[PATCH 0/4] Collected pending TI dmtimer dts changes

[PATCH 0/4] Collected pending TI dmtimer dts changes

[Tony Lindgren]

Hi,

Here are the pending TI dmtimer dts changes posted earlier. The related
driver and binding changes are now in the mainline Linux. There has been
no changes to these patches, I just updated them against current Linux
next and added the tags from Georgi.

Regards,

Tony


Tony Lindgren (4):
  arm64: dts: ti: k3-am65: Configure pinctrl for timer IO pads
  arm64: dts: ti: k3-am65: Add general purpose timers for am65
  arm64: dts: ti: k3-am62: Add general purpose timers for am62
  arm64: dts: ti: k3-am625-sk: Use pwm-led instead of gpio-led

 arch/arm64/boot/dts/ti/k3-am62-main.dtsi |  97 ++++++++++++++
 arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi  |  45 +++++++
 arch/arm64/boot/dts/ti/k3-am625-sk.dts   |  17 ++-
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 162 +++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi  |  63 +++++++++
 5 files changed, 379 insertions(+), 5 deletions(-)

-- 
2.37.3

[PATCH 1/4] arm64: dts: ti: k3-am65: Configure pinctrl for timer IO pads

[Tony Lindgren]

Compared to the earlier TI SoCs, am65 has an additional level of dedicated
multiplexing registers for the timer IO pads.

There are timer IO pads in the MCU domain, and in the MAIN domain. These
pads can be muxed for the related timers.

There are timer IO control registers for input and output. The registers
for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control
the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and
CTRLMMR_MCU_TIMERIO*_CTRL the output.

The multiplexing is documented in TRM "5.1.2.3.1.4 Timer IO Muxing Control
Registers" and "5.1.3.3.1.5 Timer IO Muxing Control Registers", and the
CASCADE_EN bit is documented in TRM "12.8.3.1 Timers Overview".

For chaining timers, the timer IO control registers also have a CASCADE_EN
input bit in the CTRLMMR_TIMER*_CTRL in the registers. The CASCADE_EN bit
muxes the previous timer output, or possibly and external TIMER_IO pad
source, to the input clock of the selected timer instance for odd numered
timers. For the even numbered timers, the CASCADE_EN bit does not do
anything. The timer cascade input routing options are shown in TRM
"Figure 12-3632. Timers Overview". For handling beyond multiplexing, the
driver support for timer cascading should be likely be handled via the
clock framework.

Cc: Keerthy <j-keerthy@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 18 ++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi  | 18 ++++++++++++++++++
 2 files changed, 36 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -131,6 +131,24 @@ rng: rng@4e10000 {
 		};
 	};
 
+	/* TIMERIO pad input CTRLMMR_TIMER*_CTRL registers */
+	main_timerio_input: pinctrl@104200 {
+		compatible = "pinctrl-single";
+		reg = <0x0 0x104200 0x0 0x30>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0x0000001ff>;
+	};
+
+	/* TIMERIO pad output CTCTRLMMR_TIMERIO*_CTRL registers */
+	main_timerio_output: pinctrl@104280 {
+		compatible = "pinctrl-single";
+		reg = <0x0 0x104280 0x0 0x20>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0x0000000f>;
+	};
+
 	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		reg = <0x0 0x11c000 0x0 0x2e4>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -20,6 +20,24 @@ phy_gmii_sel: phy@4040 {
 		};
 	};
 
+	/* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */
+	mcu_timerio_input: pinctrl@40f04200 {
+		compatible = "pinctrl-single";
+		reg = <0x0 0x40f04200 0x0 0x10>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0x00000101>;
+	};
+
+	/* MCU_TIMERIO pad output CTRLMMR_MCU_TIMERIO*_CTRL registers */
+	mcu_timerio_output: pinctrl@40f04280 {
+		compatible = "pinctrl-single";
+		reg = <0x0 0x40f04280 0x0 0x8>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0x00000003>;
+	};
+
 	mcu_uart0: serial@40a00000 {
 		compatible = "ti,am654-uart";
 			reg = <0x00 0x40a00000 0x00 0x100>;
-- 
2.37.3

[PATCH 2/4] arm64: dts: ti: k3-am65: Add general purpose timers for am65

[Tony Lindgren]

There are 12 general purpose timers on am65 that can be used for things
like PWM using pwm-omap-dmtimer driver. There are also additional four
timers in the MCU domain that do not have interrupts routable for Linux.

We configure the timers with the 25 MHz input clock by default as the
32.768 kHz clock may not be wired on the device. We leave the MCU domain
timers clock mux unconfigured, and mark the MCU domain timers reserved.
The MCU domain timers are likely reserved by the software for the ESM
module.

Compared to am64, the timer clocks are different on am65. And the MCU
timers are at a different IO address. Then j72 adds more timers compared
to am65 with a total of 30 timers. And the j72 clocks are different.

To avoid duplication for dtsi files, eventually we may want to consider
adding timer specific shared dtsi files with the timer clocks mapped
using SoC specific files in include/dt-bindings/clock. But let's get
am65 timers usable first.

