[PATCH 08/23] ARM: dts: qcom: apq8064-cm-qs600: use labels to patch device tree

[Dmitry Baryshkov <dmitry.baryshkov@linaro.org>]

Use labels to add device-specific properties to DT nodes rather than
duplicating SoC DT structure in the device DT.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts | 372 ++++++++++----------
 1 file changed, 183 insertions(+), 189 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
index 529629a0a9dc..65684da52e2e 100644
--- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
@@ -30,217 +30,211 @@ sdcc4_pwrseq: sdcc4_pwrseq {
 	};
 
 	soc {
-		pinctrl@800000 {
-			card_detect: card_detect {
-				mux {
-					pins = "gpio26";
-					function = "gpio";
-					bias-disable;
-				};
-			};
-
-			pcie_pins: pcie_pinmux {
-				mux {
-					pins = "gpio27";
-					function = "gpio";
-				};
-				conf {
-					pins = "gpio27";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
+		/* on board fixed 3.3v supply */
+		v3p3_fixed: v3p3 {
+			compatible = "regulator-fixed";
+			regulator-name = "PCIE V3P3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
 		};
 
-		rpm@108000 {
-			regulators {
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s1>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				s4 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3050000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1700000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				pm8921_lvs6: lvs6 {
-					bias-pull-down;
-				};
-
-			};
-		};
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
 
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
+&gsbi1_i2c {
+	clock-frequency = <200000>;
+	status = "okay";
 
-			i2c@12460000 {
-				status = "okay";
-				clock-frequency = <200000>;
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
 
-				eeprom@50 {
-					compatible = "atmel,24c02";
-					reg = <0x50>;
-					pagesize = <32>;
-				};
-			};
+&gsbi7_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi7_uart_2pins>;
+	status = "okay";
+};
+
+&pcie {
+	vdda-supply = <&pm8921_s3>;
+	vdda_phy-supply = <&pm8921_lvs6>;
+	vdda_refclk-supply = <&v3p3_fixed>;
+	pinctrl-0 = <&pcie_pins>;
+	pinctrl-names = "default";
+	perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pm8921_gpio {
+	wlan_default_gpios: wlan-gpios-state {
+		pinconf {
+			pins = "gpio43";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
 		};
+	};
+};
+
+&rpm {
+	regulators {
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
 
-		gsbi@16600000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi7_uart_2pins>;
-			};
+
+		/* Buck SMPS */
+		s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
 		};
 
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
+		s3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <4800000>;
 		};
 
-		usb@12520000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
+		s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		usb@12530000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
+		s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		/* on board fixed 3.3v supply */
-		v3p3_fixed: v3p3 {
-			compatible = "regulator-fixed";
-			regulator-name = "PCIE V3P3";
-			regulator-min-microvolt = <3300000>;
+		l3 {
+			regulator-min-microvolt = <3050000>;
 			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
+			bias-pull-down;
 		};
 
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					wlan_default_gpios: wlan-gpios-state {
-						pinconf {
-							pins = "gpio43";
-							function = "normal";
-							bias-disable;
-							power-source = <PM8921_GPIO_S4>;
-						};
-					};
-				};
-			};
+		l4 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
 		};
 
-		pci@1b500000 {
-			status = "okay";
-			vdda-supply = <&pm8921_s3>;
-			vdda_phy-supply = <&pm8921_lvs6>;
-			vdda_refclk-supply = <&v3p3_fixed>;
-			pinctrl-0 = <&pcie_pins>;
-			pinctrl-names = "default";
-			perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+		l5 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		l23 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
 		};
 
-		amba {
-			/* eMMC */
-			sdcc1: mmc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			/* External micro SD card */
-			sdcc3: mmc@12180000 {
-				status = "okay";
-				vmmc-supply = <&v3p3_fixed>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&card_detect>;
-				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-			};
-			/* WLAN */
-			sdcc4: mmc@121c0000 {
-				status = "okay";
-				vmmc-supply = <&v3p3_fixed>;
-				vqmmc-supply = <&v3p3_fixed>;
-				mmc-pwrseq = <&sdcc4_pwrseq>;
-			};
+		lvs6 {
+			bias-pull-down;
+		};
+
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&v3p3_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&card_detect>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* WLAN */
+&sdcc4 {
+	status = "okay";
+	vmmc-supply = <&v3p3_fixed>;
+	vqmmc-supply = <&v3p3_fixed>;
+	mmc-pwrseq = <&sdcc4_pwrseq>;
+};
+
+&tlmm_pinmux {
+	card_detect: card_detect {
+		mux {
+			pins = "gpio26";
+			function = "gpio";
+			bias-disable;
 		};
 	};
+
+	pcie_pins: pcie_pinmux {
+		mux {
+			pins = "gpio27";
+			function = "gpio";
+		};
+		conf {
+			pins = "gpio27";
+			drive-strength = <12>;
+			bias-disable;
+		};
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb_hs3_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+&usb_hs4_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb4 {
+	dr_mode = "host";
+	status = "okay";
 };
-- 
2.35.1