From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzk@kernel.org>,
Konrad Dybcio <konrad.dybcio@somainline.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH v3 0/8] arm64: dts: qcom: initial Inforce IFC6560 board support
Date: Sat, 14 May 2022 02:45:10 +0300 [thread overview]
Message-ID: <20220513234518.3068480-1-dmitry.baryshkov@linaro.org> (raw)
This work is largely based on the previous work by Bjorn Andersson ([1])
Changes since v2:
- Removed useless enablement of mdp node from the board file. It is
already enabled in the SoC dtsi file.
Changes since v1 (mostly based on Kondrad's review):
- Also disabled dsi0/dsi0 phy in sdm630.dtsi
- Removed the clock from BAM DMA devices rather than disabling them
completely
- Replaced numbers with symbolic names for interconnects in sdm630.dtsi
- Switched to "qcom,sda660" as a fallback compatible string
- Added dt-bindings for the qcom,sda660 compat
- Removed extra nesting level from the adsp firmware path
- Replaced numbers with proper symbolic names in the board file
- Added chassis-type property
- Changed the order of blsp entries in the board file
- Removed spurious newlines
- Changed the order of regulator properties
- Changed the DSI data-lines to list all four lanes. Still use just
three lanes for the adv bridge (and describe the reason in the
comment)
Changes since Bjorn's v2:
- Disable dsi1, dsi1 phy, GPU by default in sdm660.dtsi/sdm630.dtsi
- Fix qusb2phy ref clock
- Added USB2 host support to sdm630.dtsi
- Renamed DTS to follow SoC-vendor-board pattern
- Fixed vph_pwr voltage
- Removed extra/unrelated comments
- Added keys, USB2, USB3,
- Added configuration for the attached HDMI bridge
- Enabled MDP, MDSS and DSI0/DSI0 PHY devices
- Removed uart pinctrl and /reserved-mem nodes (present in main dtsi
file)
- Added card detection for the SDCC2
- Disabled BLSP BAM DMA devices, they make the board reset during boot
[1] https://lore.kernel.org/linux-arm-msm/20210825221110.1498718-1-bjorn.andersson@linaro.org/#t
Dmitry Baryshkov (8):
arm64: dts: qcom: sdm660: disable dsi1/dsi1_phy by default
arm64: dts: qcom: sdm630: disable dsi1/dsi1_phy by default
arm64: dts: qcom: sdm630: disable GPU by default
arm64: dts: qcom: sdm630: fix the qusb2phy ref clock
arm64: dts: qcom: sdm630: add second (HS) USB host support
arm64: dts: qcom: sdm630: use defined symbols for interconnects
arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support
dt-bindings: arm: qcom: document sda660 SoC and ifc6560 board
.../devicetree/bindings/arm/qcom.yaml | 6 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/sda660-inforce-ifc6560.dts | 455 ++++++++++++++++++
arch/arm64/boot/dts/qcom/sdm630.dtsi | 85 +++-
arch/arm64/boot/dts/qcom/sdm660.dtsi | 3 +
5 files changed, 538 insertions(+), 12 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts
--
2.35.1
next reply other threads:[~2022-05-13 23:55 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-13 23:45 Dmitry Baryshkov [this message]
2022-05-13 23:45 ` [PATCH v3 1/8] arm64: dts: qcom: sdm660: disable dsi1/dsi1_phy by default Dmitry Baryshkov
2022-05-13 23:45 ` [PATCH v3 2/8] arm64: dts: qcom: sdm630: " Dmitry Baryshkov
2022-05-14 9:37 ` Marijn Suijten
2022-05-14 12:59 ` Dmitry Baryshkov
2022-05-13 23:45 ` [PATCH v3 3/8] arm64: dts: qcom: sdm630: disable GPU " Dmitry Baryshkov
2022-05-14 9:54 ` Marijn Suijten
2022-05-13 23:45 ` [PATCH v3 4/8] arm64: dts: qcom: sdm630: fix the qusb2phy ref clock Dmitry Baryshkov
2022-05-14 9:56 ` Marijn Suijten
2022-05-14 13:00 ` Dmitry Baryshkov
2022-05-13 23:45 ` [PATCH v3 5/8] arm64: dts: qcom: sdm630: add second (HS) USB host support Dmitry Baryshkov
2022-05-14 10:11 ` Marijn Suijten
2022-05-13 23:45 ` [PATCH v3 6/8] arm64: dts: qcom: sdm630: use defined symbols for interconnects Dmitry Baryshkov
2022-05-14 9:45 ` Marijn Suijten
2022-05-14 12:51 ` Dmitry Baryshkov
2022-05-15 14:44 ` Marijn Suijten
2022-05-15 18:05 ` Dmitry Baryshkov
2022-05-13 23:45 ` [PATCH v3 7/8] arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support Dmitry Baryshkov
2022-05-14 10:31 ` Marijn Suijten
2022-05-14 13:09 ` Dmitry Baryshkov
2022-05-13 23:45 ` [PATCH v3 8/8] dt-bindings: arm: qcom: document sda660 SoC and ifc6560 board Dmitry Baryshkov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220513234518.3068480-1-dmitry.baryshkov@linaro.org \
--to=dmitry.baryshkov@linaro.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@somainline.org \
--cc=krzk@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).