Devicetree
 help / color / mirror / Atom feed
From: Serge Semin <fancer.lancer@gmail.com>
To: Sudip Mukherjee <sudip.mukherjee@sifive.com>
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>,
	Mark Brown <broonie@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	greentime.hu@sifive.com, jude.onyenegecha@sifive.com,
	william.salmon@sifive.com, adnan.chowdhury@sifive.com,
	ben.dooks@sifive.com, linux-spi@vger.kernel.org,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	jeegar.lakhani@sifive.com
Subject: Re: [PATCH 05/11] spi: dw: define SPI_CTRLR0 register and its fields
Date: Sat, 27 Aug 2022 01:19:23 +0300	[thread overview]
Message-ID: <20220826221923.k4cwharkathma7zi@mobilestation> (raw)
In-Reply-To: <20220802175755.6530-6-sudip.mukherjee@sifive.com>

On Tue, Aug 02, 2022 at 06:57:49PM +0100, Sudip Mukherjee wrote:
> Synopsys SSI controllers supporting enhanced SPI mode of operation has
> SPI Control Register at offset 0xf4 which controls the following:
> 
> CLK_STRETCH_EN: Enables clock stretching capability in SPI transfers.
> In case of write, if the FIFO becomes empty DWC_ssi will stretch the
> clock until FIFO has enough data to continue the transfer. In case of
> read, if the receive FIFO becomes full DWC_ssi will stop the clock until
> data has been read from the FIFO.
> 
> WAIT_CYCLES: Wait cycles in Dual/Quad/Octal mode between control frames
> transmit and data reception.
> 
> INST_L: Dual/Quad/Octal mode instruction length in bits.
> 
> ADDR_L: defines Length of Address to be transmitted.
> 
> For now, we are only using 32bit Address length and 8 bit Instruction
> length.
> 
> Signed-off-by: Sudip Mukherjee <sudip.mukherjee@sifive.com>
> ---
>  drivers/spi/spi-dw.h | 11 +++++++++++
>  1 file changed, 11 insertions(+)
> 
> diff --git a/drivers/spi/spi-dw.h b/drivers/spi/spi-dw.h
> index b8cc20e0deaa..a7a4637d6d32 100644
> --- a/drivers/spi/spi-dw.h
> +++ b/drivers/spi/spi-dw.h
> @@ -63,6 +63,17 @@
>  #define DW_SPI_RX_SAMPLE_DLY		0xf0
>  #define DW_SPI_CS_OVERRIDE		0xf4
>  

> +/* Register offsets (Defined in DWC SSI 1.03a) */

Drop this comment. The CSR can exist in the DW APB SSI too

> +#define DW_HSSI_SPI_CTRLR0		0xf4

#define DW_SSI_SPI_CTRLR0		0xf4

> +
> +/* Bit fields in SPI_CTRLR0 (Defined in DWC SSI 1.03a) */

Drop the IP-core ID and version from the comment. As I said the eSPI
feature can be enabled for DW APB SSI too.

> +#define DW_HSSI_SPI_CTRLR0_CLK_STRETCH_EN	BIT(30)
> +#define DW_HSSI_SPI_CTRLR0_WAIT_CYCLE_MASK	GENMASK(15, 11)
> +#define DW_HSSI_SPI_CTRLR0_INST_L_MASK		GENMASK(9, 8)
> +#define DW_HSSI_SPI_CTRLR0_INST_L8		0x2
> +#define DW_HSSI_SPI_CTRLR0_ADDR_L_MASK		GENMASK(5, 2)
> +#define DW_HSSI_SPI_CTRLR0_ADDR_L32		0x8

Move this to the tail of the CSR fields macros definition (right after
the DW_SPI_DMACR_TDMAE macros) and s/HSSI/SPI .

