[PATCH 09/11] spi: dw: prepare the transfer routine for enhanced mode

[Sudip Mukherjee <sudip.mukherjee@sifive.com>]

The transfer routine of dual/quad/octal is similar to standard SPI mode
except that we do not need to worry about CS being de-asserted and we
will be writing the address to a single FIFO location.

Signed-off-by: Sudip Mukherjee <sudip.mukherjee@sifive.com>
---
 drivers/spi/spi-dw-core.c | 141 +++++++++++++++++++++++++++++++++-----
 1 file changed, 125 insertions(+), 16 deletions(-)

diff --git a/drivers/spi/spi-dw-core.c b/drivers/spi/spi-dw-core.c
index 2564a2276572..d6afa75e7023 100644
--- a/drivers/spi/spi-dw-core.c
+++ b/drivers/spi/spi-dw-core.c
@@ -712,6 +712,28 @@ static int dw_spi_wait_mem_op_done(struct dw_spi *dws)
 	return 0;
 }
 
+static void ext_transfer_delay(struct dw_spi *dws)
+{
+	struct spi_delay delay;
+	unsigned long ns, us;
+	u32 nents;
+
+	nents = dw_readl(dws, DW_SPI_TXFLR);
+	ns = NSEC_PER_SEC / dws->current_freq * nents;
+	ns *= dws->n_bytes * BITS_PER_BYTE;
+	if (ns <= NSEC_PER_USEC) {
+		delay.unit = SPI_DELAY_UNIT_NSECS;
+		delay.value = ns;
+	} else {
+		us = DIV_ROUND_UP(ns, NSEC_PER_USEC);
+		delay.unit = SPI_DELAY_UNIT_USECS;
+		delay.value = clamp_val(us, 0, USHRT_MAX);
+	}
+	/* wait until there is some space in TX FIFO */
+	while (!(dw_readl(dws, DW_SPI_SR) & DW_SPI_SR_TF_NOT_FULL))
+		spi_delay_exec(&delay, NULL);
+}
+
 static void dw_spi_stop_mem_op(struct dw_spi *dws, struct spi_device *spi)
 {
 	dw_spi_enable_chip(dws, 0);
@@ -719,6 +741,82 @@ static void dw_spi_stop_mem_op(struct dw_spi *dws, struct spi_device *spi)
 	dw_spi_enable_chip(dws, 1);
 }
 
+static int enhanced_transfer(struct dw_spi *dws, struct spi_device *spi,
+			     const struct spi_mem_op *op)
+{
+	u32 max, txw = 0, rxw;
+	bool cs_done = false;
+	void *buf = dws->tx;
+	int ret;
+
+	/* Send cmd as 32 bit value */
+	if (buf) {
+		txw = *(u32 *)(buf);
+		dw_write_io_reg(dws, DW_SPI_DR, txw);
+		buf += 4;
+		dws->tx_len--;
+		if (op->addr.nbytes) {
+			/*
+			 * Send address as 32 bit value if address
+			 * is present in the instruction.
+			 */
+			txw = *(u32 *)(buf);
+			dw_write_io_reg(dws, DW_SPI_DR, txw);
+			buf += 4;
+			dws->tx_len--;
+		}
+	}
+
+	do {
+		max = min_t(u32, dws->tx_len, dws->fifo_len -
+			    dw_readl(dws, DW_SPI_TXFLR));
+		while (max--) {
+			if (buf) {
+				txw = *(u8 *)(buf);
+				buf += dws->n_bytes;
+			}
+			dw_write_io_reg(dws, DW_SPI_DR, txw);
+			--dws->tx_len;
+		}
+		/* Enable CS after filling up FIFO */
+		if (!cs_done) {
+			dw_spi_set_cs(spi, false);
+			cs_done = true;
+		}
+		ext_transfer_delay(dws);
+		if (!dws->tx_len && !dws->rx_len) {
+			/*
+			 * We only need to wait for done if there is
+			 * nothing to receive and there is nothing more
+			 * to transmit. If we are receiving, then the
+			 * wait cycles will make sure we wait.
+			 */
+			ret = dw_spi_wait_mem_op_done(dws);
+			if (ret)
+				return ret;
+		}
+	} while (dws->tx_len);
+
+	buf = dws->rx;
+	while (dws->rx_len) {
+		max = dw_spi_rx_max(dws);
+
+		while (max--) {
+			rxw = dw_read_io_reg(dws, DW_SPI_DR);
+			if (buf) {
+				*(u8 *)(buf) = rxw;
+				buf += dws->n_bytes;
+			}
+			--dws->rx_len;
+		}
+
+		ret = dw_spi_check_status(dws, true);
+		if (ret)
+			return ret;
+	}
+	return 0;
+}
+
 static void update_spi_ctrl0(struct dw_spi *dws, const struct spi_mem_op *op, bool enable)
 {
 	u32 spi_ctrlr0;
@@ -846,25 +944,36 @@ static int dw_spi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
 	 * manually restricting the SPI bus frequency using the
 	 * dws->max_mem_freq parameter.
 	 */
-	local_irq_save(flags);
-	preempt_disable();
+	if (!enhanced_spi) {
+		local_irq_save(flags);
+		preempt_disable();
 
-	ret = dw_spi_write_then_read(dws, mem->spi);
+		ret = dw_spi_write_then_read(dws, mem->spi);
 
-	local_irq_restore(flags);
-	preempt_enable();
+		local_irq_restore(flags);
+		preempt_enable();
 
-	/*
-	 * Wait for the operation being finished and check the controller
-	 * status only if there hasn't been any run-time error detected. In the
-	 * former case it's just pointless. In the later one to prevent an
-	 * additional error message printing since any hw error flag being set
-	 * would be due to an error detected on the data transfer.
-	 */
-	if (!ret) {
-		ret = dw_spi_wait_mem_op_done(dws);
-		if (!ret)
-			ret = dw_spi_check_status(dws, true);
+		/*
+		 * Wait for the operation being finished and check the
+		 * controller status only if there hasn't been any
+		 * run-time error detected. In the former case it's
+		 * just pointless. In the later one to prevent an
+		 * additional error message printing since any hw error
+		 * flag being set would be due to an error detected on
+		 * the data transfer.
+		 */
+		if (!ret) {
+			ret = dw_spi_wait_mem_op_done(dws);
+			if (!ret)
+				ret = dw_spi_check_status(dws, true);
+		}
+	} else {
+		/*
+		 * We donot need to disable IRQs as clock stretching will
+		 * be enabled in enhanced mode which will prevent CS
+		 * from being de-assert.
+		 */
+		ret = enhanced_transfer(dws, mem->spi, op);
 	}
 
 	dw_spi_stop_mem_op(dws, mem->spi);
-- 
2.30.2