* [PATCH RESEND v6 0/2] Make AUX gpio pin optional for ktd2692 @ 2022-05-04 15:04 Markuss Broks 2022-05-04 15:04 ` [PATCH RESEND v6 1/2] dt-bindings: leds: convert ktd2692 bindings to yaml Markuss Broks 2022-05-04 15:04 ` [PATCH RESEND v6 2/2] leds: ktd2692: Make aux-gpios optional Markuss Broks 0 siblings, 2 replies; 4+ messages in thread From: Markuss Broks @ 2022-05-04 15:04 UTC (permalink / raw) To: pavel Cc: Markuss Broks, Rob Herring, Krzysztof Kozlowski, Linus Walleij, Lad Prabhakar, Christophe JAILLET, linux-leds, devicetree, linux-kernel Some appliances of ktd2692 don't have the AUX pin connected to a GPIO. Specifically, Samsung Galaxy J5 (2015), which uses ktd2692 for driving the front flash LED, has the pin not connected anywhere on schematics. Make specifying the AUX pin optional, since it is additional functionality and only affects amount of current going through the LED. Also convert the txt device-tree bindings to yaml and pick up maintenance over the yaml binding and the driver itself. v2: - fix the dt_binding_check v3: - set the aux_gpio to NULL to avoid passing ERR_PTR as a gpio v4: - maintainership -> maintenance (description) - remove the if (led->aux_gpio) - use devm_gpiod_get_optional for aux gpio v5: - use ret to pass a correct error return code (Christophe) v6: - use PTR_ERR properly (when IS_ERR is true) (Christophe) Markuss Broks (2): dt-bindings: leds: convert ktd2692 bindings to yaml leds: ktd2692: Make aux-gpios optional .../bindings/leds/kinetic,ktd2692.yaml | 87 +++++++++++++++++++ .../devicetree/bindings/leds/leds-ktd2692.txt | 50 ----------- MAINTAINERS | 6 ++ drivers/leds/flash/leds-ktd2692.c | 18 ++-- 4 files changed, 103 insertions(+), 58 deletions(-) create mode 100644 Documentation/devicetree/bindings/leds/kinetic,ktd2692.yaml delete mode 100644 Documentation/devicetree/bindings/leds/leds-ktd2692.txt -- 2.35.1 ^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH RESEND v6 1/2] dt-bindings: leds: convert ktd2692 bindings to yaml 2022-05-04 15:04 [PATCH RESEND v6 0/2] Make AUX gpio pin optional for ktd2692 Markuss Broks @ 2022-05-04 15:04 ` Markuss Broks 2022-05-04 15:26 ` Andy Shevchenko 2022-05-04 15:04 ` [PATCH RESEND v6 2/2] leds: ktd2692: Make aux-gpios optional Markuss Broks 1 sibling, 1 reply; 4+ messages in thread From: Markuss Broks @ 2022-05-04 15:04 UTC (permalink / raw) To: pavel Cc: Markuss Broks, Andy Shevchenko, Rob Herring, Krzysztof Kozlowski, Christophe JAILLET, Lad Prabhakar, Linus Walleij, linux-leds, devicetree, linux-kernel This patch converts the leds-ktd2692.txt bindings to modern yaml style device-tree bindings. Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Markuss Broks <markuss.broks@gmail.com> --- .../bindings/leds/kinetic,ktd2692.yaml | 87 +++++++++++++++++++ .../devicetree/bindings/leds/leds-ktd2692.txt | 50 ----------- 2 files changed, 87 insertions(+), 50 deletions(-) create mode 100644 Documentation/devicetree/bindings/leds/kinetic,ktd2692.yaml delete mode 100644 Documentation/devicetree/bindings/leds/leds-ktd2692.txt diff --git a/Documentation/devicetree/bindings/leds/kinetic,ktd2692.yaml b/Documentation/devicetree/bindings/leds/kinetic,ktd2692.yaml new file mode 100644 index 000000000000..bac95a51afa1 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/kinetic,ktd2692.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/kinetic,ktd2692.