[PATCH AUTOSEL 6.0 01/46] arm64: dts: qcom: sdm845: narrow LLCC address space

[PATCH AUTOSEL 6.0 01/46] arm64: dts: qcom: sdm845: narrow LLCC address space

[Sasha Levin]

From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

[ Upstream commit 300b5f661eebefb8571841b78091343eb87eca54 ]

The Last Level Cache Controller (LLCC) device does not need to access
entire LLCC address space.  Currently driver uses only hardware info and
status registers which both reside in LLCC0_COMMON range (offset
0x30000, size 0x1000).  Narrow the address space to allow binding other
drivers to rest of LLCC address space.

Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Reported-by: Steev Klimaszewski <steev@kali.org>
Suggested-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220728113748.170548-11-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index f0e286715d1b..4d5ae5897d1d 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -2138,7 +2138,7 @@ uart15: serial@a9c000 {
 
 		llcc: system-cache-controller@1100000 {
 			compatible = "qcom,sdm845-llcc";
-			reg = <0 0x01100000 0 0x200000>, <0 0x01300000 0 0x50000>;
+			reg = <0 0x01100000 0 0x31000>, <0 0x01300000 0 0x50000>;
 			reg-names = "llcc_base", "llcc_broadcast_base";
 			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
 		};
-- 
2.35.1

[PATCH AUTOSEL 6.0 02/46] ARM: dts: imx6: delete interrupts property if interrupts-extended is set

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit c9d38ff7080b2c4fa6786b82210fa13115895aae ]

In most cases this is related to fsl,err006687-workaround-present, which
requires a GPIO interrupt next a GIC interrupt.

This fixes the dtbs_check warning:
imx6dl-mba6a.dtb: ethernet@2188000: More than one condition true in oneOf schema:
        {'$filename': 'Documentation/devicetree/bindings/net/fsl,fec.yaml',
[...]

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6dl-riotboard.dts        | 1 +
 arch/arm/boot/dts/imx6q-arm2.dts              | 1 +
 arch/arm/boot/dts/imx6q-evi.dts               | 1 +
 arch/arm/boot/dts/imx6q-mccmon6.dts           | 1 +
 arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi      | 1 +
 arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi  | 1 +
 arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi | 1 +
 arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi     | 1 +
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi      | 1 +
 arch/arm/boot/dts/imx6qdl-tqma6a.dtsi         | 1 +
 arch/arm/boot/dts/imx6qdl-ts7970.dtsi         | 1 +
 11 files changed, 11 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
index e7d9bfbfd0e4..e7be05f205d3 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
@@ -90,6 +90,7 @@ &fec {
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
 	phy-handle = <&rgmii_phy>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6q-arm2.dts b/arch/arm/boot/dts/imx6q-arm2.dts
index 0b40f52268b3..75586299d9ca 100644
--- a/arch/arm/boot/dts/imx6q-arm2.dts
+++ b/arch/arm/boot/dts/imx6q-arm2.dts
@@ -178,6 +178,7 @@ &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
index c63f371ede8b..78d941fef5df 100644
--- a/arch/arm/boot/dts/imx6q-evi.dts
+++ b/arch/arm/boot/dts/imx6q-evi.dts
@@ -146,6 +146,7 @@ &fec {
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6q-mccmon6.dts b/arch/arm/boot/dts/imx6q-mccmon6.dts
index 55692c73943d..64ab01018b71 100644
--- a/arch/arm/boot/dts/imx6q-mccmon6.dts
+++ b/arch/arm/boot/dts/imx6q-mccmon6.dts
@@ -100,6 +100,7 @@ &fec {
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
index 0ad4cb4f1e82..a53a5d0766a5 100644
--- a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
@@ -192,6 +192,7 @@ &fec {
 	phy-mode = "rgmii";
 	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
index beaa2dcd436c..57c21a01f126 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
@@ -334,6 +334,7 @@ &fec {
 	phy-mode = "rgmii";
 	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi
index ee7e2371f94b..000e9dc97b1a 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi
@@ -263,6 +263,7 @@ &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
index 904d5d051d63..731759bdd7f5 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
@@ -267,6 +267,7 @@ &fec {
 	phy-mode = "rgmii";
 	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 1368a4762037..3dbb460ef102 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -295,6 +295,7 @@ &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-tqma6a.dtsi b/arch/arm/boot/dts/imx6qdl-tqma6a.dtsi
index 7dc3f0005b0f..0a36e1bce375 100644
--- a/arch/arm/boot/dts/imx6qdl-tqma6a.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tqma6a.dtsi
@@ -7,6 +7,7 @@
 #include <dt-bindings/gpio/gpio.h>
 
