1 {
reg = <1>;
settling-time-us = <700>;
oversampling-ratio = <5>;
};
+ channel@2 {
+ reg = <2>;
+ settling-time-us = <300>;
+ oversampling-ratio = <5>;
+ };
+
channel@3 {
reg = <3>;
settling-time-us = <700>;
@@ -176,6 +239,14 @@ channel@5 {
settling-time-us = <700>;
oversampling-ratio = <5>;
};
+
+ /* channel 6 is not connected */
+
+ channel@7 {
+ reg = <7>;
+ settling-time-us = <300>;
+ oversampling-ratio = <5>;
+ };
};
};
@@ -260,9 +331,10 @@ &i2c3 {
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
- temperature-sensor@70 {
+ tsens0: temperature-sensor@70 {
compatible = "ti,tmp103";
reg = <0x70>;
+ #thermal-sensor-cells = <0>;
};
};
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 59e0674420a1..b86deebef7b7 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -53,6 +53,11 @@ display_out: endpoint {
};
};
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&vdiv_vaccu>;
+ };
+
keys {
compatible = "gpio-keys";
autorepeat;
@@ -236,6 +241,26 @@ simple-audio-card,codec {
};
};
+ thermal-zones {
+ chassis-thermal {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&tsens0>;
+ };
+
+ touch-thermal0 {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&touch_temp0>;
+ };
+
+ touch-thermal1 {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&touch_temp1>;
+ };
+ };
+
touchscreen {
compatible = "resistive-adc-touch";
io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
@@ -247,6 +272,32 @@ touchscreen {
touchscreen-x-plate-ohms = <300>;
touchscreen-y-plate-ohms = <800>;
};
+
+ touch_temp0: touch-temperature-sensor0 {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&adc_ts 0>;
+ io-channel-names = "sensor-channel";
+ temperature-lookup-table = < (-40000) 736
+ 85000 474>;
+ };
+
+ touch_temp1: touch-temperature-sensor1 {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&adc_ts 7>;
+ io-channel-names = "sensor-channel";
+ temperature-lookup-table = < (-40000) 826
+ 85000 609>;
+ };
+
+ vdiv_vaccu: voltage-divider-vaccu {
+ compatible = "voltage-divider";
+ io-channels = <&adc_ts 2>;
+ output-ohms = <2500>;
+ full-ohms = <64000>;
+ #io-channel-cells = <0>;
+ };
};
&audmux {
@@ -372,6 +423,12 @@ rtc@51 {
reg = <0x51>;
};
+ tsens0: temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ #thermal-sensor-cells = <0>;
+ };
+
gpio_pca: gpio@74 {
compatible = "nxp,pca9539";
reg = <0x74>;
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 52de091ea452..227c952543d4 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -66,6 +66,11 @@ enter {
};
};
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&vdiv_vaccu>, <&vdiv_hitch_pos>;
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -182,6 +187,26 @@ simple-audio-card,codec {
};
};
+ thermal-zones {
+ chassis-thermal {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&tsens0>;
+ };
+
+ touch-thermal0 {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&touch_temp0>;
+ };
+
+ touch-thermal1 {
+ polling-delay = <20000>;
+ polling-delay-passive = <0>;
+ thermal-sensors = <&touch_temp1>;
+ };
+ };
+
touchscreen {
compatible = "resistive-adc-touch";
io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
@@ -193,6 +218,40 @@ touchscreen {
touchscreen-x-plate-ohms = <300>;
touchscreen-y-plate-ohms = <800>;
};
+
+ touch_temp0: touch-temperature-sensor0 {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&adc_ts 0>;
+ io-channel-names = "sensor-channel";
+ temperature-lookup-table = < (-40000) 736
+ 85000 474>;
+ };
+
+ touch_temp1: touch-temperature-sensor1 {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&adc_ts 7>;
+ io-channel-names = "sensor-channel";
+ temperature-lookup-table = < (-40000) 826
+ 85000 609>;
+ };
+
+ vdiv_vaccu: voltage-divider-vaccu {
+ compatible = "voltage-divider";
+ io-channels = <&adc_ts 2>;
+ output-ohms = <2500>;
+ full-ohms = <64000>;
+ #io-channel-cells = <0>;
+ };
+
+ vdiv_hitch_pos: voltage-divider-hitch-pos {
+ compatible = "voltage-divider";
+ io-channels = <&adc_ts 6>;
+ output-ohms = <3300>;
+ full-ohms = <13300>;
+ #io-channel-cells = <0>;
+ };
};
&audmux {
@@ -477,9 +536,10 @@ rtc@51 {
reg = <0x51>;
};
- temperature-sensor@70 {
+ tsens0: temperature-sensor@70 {
compatible = "ti,tmp103";
reg = <0x70>;
+ #thermal-sensor-cells = <0>;
};
};
--
2.30.2
^ permalink raw reply related [flat|nested] 9+ messages in thread