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: KTD2692 Flash LED Driver from Kinetic Technologies + +maintainers: + - Markuss Broks <markuss.broks@gmail.com> + +description: | + KTD2692 is the ideal power solution for high-power flash LEDs. + It uses ExpressWire single-wire programming for maximum flexibility. + + The ExpressWire interface through CTRL pin can control LED on/off and + enable/disable the IC, Movie(max 1/3 of Flash current) / Flash mode current, + Flash timeout, LVP(low voltage protection). + + Also, When the AUX pin is pulled high while CTRL pin is high, + LED current will be ramped up to the flash-mode current level. + +properties: + compatible: + const: kinetic,ktd2692 + + ctrl-gpios: + maxItems: 1 + description: Specifier of the GPIO connected to CTRL pin. + + aux-gpios: + maxItems: 1 + description: Specifier of the GPIO connected to CTRL pin. + + vin-supply: + description: LED supply (2.7V to 5.5V). + + led: + type: object + $ref: common.yaml# + description: Properties for the LED. + properties: + function: true + color: true + flash-max-timeout-us: + description: Flash LED maximum timeout. + + led-max-microamp: + maximum: 300000 + description: Minimum Threshold for Timer protection + is defined internally (Maximum 300mA). + + flash-max-microamp: + maximum: 300000 + description: Flash LED maximum current + Formula - I(uA) = 15000000 / Rset. + + additionalProperties: false + +required: + - compatible + - ctrl-gpios + - led + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/leds/common.h> + + ktd2692 { + compatible = "kinetic,ktd2692"; + ctrl-gpios = <&gpc0 1 0>; + aux-gpios = <&gpc0 2 0>; + vin-supply = <&vbat>; + + led { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; + flash-max-timeout-us = <250000>; + flash-max-microamp = <150000>; + led-max-microamp = <25000>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/leds/leds-ktd2692.txt b/Documentation/devicetree/bindings/leds/leds-ktd2692.txt deleted file mode 100644 index 853737452580..000000000000 --- a/Documentation/devicetree/bindings/leds/leds-ktd2692.txt +++ /dev/null @@ -1,50 +0,0 @@ -* Kinetic Technologies - KTD2692 Flash LED Driver - -KTD2692 is the ideal power solution for high-power flash LEDs. -It uses ExpressWire single-wire programming for maximum flexibility. - -The ExpressWire interface through CTRL pin can control LED on/off and -enable/disable the IC, Movie(max 1/3 of Flash current) / Flash mode current, -Flash timeout, LVP(low voltage protection). - -Also, When the AUX pin is pulled high while CTRL pin is high, -LED current will be ramped up to the flash-mode current level. - -Required properties: -- compatible : Should be "kinetic,ktd2692". -- ctrl-gpios : Specifier of the GPIO connected to CTRL pin. -- aux-gpios : Specifier of the GPIO connected to AUX pin. - -Optional properties: -- vin-supply : "vin" LED supply (2.7V to 5.5V). - See Documentation/devicetree/bindings/regulator/regulator.txt - -A discrete LED element connected to the device must be represented by a child -node - See Documentation/devicetree/bindings/leds/common.txt - -Required properties for flash LED child nodes: - See Documentation/devicetree/bindings/leds/common.txt -- led-max-microamp : Minimum Threshold for Timer protection - is defined internally (Maximum 300mA). -- flash-max-microamp : Flash LED maximum current - Formula : I(mA) = 15000 / Rset. -- flash-max-timeout-us : Flash LED maximum timeout. - -Optional properties for flash LED child nodes: -- label : See Documentation/devicetree/bindings/leds/common.txt - -Example: - -ktd2692 { - compatible = "kinetic,ktd2692"; - ctrl-gpios = <&gpc0 1 0>; - aux-gpios = <&gpc0 2 0>; - vin-supply = <&vbat>; - - flash-led { - label = "ktd2692-flash"; - led-max-microamp = <300000>; - flash-max-microamp = <1500000>; - flash-max-timeout-us = <1835000>; - }; -}; -- 2.35.1 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH RESEND v6 1/2] dt-bindings: leds: convert ktd2692 bindings to yaml 2022-05-04 15:04 ` [PATCH RESEND v6 1/2] dt-bindings: leds: convert ktd2692 bindings to yaml Markuss Broks @ 2022-05-04 15:26 ` Andy Shevchenko 0 siblings, 0 replies; 4+ messages in thread From: Andy Shevchenko @ 2022-05-04 15:26 UTC (permalink / raw) To: Markuss Broks Cc: Pavel Machek, Rob Herring, Krzysztof Kozlowski, Christophe JAILLET, Lad Prabhakar, Linus Walleij, Linux LED Subsystem, devicetree, Linux Kernel Mailing List On Wed, May 4, 2022 at 5:06 PM Markuss Broks <markuss.broks@gmail.com> wrote: > > This patch converts the leds-ktd2692.txt bindings to modern