 &fec {
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-ts7970.dtsi b/arch/arm/boot/dts/imx6qdl-ts7970.dtsi
index d6ba4b2a60f6..c096d25a6f5b 100644
--- a/arch/arm/boot/dts/imx6qdl-ts7970.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-ts7970.dtsi
@@ -192,6 +192,7 @@ &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
-- 
2.35.1

[PATCH AUTOSEL 6.0 03/46] ARM: dts: imx7d-sdb: config the max pressure for tsc2046

[Sasha Levin]

From: Haibo Chen <haibo.chen@nxp.com>

[ Upstream commit e7c4ebe2f9cd68588eb24ba4ed122e696e2d5272 ]

Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,

[17:19:39.183] event1  - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1  - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1  - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1  - not using input device '/dev/input/event1'

This will then cause the APP weston-touch-calibrator can't list touch devices.

root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.

And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx7d-sdb.dts | 7 +------
 1 file changed, 1 insertion(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 78f4224a9bf4..e93b9cd9c27b 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -206,12 +206,7 @@ tsc2046@0 {
 		interrupt-parent = <&gpio2>;
 		interrupts = <29 0>;
 		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
-		ti,x-min = /bits/ 16 <0>;
-		ti,x-max = /bits/ 16 <0>;
-		ti,y-min = /bits/ 16 <0>;
-		ti,y-max = /bits/ 16 <0>;
-		ti,pressure-max = /bits/ 16 <0>;
-		ti,x-plate-ohms = /bits/ 16 <400>;
+		touchscreen-max-pressure = <255>;
 		wakeup-source;
 	};
 };
-- 
2.35.1

[PATCH AUTOSEL 6.0 05/46] arm64: dts: qcom: sc7280-idp: correct ADC channel node name and unit address

[Sasha Levin]

From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

[ Upstream commit 5589ffb2da2a66988ab3a68334dad3e68b42e3a9 ]

Correct SPMI PMIC VADC channel node name:
1. Use hyphens instead of underscores,
2. Add missing unit address.

This fixes `make dtbs_check` warnings like:

  qcom/sc7280-idp.dtb: pmic@0: adc@3100: 'pmk8350_die_temp', 'pmr735a_die_temp' do not match any of the regexes: '^.*@[0-9a-f]+$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220828084341.112146-12-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dts  | 2 +-
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 6d3ff80582ae..e2e37a0292ad 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -78,7 +78,7 @@ &nvme_3v3_regulator {
 };
 
 &pmk8350_vadc {
-	pmr735a_die_temp {
+	pmr735a-die-temp@403 {
 		reg = <PMR735A_ADC7_DIE_TEMP>;
 		label = "pmr735a_die_temp";
 		qcom,pre-scaling = <1 1>;
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index a74e0b730db6..27c47ddbdf02 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -264,7 +264,7 @@ &pcie1_phy {
 };
 
 &pmk8350_vadc {
-	pmk8350_die_temp {
+	pmk8350-die-temp@3 {
 		reg = <PMK8350_ADC7_DIE_TEMP>;
 		label = "pmk8350_die_temp";
 		qcom,pre-scaling = <1 1>;
-- 
2.35.1

