Re: [PATCH v2 3/6] arm64: dts: ls2080a-rdb: add phy nodes

[Shawn Guo <shawnguo@kernel.org>]

On Wed, Aug 17, 2022 at 03:43:54PM -0500, Li Yang wrote:
> Define PHY nodes on the board.
> 
> Signed-off-by: Li Yang <leoyang.li@nxp.com>
> ---
>  .../boot/dts/freescale/fsl-ls2080a-rdb.dts    | 68 +++++++++++++++++++
>  1 file changed, 68 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
> index 44894356059c..fec02fd754be 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
> @@ -23,3 +23,71 @@ chosen {
>  		stdout-path = "serial1:115200n8";
>  	};
>  };
> +
> +&dpmac5 {
> +	phy-handle = <&mdio2_phy1>;
> +	phy-connection-type = "10gbase-r";
> +};
> +
> +&dpmac6 {
> +	phy-handle = <&mdio2_phy2>;
> +	phy-connection-type = "10gbase-r";
> +};
> +
> +&dpmac7 {
> +	phy-handle = <&mdio2_phy3>;
> +	phy-connection-type = "10gbase-r";
> +};
> +
> +&dpmac8 {
> +	phy-handle = <&mdio2_phy4>;
> +	phy-connection-type = "10gbase-r";
> +};
> +
> +&emdio1 {
> +	status = "disabled";
> +
> +	/* CS4340 PHYs */
> +	mdio1_phy1: emdio1-phy@1 {
> +		reg = <0x10>;

unit-address doesn't match 'reg'.

> +	};
> +
> +	mdio1_phy2: emdio1-phy@2 {
> +		reg = <0x11>;
> +	};
> +
> +	mdio1_phy3: emdio1-phy@3 {
> +		reg = <0x12>;
> +	};
> +
> +	mdio1_phy4: emdio1-phy@4 {
> +		reg = <0x13>;
> +	};
> +};
> +
> +&emdio2 {
> +	/* AQR405 PHYs */
> +	mdio2_phy1: emdio2-phy@1 {
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		interrupts = <0 1 0x4>; /* Level high type */

What does '0' mean here?  And why not IRQ_TYPE_LEVEL_HIGH for polarity
cell?

Shawn

> +		reg = <0x0>;
> +	};
> +
> +	mdio2_phy2: emdio2-phy@2 {
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		interrupts = <0 2 0x4>; /* Level high type */
> +		reg = <0x1>;
> +	};
> +
> +	mdio2_phy3: emdio2-phy@3 {
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		interrupts = <0 4 0x4>; /* Level high type */
> +		reg = <0x2>;
> +	};
> +
> +	mdio2_phy4: emdio2-phy@4 {
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		interrupts = <0 5 0x4>; /* Level high type */
> +		reg = <0x3>;
> +	};
> +};
> -- 
> 2.37.1
>