yaml > style device-tree bindings. > Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> > > Signed-off-by: Markuss Broks <markuss.broks@gmail.com> There must be no blank lines in the tag block. > --- > .../bindings/leds/kinetic,ktd2692.yaml | 87 +++++++++++++++++++ > .../devicetree/bindings/leds/leds-ktd2692.txt | 50 ----------- > 2 files changed, 87 insertions(+), 50 deletions(-) > create mode 100644 Documentation/devicetree/bindings/leds/kinetic,ktd2692.yaml > delete mode 100644 Documentation/devicetree/bindings/leds/leds-ktd2692.txt > > diff --git a/Documentation/devicetree/bindings/leds/kinetic,ktd2692.yaml b/Documentation/devicetree/bindings/leds/kinetic,ktd2692.yaml > new file mode 100644 > index 000000000000..bac95a51afa1 > --- /dev/null > +++ b/Documentation/devicetree/bindings/leds/kinetic,ktd2692.yaml > @@ -0,0 +1,87 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/leds/kinetic,ktd2692.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: KTD2692 Flash LED Driver from Kinetic Technologies > + > +maintainers: > + - Markuss Broks <markuss.broks@gmail.com> > + > +description: | > + KTD2692 is the ideal power solution for high-power flash LEDs. > + It uses ExpressWire single-wire programming for maximum flexibility. > + > + The ExpressWire interface through CTRL pin can control LED on/off and > + enable/disable the IC, Movie(max 1/3 of Flash current) / Flash mode current, > + Flash timeout, LVP(low voltage protection). > + > + Also, When the AUX pin is pulled high while CTRL pin is high, > + LED current will be ramped up to the flash-mode current level. > + > +properties: > + compatible: > + const: kinetic,ktd2692 > + > + ctrl-gpios: > + maxItems: 1 > + description: Specifier of the GPIO connected to CTRL pin. > + > + aux-gpios: > + maxItems: 1 > + description: Specifier of the GPIO connected to CTRL pin. > + > + vin-supply: > + description: LED supply (2.7V to 5.5V). > + > + led: > + type: object > + $ref: common.yaml# > + description: Properties for the LED. > + properties: > + function: true > + color: true > + flash-max-timeout-us: > + description: Flash LED maximum timeout. > + > + led-max-microamp: > + maximum: 300000 > + description: Minimum Threshold for Timer protection > + is defined internally (Maximum 300mA). > + > + flash-max-microamp: > + maximum: 300000 > + description: Flash LED maximum current > + Formula - I(uA) = 15000000 / Rset. > + > + additionalProperties: false > + > +required: > + - compatible > + - ctrl-gpios > + - led > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + #include <dt-bindings/leds/common.h> > + > + ktd2692 { > + compatible = "kinetic,ktd2692"; > + ctrl-gpios = <&gpc0 1 0>; > + aux-gpios = <&gpc0 2 0>; > + vin-supply = <&vbat>; > + > + led { > + function = LED_FUNCTION_FLASH; > + color = <LED_COLOR_ID_WHITE>; > + flash-max-timeout-us = <250000>; > + flash-max-microamp = <150000>; > + led-max-microamp = <25000>; > + }; > + }; > + > +... > diff --git a/Documentation/devicetree/bindings/leds/leds-ktd2692.txt b/Documentation/devicetree/bindings/leds/leds-ktd2692.txt > deleted file mode 100644 > index 853737452580..000000000000 > --- a/Documentation/devicetree/bindings/leds/leds-ktd2692.txt > +++ /dev/null > @@ -1,50 +0,0 @@ > -* Kinetic Technologies - KTD2692 Flash LED Driver > - > -KTD2692 is the ideal power solution for high-power flash LEDs. > -It uses ExpressWire single-wire programming for maximum flexibility. > - > -The ExpressWire interface through CTRL pin can control LED on/off and > -enable/disable the IC, Movie(max 1/3 of Flash current) / Flash mode current, > -Flash timeout, LVP(low voltage protection). > - > -Also, When the AUX pin is pulled high while CTRL pin is high, > -LED current will be ramped up to the flash-mode current level. > - > -Required properties: > -- compatible : Should be "kinetic,ktd2692". > -- ctrl-gpios : Specifier of the GPIO connected to CTRL pin. > -- aux-gpios : Specifier of the GPIO connected to AUX