[PATCH AUTOSEL 6.0 06/46] ARM: dts: imx6q: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit b11d083c5dcec7c42fe982c854706d404ddd3a5f ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6q.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index 3b77eae40e39..df86049a695b 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -163,6 +163,9 @@ soc: soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x40000>;
+			ranges = <0 0x00900000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 6.0 07/46] ARM: dts: imx6dl: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit f5848b95633d598bacf0500e0108dc5961af88c0 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6dl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index 8e0ed209ede0..dc919e09a505 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -84,6 +84,9 @@ soc: soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 6.0 08/46] ARM: dts: imx6qp: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 088fe5237435ee2f7ed4450519b2ef58b94c832f ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property
sram@940000: '#size-cells' is a required property
sram@940000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qp.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qp.dtsi b/arch/arm/boot/dts/imx6qp.dtsi
index 050365513836..fc164991d2ae 100644
--- a/arch/arm/boot/dts/imx6qp.dtsi
+++ b/arch/arm/boot/dts/imx6qp.dtsi
@@ -9,12 +9,18 @@ soc {
 		ocram2: sram@940000 {
 			compatible = "mmio-sram";
 			reg = <0x00940000 0x20000>;
+			ranges = <0 0x00940000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
 		ocram3: sram@960000 {
 			compatible = "mmio-sram";
 			reg = <0x00960000 0x20000>;
+			ranges = <0 0x00960000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 6.0 09/46] ARM: dts: imx6sl: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 60c9213a1d9941a8b33db570796c3f9be8984974 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi
index 06a515121dfc..cfd6b4972ae7 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/imx6sl.dtsi
@@ -115,6 +115,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 6.0 10/46] ARM: dts: imx6sll: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 7492a83ed9b7a151e2dd11d64b06da7a7f0fa7f9 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sll.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi
index d4a000c3dde7..2873369a57c0 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/imx6sll.dtsi
@@ -115,6 +115,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		intc: interrupt-controller@a01000 {
-- 
2.35.1

[PATCH AUTOSEL 6.0 11/46] ARM: dts: imx6sx: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 415432c008b2bce8138841356ba444631cabaa50 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sx.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
index 4d075e2bf749..2611eef3b2a2 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/imx6sx.dtsi
@@ -164,12 +164,18 @@ soc: soc {
 		ocram_s: sram@8f8000 {
 			compatible = "mmio-sram";
 			reg = <0x008f8000 0x4000>;
+			ranges = <0 0x008f8000 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM_S>;
 		};
 
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 6.0 12/46] ARM: dts: imx6sl: use tabs for code indent

[Sasha Levin]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

[ Upstream commit 218db824a7519856d0eaaeb5c41ca504ed550210 ]

This fixes the following error:

arch/arm/boot/dts/imx6sl.dtsi:714: error: code indent should use tabs
where possible

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sl.dtsi | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi
index cfd6b4972ae7..01122ddfdc0d 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/imx6sl.dtsi
@@ -61,10 +61,10 @@ cpu0: cpu@0 {
 				<792000  1175000>,
 				<396000  975000>;
 			fsl,soc-operating-points =
-				/* ARM kHz      SOC-PU uV */
-				<996000         1225000>,
-				<792000         1175000>,
-				<396000         1175000>;
+				/* ARM kHz	SOC-PU uV */
+				<996000		1225000>,
+				<792000		1175000>,
+				<396000		1175000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
 			clocks = <&clks IMX6SL_CLK_ARM>, <&clks IMX6SL_CLK_PLL2_PFD2>,
@@ -225,7 +225,7 @@ ecspi4: spi@2014000 {
 
 				uart5: serial@2018000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02018000 0x4000>;
 					interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -238,7 +238,7 @@ uart5: serial@2018000 {
 
 				uart1: serial@2020000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02020000 0x4000>;
 					interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -251,7 +251,7 @@ uart1: serial@2020000 {
 
 				uart2: serial@2024000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02024000 0x4000>;
 					interrupts = <0 27 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -312,7 +312,7 @@ ssi3: ssi@2030000 {
 
 				uart3: serial@2034000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02034000 0x4000>;
 					interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -325,7 +325,7 @@ uart3: serial@2034000 {
 
 				uart4: serial@2038000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02038000 0x4000>;
 					interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -714,7 +714,7 @@ pd_pu: power-domain@1 {
 						#power-domain-cells = <0>;
 						power-supply = <&reg_pu>;
 						clocks = <&clks IMX6SL_CLK_GPU2D_OVG>,
-						         <&clks IMX6SL_CLK_GPU2D_PODF>;
+							 <&clks IMX6SL_CLK_GPU2D_PODF>;
 					};
 
 					pd_disp: power-domain@2 {
-- 
2.35.1

[PATCH AUTOSEL 6.0 13/46] ARM: dts: imx6sx-udoo-neo: don't use multiple blank lines

[Sasha Levin]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

[ Upstream commit fd2dd7077c7498765e7326c1b7f34bde85f1a975 ]

This fixes the following warning:

arch/arm/boot/dts/imx6sx-udoo-neo.dtsi:309: check: Please don't use multiple
blank lines

While at it, use tabs indent for some pinctrl entries.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sx-udoo-neo.dtsi | 14 ++++++--------
 1 file changed, 6 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi b/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
index 35861bbea94e..c84ea1fac5e9 100644
--- a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
+++ b/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
@@ -226,7 +226,7 @@ lcdc: endpoint {
 &iomuxc {
 	pinctrl_bt_reg: btreggrp {
 		fsl,pins =
-			<MX6SX_PAD_KEY_ROW2__GPIO2_IO_17        0x15059>;
+			<MX6SX_PAD_KEY_ROW2__GPIO2_IO_17	0x15059>;
 	};
 
 	pinctrl_enet1: enet1grp {
@@ -306,7 +306,6 @@ MX6SX_PAD_LCD1_RESET__GPIO3_IO_27		0x4001b0b0
 		>;
 	};
 
-
 	pinctrl_uart1: uart1grp {
 		fsl,pins =
 			<MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX	0x1b0b1>,
@@ -347,24 +346,23 @@ pinctrl_uart6: uart6grp {
 
 	pinctrl_otg1_reg: otg1grp {
 		fsl,pins =
-			<MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9        0x10b0>;
+			<MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9	0x10b0>;
 	};
 
-
 	pinctrl_otg2_reg: otg2grp {
 		fsl,pins =
-			<MX6SX_PAD_NAND_RE_B__GPIO4_IO_12        0x10b0>;
+			<MX6SX_PAD_NAND_RE_B__GPIO4_IO_12	0x10b0>;
 	};
 
 	pinctrl_usb_otg1: usbotg1grp {
 		fsl,pins =
-			<MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID    0x17059>,
-			<MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC       0x10b0>;
+			<MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID	0x17059>,
+			<MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC	0x10b0>;
 	};
 
 	pinctrl_usb_otg2: usbot2ggrp {
 		fsl,pins =
-			<MX6SX_PAD_QSPI1A_DATA0__USB_OTG2_OC     0x10b0>;
+			<MX6SX_PAD_QSPI1A_DATA0__USB_OTG2_OC	0x10b0>;
 	};
 
 	pinctrl_usdhc2: usdhc2grp {
-- 
2.35.1

[PATCH AUTOSEL 6.0 19/46] arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card IO voltage

[Sasha Levin]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

[ Upstream commit eef2c0217e02b6c7ed5b10b82ea944127145e113 ]

It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.

Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.

Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts    | 3 +++
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 2 --
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index 23be1ec538ba..c54536c0a2ba 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -321,6 +321,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
 		>;
 	};
 
@@ -333,6 +334,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
 		>;
 	};
 
@@ -345,6 +347,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
 		>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 8f90eb02550d..6307af803429 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -86,7 +86,6 @@ pca9450: pmic@25 {
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 
 		regulators {
 			reg_vdd_soc: BUCK1 {
@@ -229,7 +228,6 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
-			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
 		>;
 	};
 
-- 
2.35.1

[PATCH AUTOSEL 6.0 20/46] arm64: dts: imx8ulp: no executable source file permission

[Sasha Levin]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

[ Upstream commit 7db9905d48e1b9a97a28224c5a201262ebce7489 ]

This fixes the following error:

arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h: error: do not set
 execute permissions for source files

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h | 0
 1 file changed, 0 insertions(+), 0 deletions(-)
 mode change 100755 => 100644 arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h

diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h b/arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h
old mode 100755
new mode 100644
-- 
2.35.1

[PATCH AUTOSEL 6.0 21/46] arm64: dts: imx8mq-librem5: Add bq25895 as max17055's power supply

[Sasha Levin]

From: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>

[ Upstream commit 6effe295e1a87408033c29dbcea9d5a5c8b937d5 ]

This allows the userspace to notice that there's not enough
current provided to charge the battery, and also fixes issues
with 0% SOC values being considered invalid.

Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
index 9eec8a7eecfc..127fc7f904c8 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
@@ -1077,6 +1077,7 @@ bat: fuel-gauge@36 {
 		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gauge>;
+		power-supplies = <&bq25895>;
 		maxim,over-heat-temp = <700>;
 		maxim,over-volt = <4500>;
 		maxim,rsns-microohm = <5000>;
-- 
2.35.1

[PATCH AUTOSEL 6.0 42/46] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Sasha Levin]

From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>

[ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]

PXs3 reference board can change each USB port 0 and 1 to device mode
with jumpers. Prepare devicetree sources for USB port 0 and 1.

