From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>,
Douglas Anderson <dianders@chromium.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Sasha Levin <sashal@kernel.org>,
agross@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org, linux-arm-msm@vger.kernel.org,
devicetree@vger.kernel.org
Subject: [PATCH AUTOSEL 5.18 25/49] arm64: dts: qcom: sc7280-idp: Configure CTS pin to bias-bus-hold for bluetooth
Date: Wed, 1 Jun 2022 09:51:49 -0400 [thread overview]
Message-ID: <20220601135214.2002647-25-sashal@kernel.org> (raw)
In-Reply-To: <20220601135214.2002647-1-sashal@kernel.org>
From: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
[ Upstream commit 497b272759986af1aa5a25b5e903d082c67bd8f6 ]
WLAN rail was leaking power during RBSC/sleep even after turning BT off.
Change active and sleep pinctrl configurations to handle same.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1650556567-4995-2-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 18 ++++++++++++------
1 file changed, 12 insertions(+), 6 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index ecbf2b89d896..5ab3696af354 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -400,10 +400,13 @@ &qup_uart5_rx {
&qup_uart7_cts {
/*
- * Configure a pull-down on CTS to match the pull of
- * the Bluetooth module.
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
*/
- bias-pull-down;
+ bias-bus-hold;
};
&qup_uart7_rts {
@@ -495,10 +498,13 @@ qup_uart7_sleep_cts: qup-uart7-sleep-cts {
pins = "gpio28";
function = "gpio";
/*
- * Configure a pull-down on CTS to match the pull of
- * the Bluetooth module.
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
*/
- bias-pull-down;
+ bias-bus-hold;
};
qup_uart7_sleep_rts: qup-uart7-sleep-rts {
--
2.35.1
next prev parent reply other threads:[~2022-06-01 13:54 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20220601135214.2002647-1-sashal@kernel.org>
2022-06-01 13:51 ` [PATCH AUTOSEL 5.18 03/49] ARM: dts: ox820: align interrupt controller node name with dtschema Sasha Levin
2022-06-01 13:51 ` [PATCH AUTOSEL 5.18 04/49] ARM: dts: socfpga: " Sasha Levin
2022-06-01 13:51 ` [PATCH AUTOSEL 5.18 05/49] ARM: dts: s5pv210: align DMA channels " Sasha Levin
2022-06-01 13:51 ` [PATCH AUTOSEL 5.18 07/49] arm64: dts: qcom: msm8994: Fix the cont_splash_mem address Sasha Levin
2022-06-01 13:51 ` [PATCH AUTOSEL 5.18 08/49] arm64: dts: qcom: msm8994: Fix BLSP[12]_DMA channels count Sasha Levin
2022-06-01 13:51 ` [PATCH AUTOSEL 5.18 14/49] arm64: dts: qcom: sdm845-xiaomi-beryllium: fix typo in panel's vddio-supply property Sasha Levin
2022-06-01 13:51 ` [PATCH AUTOSEL 5.18 24/49] ARM: dts: exynos: add atmel,24c128 fallback to Samsung EEPROM Sasha Levin
2022-06-01 13:51 ` Sasha Levin [this message]
2022-06-01 13:51 ` [PATCH AUTOSEL 5.18 26/49] arm64: dts: qcom: sc7280-qcard: Configure CTS pin to bias-bus-hold for bluetooth Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220601135214.2002647-25-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=quic_vnivarth@quicinc.com \
--cc=robh+dt@kernel.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).