pin. > - > -Optional properties: > -- vin-supply : "vin" LED supply (2.7V to 5.5V). > - See Documentation/devicetree/bindings/regulator/regulator.txt > - > -A discrete LED element connected to the device must be represented by a child > -node - See Documentation/devicetree/bindings/leds/common.txt > - > -Required properties for flash LED child nodes: > - See Documentation/devicetree/bindings/leds/common.txt > -- led-max-microamp : Minimum Threshold for Timer protection > - is defined internally (Maximum 300mA). > -- flash-max-microamp : Flash LED maximum current > - Formula : I(mA) = 15000 / Rset. > -- flash-max-timeout-us : Flash LED maximum timeout. > - > -Optional properties for flash LED child nodes: > -- label : See Documentation/devicetree/bindings/leds/common.txt > - > -Example: > - > -ktd2692 { > - compatible = "kinetic,ktd2692"; > - ctrl-gpios = <&gpc0 1 0>; > - aux-gpios = <&gpc0 2 0>; > - vin-supply = <&vbat>; > - > - flash-led { > - label = "ktd2692-flash"; > - led-max-microamp = <300000>; > - flash-max-microamp = <1500000>; > - flash-max-timeout-us = <1835000>; > - }; > -}; > -- > 2.35.1 > -- With Best Regards, Andy Shevchenko ^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH RESEND v6 2/2] leds: ktd2692: Make aux-gpios optional 2022-05-04 15:04 [PATCH RESEND v6 0/2] Make AUX gpio pin optional for ktd2692 Markuss Broks 2022-05-04 15:04 ` [PATCH RESEND v6 1/2] dt-bindings: leds: convert ktd2692 bindings to yaml Markuss Broks @ 2022-05-04 15:04 ` Markuss Broks 1 sibling, 0 replies; 4+ messages in thread From: Markuss Broks @ 2022-05-04 15:04 UTC (permalink / raw) To: pavel Cc: Markuss Broks, Rob Herring, Rob Herring, Krzysztof Kozlowski, Linus Walleij, Lad Prabhakar, Christophe JAILLET, linux-leds, devicetree, linux-kernel Make the AUX pin optional, since it isn't a core part of functionality, and the device is designed to be operational with only one CTRL pin. Also pick up maintenance for the LED driver and the yaml bindings. Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Markuss Broks <markuss.broks@gmail.com> --- MAINTAINERS | 6 ++++++ drivers/leds/flash/leds-ktd2692.c | 6 +++--- 2 files changed, 9 insertions(+), 3 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index 2db49ea7ae55..8ef5667a1d98 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -10479,6 +10479,12 @@ S: Maintained F: Documentation/devicetree/bindings/leds/backlight/kinetic,ktd253.yaml F: drivers/video/backlight/ktd253-backlight.c +KTD2692 FLASH LED DRIVER +M: Markuss Broks <markuss.broks@gmail.com> +S: Maintained +F: Documentation/devicetree/bindings/leds/backlight/kinetic,ktd2692.yaml +F: drivers/leds/flash/leds-ktd2692.yaml + KTEST M: Steven Rostedt <rostedt@goodmis.org> M: John Hawley <warthog9@eaglescrag.net> diff --git a/drivers/leds/flash/leds-ktd2692.c b/drivers/leds/flash/leds-ktd2692.c index f341da1503a4..01ceea83af67 100644 --- a/drivers/leds/flash/leds-ktd2692.c +++ b/drivers/leds/flash/leds-ktd2692.c @@ -284,9 +284,9 @@ static int ktd2692_parse_dt(struct ktd2692_context *led, struct device *dev, return ret; } - led->aux_gpio = devm_gpiod_get(dev, "aux", GPIOD_ASIS); - ret = PTR_ERR_OR_ZERO(led->aux_gpio); - if (ret) { + led->aux_gpio = devm_gpiod_get_optional(dev, "aux", GPIOD_ASIS); + if (IS_ERR(led->aux_gpio)) { + ret = PTR_ERR(led->aux_gpio); dev_err(dev, "cannot get aux-gpios %d\n", ret); return ret; } -- 2.35.1 ^ permalink raw reply related [flat|nested] 4+ messages in thread
end of thread, other threads:[~2022-05-04 15:27 UTC | newest] Thread overview: 4+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2022-05-04 15:04 [PATCH RESEND v6 0/2] Make AUX gpio pin optional for ktd2692 Markuss Broks 2022-05-04 15:04 ` [PATCH RESEND v6 1/2] dt-bindings: leds: convert ktd2692 bindings to yaml Markuss Broks 2022-05-04 15:26 ` Andy Shevchenko 2022-05-04 15:04 ` [PATCH RESEND v6 2/2] leds: ktd2692: Make aux-gpios optional Markuss Broks
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).