Re: [PATCH v2 13/15] scsi: ufs: ufs-qcom: Factor out the logic finding the HS Gear

[Andrew Halaney <ahalaney@redhat.com>]

On Mon, Oct 31, 2022 at 11:32:15PM +0530, Manivannan Sadhasivam wrote:
> In the preparation of adding support for new gears, let's move the
> logic that finds the gear for each platform to a new function. This helps
> with code readability and also allows the logic to be used in other places
> of the driver in future.
> 
> While at it, let's make it clear that this driver only supports symmetric
> gear setting (hs_tx_gear == hs_rx_gear).
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

Reviewed-by: Andrew Halaney <ahalaney@redhat.com>

> ---
>  drivers/ufs/host/ufs-qcom.c | 36 +++++++++++++++++++++++-------------
>  1 file changed, 23 insertions(+), 13 deletions(-)
> 
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index 38e2ed749d75..c93d2d38b43e 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -278,6 +278,26 @@ static int ufs_qcom_host_reset(struct ufs_hba *hba)
>  	return 0;
>  }
>  
> +static u32 ufs_qcom_get_hs_gear(struct ufs_hba *hba, u32 hs_gear)
> +{
> +	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> +
> +	if (host->hw_ver.major == 0x1) {
> +		/*
> +		 * HS-G3 operations may not reliably work on legacy QCOM
> +		 * UFS host controller hardware even though capability
> +		 * exchange during link startup phase may end up
> +		 * negotiating maximum supported gear as G3.
> +		 * Hence downgrade the maximum supported gear to HS-G2.
> +		 */
> +		if (hs_gear > UFS_HS_G2)
> +			return UFS_HS_G2;
> +	}
> +
> +	/* Default is HS-G3 */
> +	return UFS_HS_G3;
> +}
> +
>  static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
>  {
>  	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> @@ -692,19 +712,9 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
>  		ufshcd_init_pwr_dev_param(&ufs_qcom_cap);
>  		ufs_qcom_cap.hs_rate = UFS_QCOM_LIMIT_HS_RATE;
>  
> -		if (host->hw_ver.major == 0x1) {
> -			/*
> -			 * HS-G3 operations may not reliably work on legacy QCOM
> -			 * UFS host controller hardware even though capability
> -			 * exchange during link startup phase may end up
> -			 * negotiating maximum supported gear as G3.
> -			 * Hence downgrade the maximum supported gear to HS-G2.
> -			 */
> -			if (ufs_qcom_cap.hs_tx_gear > UFS_HS_G2)
> -				ufs_qcom_cap.hs_tx_gear = UFS_HS_G2;
> -			if (ufs_qcom_cap.hs_rx_gear > UFS_HS_G2)
> -				ufs_qcom_cap.hs_rx_gear = UFS_HS_G2;
> -		}
> +		/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
> +		ufs_qcom_cap.hs_tx_gear = ufs_qcom_cap.hs_rx_gear = ufs_qcom_get_hs_gear(hba,
> +									ufs_qcom_cap.hs_tx_gear);
>  
>  		ret = ufshcd_get_pwr_dev_param(&ufs_qcom_cap,
>  					       dev_max_params,
> -- 
> 2.25.1
>