-Sergey

> +
>  /* Bit fields in CTRLR0 (DWC APB SSI) */
>  #define DW_PSSI_CTRLR0_DFS_MASK			GENMASK(3, 0)
>  #define DW_PSSI_CTRLR0_DFS32_MASK		GENMASK(20, 16)
> -- 
> 2.30.2
> 

  reply	other threads:[~2022-08-26 22:22 UTC|newest]

Thread overview: 37+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-08-02 17:57 [PATCH 00/11] Add support for enhanced SPI for Designware SPI controllers Sudip Mukherjee
2022-08-02 17:57 ` [PATCH 01/11] spi: dw: define capability for enhanced spi Sudip Mukherjee
2022-08-02 18:47   ` Mark Brown
2022-08-03 17:34     ` Sudip Mukherjee
2022-08-03 17:40       ` Mark Brown
2022-08-26 18:16   ` Serge Semin
2022-08-02 17:57 ` [PATCH 02/11] spi: dw: add check for support of dual/quad/octal Sudip Mukherjee
2022-08-26 21:36   ` Serge Semin
2022-08-02 17:57 ` [PATCH 03/11] spi: dw: define spi_frf for dual/quad/octal modes Sudip Mukherjee
2022-08-26 22:03   ` Serge Semin
2022-08-26 22:22     ` Serge Semin
2022-08-02 17:57 ` [PATCH 04/11] spi: dw: use TMOD_RO to read in enhanced spi modes Sudip Mukherjee
2022-08-02 19:13   ` Mark Brown
2022-08-03 17:35     ` Sudip Mukherjee
2022-08-26 22:12   ` Serge Semin
2022-08-02 17:57 ` [PATCH 05/11] spi: dw: define SPI_CTRLR0 register and its fields Sudip Mukherjee
2022-08-26 22:19   ` Serge Semin [this message]
2022-08-02 17:57 ` [PATCH 06/11] spi: dw: update SPI_CTRLR0 register Sudip Mukherjee
2022-08-26 22:50   ` Serge Semin
2022-08-02 17:57 ` [PATCH 07/11] spi: dw: update NDF while writing in enhanced spi mode Sudip Mukherjee
2022-08-26 22:54   ` Serge Semin
2022-08-02 17:57 ` [PATCH 08/11] spi: dw: update buffer for " Sudip Mukherjee
2022-08-26 23:05   ` Serge Semin
2022-08-02 17:57 ` [PATCH 09/11] spi: dw: prepare the transfer routine for enhanced mode Sudip Mukherjee
2022-08-26 23:19   ` Serge Semin
2022-08-02 17:57 ` [PATCH 10/11] spi: dw-apb-ssi: add generic 1.03a version Sudip Mukherjee
2022-08-03  6:35   ` Krzysztof Kozlowski
2022-08-26 23:23   ` Serge Semin
2022-08-26 23:33   ` Serge Semin
2022-08-02 17:57 ` [PATCH 11/11] spi: dw: initialize dwc-ssi-1.03a controller Sudip Mukherjee
2022-08-26 23:31   ` Serge Semin
2022-08-03 18:56 ` [PATCH 00/11] Add support for enhanced SPI for Designware SPI controllers Serge Semin
2022-08-04  9:43   ` Sudip Mukherjee
2022-08-21 20:37 ` Serge Semin
2022-08-26 18:03 ` Serge Semin
2022-08-30  8:48   ` Sudip Mukherjee
2022-09-02 23:03     ` Serge Semin

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220826221923.k4cwharkathma7zi@mobilestation \
    --to=fancer.lancer@gmail.com \
    --cc=Sergey.Semin@baikalelectronics.ru \
    --cc=adnan.chowdhury@sifive.com \
    --cc=ben.dooks@sifive.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=greentime.hu@sifive.com \
    --cc=jeegar.lakhani@sifive.com \
    --cc=jude.onyenegecha@sifive.com \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=sudip.mukherjee@sifive.com \
    --cc=william.salmon@sifive.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox