[PATCH AUTOSEL 5.15 01/26] arm64: dts: qcom: sdm845: narrow LLCC address space

[PATCH AUTOSEL 5.15 01/26] arm64: dts: qcom: sdm845: narrow LLCC address space

[Sasha Levin]

From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

[ Upstream commit 300b5f661eebefb8571841b78091343eb87eca54 ]

The Last Level Cache Controller (LLCC) device does not need to access
entire LLCC address space.  Currently driver uses only hardware info and
status registers which both reside in LLCC0_COMMON range (offset
0x30000, size 0x1000).  Narrow the address space to allow binding other
drivers to rest of LLCC address space.

Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Reported-by: Steev Klimaszewski <steev@kali.org>
Suggested-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220728113748.170548-11-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index ea7a272d267a..ce523ec8dd28 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -1968,7 +1968,7 @@ uart15: serial@a9c000 {
 
 		system-cache-controller@1100000 {
 			compatible = "qcom,sdm845-llcc";
-			reg = <0 0x01100000 0 0x200000>, <0 0x01300000 0 0x50000>;
+			reg = <0 0x01100000 0 0x31000>, <0 0x01300000 0 0x50000>;
 			reg-names = "llcc_base", "llcc_broadcast_base";
 			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
 		};
-- 
2.35.1

[PATCH AUTOSEL 5.15 02/26] ARM: dts: imx7d-sdb: config the max pressure for tsc2046

[Sasha Levin]

From: Haibo Chen <haibo.chen@nxp.com>

[ Upstream commit e7c4ebe2f9cd68588eb24ba4ed122e696e2d5272 ]

Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,

[17:19:39.183] event1  - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1  - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1  - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1  - not using input device '/dev/input/event1'

This will then cause the APP weston-touch-calibrator can't list touch devices.

root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.

And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx7d-sdb.dts | 7 +------
 1 file changed, 1 insertion(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index e5f1bdbe7992..4e1a6cde90fe 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -206,12 +206,7 @@ tsc2046@0 {
 		interrupt-parent = <&gpio2>;
 		interrupts = <29 0>;
 		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
-		ti,x-min = /bits/ 16 <0>;
-		ti,x-max = /bits/ 16 <0>;
-		ti,y-min = /bits/ 16 <0>;
-		ti,y-max = /bits/ 16 <0>;
-		ti,pressure-max = /bits/ 16 <0>;
-		ti,x-plate-ohms = /bits/ 16 <400>;
+		touchscreen-max-pressure = <255>;
 		wakeup-source;
 	};
 };
-- 
2.35.1

[PATCH AUTOSEL 5.15 04/26] arm64: dts: qcom: sc7280-idp: correct ADC channel node name and unit address

[Sasha Levin]

From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

[ Upstream commit 5589ffb2da2a66988ab3a68334dad3e68b42e3a9 ]

Correct SPMI PMIC VADC channel node name:
1. Use hyphens instead of underscores,
2. Add missing unit address.

This fixes `make dtbs_check` warnings like:

  qcom/sc7280-idp.dtb: pmic@0: adc@3100: 'pmk8350_die_temp', 'pmr735a_die_temp' do not match any of the regexes: '^.*@[0-9a-f]+$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220828084341.112146-12-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dts  | 2 +-
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 64fc22aff33d..0b4bcc34b794 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -62,7 +62,7 @@ &ipa {
 };
 
 &pmk8350_vadc {
-	pmr735a_die_temp {
+	pmr735a-die-temp@403 {
 		reg = <PMR735A_ADC7_DIE_TEMP>;
 		label = "pmr735a_die_temp";
 		qcom,pre-scaling = <1 1>;
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 371a2a9dcf7a..1948b8011d2b 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -200,7 +200,7 @@ &ipa {
 };
 
 &pmk8350_vadc {
-	pmk8350_die_temp {
+	pmk8350-die-temp@3 {
 		reg = <PMK8350_ADC7_DIE_TEMP>;
 		label = "pmk8350_die_temp";
 		qcom,pre-scaling = <1 1>;
-- 
2.35.1

[PATCH AUTOSEL 5.15 05/26] ARM: dts: imx6q: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit b11d083c5dcec7c42fe982c854706d404ddd3a5f ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6q.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index 9caba4529c71..a8069e0a8fe8 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -163,6 +163,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x40000>;
+			ranges = <0 0x00900000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 5.15 06/26] ARM: dts: imx6dl: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit f5848b95633d598bacf0500e0108dc5961af88c0 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6dl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index fdd81fdc3f35..cd3183c36488 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -84,6 +84,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 5.15 07/26] ARM: dts: imx6qp: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 088fe5237435ee2f7ed4450519b2ef58b94c832f ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property
sram@940000: '#size-cells' is a required property
sram@940000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qp.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qp.dtsi b/arch/arm/boot/dts/imx6qp.dtsi
index b310f13a53f2..4d23c92aa8a6 100644
--- a/arch/arm/boot/dts/imx6qp.dtsi
+++ b/arch/arm/boot/dts/imx6qp.dtsi
@@ -9,12 +9,18 @@ soc {
 		ocram2: sram@940000 {
 			compatible = "mmio-sram";
 			reg = <0x00940000 0x20000>;
+			ranges = <0 0x00940000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
 		ocram3: sram@960000 {
 			compatible = "mmio-sram";
 			reg = <0x00960000 0x20000>;
+			ranges = <0 0x00960000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 5.15 08/26] ARM: dts: imx6sl: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 60c9213a1d9941a8b33db570796c3f9be8984974 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi
index 997b96c1c47b..5b4dfc62030e 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/imx6sl.dtsi
@@ -117,6 +117,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 5.15 09/26] ARM: dts: imx6sll: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 7492a83ed9b7a151e2dd11d64b06da7a7f0fa7f9 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sll.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi
index 04f8d637a501..eecb2f68a1c3 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/imx6sll.dtsi
@@ -117,6 +117,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		intc: interrupt-controller@a01000 {
-- 
2.35.1

[PATCH AUTOSEL 5.15 10/26] ARM: dts: imx6sx: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 415432c008b2bce8138841356ba444631cabaa50 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sx.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
index 8516730778df..8bef5440278b 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/imx6sx.dtsi
@@ -164,12 +164,18 @@ soc {
 		ocram_s: sram@8f8000 {
 			compatible = "mmio-sram";
 			reg = <0x008f8000 0x4000>;
+			ranges = <0 0x008f8000 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM_S>;
 		};
 
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 5.15 14/26] arm64: dts: imx8mq-librem5: Add bq25895 as max17055's power supply

[Sasha Levin]

From: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>

[ Upstream commit 6effe295e1a87408033c29dbcea9d5a5c8b937d5 ]

This allows the userspace to notice that there's not enough
current provided to charge the battery, and also fixes issues
with 0% SOC values being considered invalid.

Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
index 460ef0d86540..c86cd20d4e70 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
@@ -967,6 +967,7 @@ bat: fuel-gauge@36 {
 		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gauge>;
+		power-supplies = <&bq25895>;
 		maxim,over-heat-temp = <700>;
 		maxim,over-volt = <4500>;
 		maxim,rsns-microohm = <5000>;
-- 
2.35.1

[PATCH AUTOSEL 5.15 24/26] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Sasha Levin]

From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>

[ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]

PXs3 reference board can change each USB port 0 and 1 to device mode
with jumpers. Prepare devicetree sources for USB port 0 and 1.

This specifies dr_mode, pinctrl, and some quirks and removes nodes for
unused phys and vbus-supply properties.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-8-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/uniphier-pinctrl.dtsi       | 10 +++++
 arch/arm64/boot/dts/socionext/Makefile        |  4 +-
 .../socionext/uniphier-pxs3-ref-gadget0.dts   | 41 +++++++++++++++++++
 .../socionext/uniphier-pxs3-ref-gadget1.dts   | 40 ++++++++++++++++++
 4 files changed, 94 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
 create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts

diff --git a/arch/arm/boot/dts/uniphier-pinctrl.dtsi b/arch/arm/boot/dts/uniphier-pinctrl.dtsi
index c0fd029b37e5..f909ec2e5333 100644
--- a/arch/arm/boot/dts/uniphier-pinctrl.dtsi
+++ b/arch/arm/boot/dts/uniphier-pinctrl.dtsi
@@ -196,11 +196,21 @@ pinctrl_usb0: usb0 {
 		function = "usb0";
 	};
 
+	pinctrl_usb0_device: usb0-device {
+		groups = "usb0_device";
+		function = "usb0";
+	};
+
 	pinctrl_usb1: usb1 {
 		groups = "usb1";
 		function = "usb1";
 	};
 
+	pinctrl_usb1_device: usb1-device {
+		groups = "usb1_device";
+		function = "usb1";
+	};
+
 	pinctrl_usb2: usb2 {
 		groups = "usb2";
 		function = "usb2";
diff --git a/arch/arm64/boot/dts/socionext/Makefile b/arch/arm64/boot/dts/socionext/Makefile
index dda3da33614b..33989a9643ac 100644
--- a/arch/arm64/boot/dts/socionext/Makefile
+++ b/arch/arm64/boot/dts/socionext/Makefile
@@ -5,4 +5,6 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \
 	uniphier-ld20-akebi96.dtb \
 	uniphier-ld20-global.dtb \
 	uniphier-ld20-ref.dtb \
-	uniphier-pxs3-ref.dtb
+	uniphier-pxs3-ref.dtb \
+	uniphier-pxs3-ref-gadget0.dtb \
+	uniphier-pxs3-ref-gadget1.dtb
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
new file mode 100644
index 000000000000..7069f51bc120
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #0)
+//
+// Copyright (C) 2021 Socionext Inc.
+//   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+/dts-v1/;
+#include "uniphier-pxs3-ref.dts"
+
+/ {
+	model = "UniPhier PXs3 Reference Board (USB-Device #0)";
+};
+
+/* I2C3 pinctrl is shared with USB*VBUSIN */
+&i2c3 {
+	status = "disabled";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	pinctrl-0 = <&pinctrl_usb0_device>;
+	snps,dis_enblslpm_quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb2_gadget_lpm_disable;
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb0_hsphy0>, <&usb0_ssphy0>;
+};
+
+&usb0_hsphy0 {
+	/delete-property/ vbus-supply;
+};
+
+&usb0_ssphy0 {
+	/delete-property/ vbus-supply;
+};
+
+/delete-node/ &usb0_hsphy1;
+/delete-node/ &usb0_ssphy1;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
new file mode 100644
index 000000000000..a3cfa8113ffb
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #1)
+//
+// Copyright (C) 2021 Socionext Inc.
+//   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+/dts-v1/;
+#include "uniphier-pxs3-ref.dts"
+
+/ {
+	model = "UniPhier PXs3 Reference Board (USB-Device #1)";
+};
+
+/* I2C3 pinctrl is shared with USB*VBUSIN */
+&i2c3 {
+	status = "disabled";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "peripheral";
+	pinctrl-0 = <&pinctrl_usb1_device>;
+	snps,dis_enblslpm_quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb2_gadget_lpm_disable;
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb1_hsphy0>, <&usb1_ssphy0>;
+};
+
+&usb1_hsphy0 {
+	/delete-property/ vbus-supply;
+};
+
+&usb1_ssphy0 {
+	/delete-property/ vbus-supply;
+};
+
+/delete-node/ &usb1_hsphy1;
-- 
2.35.1