This specifies dr_mode, pinctrl, and some quirks and removes nodes for
unused phys and vbus-supply properties.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-8-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/uniphier-pinctrl.dtsi       | 10 +++++
 arch/arm64/boot/dts/socionext/Makefile        |  4 +-
 .../socionext/uniphier-pxs3-ref-gadget0.dts   | 41 +++++++++++++++++++
 .../socionext/uniphier-pxs3-ref-gadget1.dts   | 40 ++++++++++++++++++
 4 files changed, 94 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
 create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts

diff --git a/arch/arm/boot/dts/uniphier-pinctrl.dtsi b/arch/arm/boot/dts/uniphier-pinctrl.dtsi
index c0fd029b37e5..f909ec2e5333 100644
--- a/arch/arm/boot/dts/uniphier-pinctrl.dtsi
+++ b/arch/arm/boot/dts/uniphier-pinctrl.dtsi
@@ -196,11 +196,21 @@ pinctrl_usb0: usb0 {
 		function = "usb0";
 	};
 
+	pinctrl_usb0_device: usb0-device {
+		groups = "usb0_device";
+		function = "usb0";
+	};
+
 	pinctrl_usb1: usb1 {
 		groups = "usb1";
 		function = "usb1";
 	};
 
+	pinctrl_usb1_device: usb1-device {
+		groups = "usb1_device";
+		function = "usb1";
+	};
+
 	pinctrl_usb2: usb2 {
 		groups = "usb2";
 		function = "usb2";
diff --git a/arch/arm64/boot/dts/socionext/Makefile b/arch/arm64/boot/dts/socionext/Makefile
index dda3da33614b..33989a9643ac 100644
--- a/arch/arm64/boot/dts/socionext/Makefile
+++ b/arch/arm64/boot/dts/socionext/Makefile
@@ -5,4 +5,6 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \
 	uniphier-ld20-akebi96.dtb \
 	uniphier-ld20-global.dtb \
 	uniphier-ld20-ref.dtb \
-	uniphier-pxs3-ref.dtb
+	uniphier-pxs3-ref.dtb \
+	uniphier-pxs3-ref-gadget0.dtb \
+	uniphier-pxs3-ref-gadget1.dtb
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
new file mode 100644
index 000000000000..7069f51bc120
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #0)
+//
+// Copyright (C) 2021 Socionext Inc.
+//   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+/dts-v1/;
+#include "uniphier-pxs3-ref.dts"
+
+/ {
+	model = "UniPhier PXs3 Reference Board (USB-Device #0)";
+};
+
+/* I2C3 pinctrl is shared with USB*VBUSIN */
+&i2c3 {
+	status = "disabled";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	pinctrl-0 = <&pinctrl_usb0_device>;
+	snps,dis_enblslpm_quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb2_gadget_lpm_disable;
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb0_hsphy0>, <&usb0_ssphy0>;
+};
+
+&usb0_hsphy0 {
+	/delete-property/ vbus-supply;
+};
+
+&usb0_ssphy0 {
+	/delete-property/ vbus-supply;
+};
+
+/delete-node/ &usb0_hsphy1;
+/delete-node/ &usb0_ssphy1;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
new file mode 100644
index 000000000000..a3cfa8113ffb
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #1)
+//
+// Copyright (C) 2021 Socionext Inc.
+//   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+/dts-v1/;
+#include "uniphier-pxs3-ref.dts"
+
+/ {
+	model = "UniPhier PXs3 Reference Board (USB-Device #1)";
+};
+
+/* I2C3 pinctrl is shared with USB*VBUSIN */
+&i2c3 {
+	status = "disabled";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "peripheral";
+	pinctrl-0 = <&pinctrl_usb1_device>;
+	snps,dis_enblslpm_quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb2_gadget_lpm_disable;
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb1_hsphy0>, <&usb1_ssphy0>;
+};
+
+&usb1_hsphy0 {
+	/delete-property/ vbus-supply;
+};
+
+&usb1_ssphy0 {
+	/delete-property/ vbus-supply;
+};
+
+/delete-node/ &usb1_hsphy1;
-- 
2.35.1