Cc: Keerthy <j-keerthy@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 144 +++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi  |  45 +++++++
 2 files changed, 189 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -272,6 +272,150 @@ main_spi4: spi@2140000 {
 		#size-cells = <0>;
 	};
 
+	main_timer0: timer@2400000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2400000 0x00 0x400>;
+		interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 23 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 23 0>;
+		assigned-clock-parents = <&k3_clks 23 1>;
+		power-domains = <&k3_pds 23 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer1: timer@2410000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2410000 0x00 0x400>;
+		interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 24 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 24 0>;
+		assigned-clock-parents = <&k3_clks 24 1>;
+		power-domains = <&k3_pds 24 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer2: timer@2420000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2420000 0x00 0x400>;
+		interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 27 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 27 0>;
+		assigned-clock-parents = <&k3_clks 27 1>;
+		power-domains = <&k3_pds 27 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer3: timer@2430000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2430000 0x00 0x400>;
+		interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 28 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 28 0>;
+		assigned-clock-parents = <&k3_clks 28 1>;
+		power-domains = <&k3_pds 28 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer4: timer@2440000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2440000 0x00 0x400>;
+		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 29 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 29 0>;
+		assigned-clock-parents = <&k3_clks 29 1>;
+		power-domains = <&k3_pds 29 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer5: timer@2450000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2450000 0x00 0x400>;
+		interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 30 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 30 0>;
+		assigned-clock-parents = <&k3_clks 30 1>;
+		power-domains = <&k3_pds 30 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer6: timer@2460000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2460000 0x00 0x400>;
+		interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 31 0>;
+		assigned-clocks = <&k3_clks 31 0>;
+		assigned-clock-parents = <&k3_clks 31 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 31 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer7: timer@2470000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2470000 0x00 0x400>;
+		interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 32 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 32 0>;
+		assigned-clock-parents = <&k3_clks 32 1>;
+		power-domains = <&k3_pds 32 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer8: timer@2480000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2480000 0x00 0x400>;
+		interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 33 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 33 0>;
+		assigned-clock-parents = <&k3_clks 33 1>;
+		power-domains = <&k3_pds 33 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer9: timer@2490000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2490000 0x00 0x400>;
+		interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 34 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 34 0>;
+		assigned-clock-parents = <&k3_clks 34 1>;
+		power-domains = <&k3_pds 34 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer10: timer@24a0000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x24a0000 0x00 0x400>;
+		interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 25 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 25 0>;
+		assigned-clock-parents = <&k3_clks 25 1>;
+		power-domains = <&k3_pds 25 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer11: timer@24b0000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x24b0000 0x00 0x400>;
+		interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 26 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 26 0>;
+		assigned-clock-parents = <&k3_clks 26 1>;
+		power-domains = <&k3_pds 26 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
 	sdhci0: mmc@4f80000 {
 		compatible = "ti,am654-sdhci-5.1";
 		reg = <0x0 0x4f80000 0x0 0x260>, <0x0 0x4f90000 0x0 0x134>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -132,6 +132,51 @@ adc {
 		};
 	};
 
+	/*
+	 * The MCU domain timer interrupts are routed only to the ESM module,
+	 * and not currently available for Linux. The MCU domain timers are
+	 * of limited use without interrupts, and likely reserved by the ESM.
+	 */
+	mcu_timer0: timer@40400000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x40400000 0x00 0x400>;
+		clocks = <&k3_clks 35 0>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer1: timer@40410000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x40410000 0x00 0x400>;
+		clocks = <&k3_clks 36 0>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer2: timer@40420000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x40420000 0x00 0x400>;
+		clocks = <&k3_clks 37 0>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer3: timer@40430000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x40430000 0x00 0x400>;
+		clocks = <&k3_clks 38 0>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
 	mcu_navss: bus@28380000 {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
-- 
2.37.3

[PATCH 3/4] arm64: dts: ti: k3-am62: Add general purpose timers for am62

[Tony Lindgren]

There are 8 general purpose timers on am65 that can be used for things
like PWM using pwm-omap-dmtimer driver. There are also additional four
timers in the MCU domain that do not have interrupts routable for Linux.

We configure the timers with the 25 MHz input clock by default as the
32.768 kHz clock may not be wired on the device. We leave the MCU domain
timers clock mux unconfigured, and mark the MCU domain timers reserved.
The MCU domain timers are likely reserved by the software for the ESM
module.

Compared to am65, the timers on am62 do not have a dedicated IO mux for
the timers. On am62, the timers have different interrupts, clocks and
power domains compared to am65, and the MCU timers are at a different
IO address.

Cc: Keerthy <j-keerthy@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 97 ++++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi  | 45 +++++++++++
 2 files changed, 142 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -192,6 +192,103 @@ main_pmx0: pinctrl@f4000 {
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
 
+	main_timer0: timer@2400000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2400000 0x00 0x400>;
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 36 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 36 2>;
+		assigned-clock-parents = <&k3_clks 36 3>;
+		power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer1: timer@2410000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2410000 0x00 0x400>;
+		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 37 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 37 2>;
+		assigned-clock-parents = <&k3_clks 37 3>;
+		power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer2: timer@2420000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2420000 0x00 0x400>;
+		interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 38 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 38 2>;
+		assigned-clock-parents = <&k3_clks 38 3>;
+		power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer3: timer@2430000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2430000 0x00 0x400>;
+		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 39 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 39 2>;
+		assigned-clock-parents = <&k3_clks 39 3>;
+		power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer4: timer@2440000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2440000 0x00 0x400>;
+		interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 40 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 40 2>;
+		assigned-clock-parents = <&k3_clks 40 3>;
+		power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer5: timer@2450000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2450000 0x00 0x400>;
+		interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 41 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 41 2>;
+		assigned-clock-parents = <&k3_clks 41 3>;
+		power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer6: timer@2460000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2460000 0x00 0x400>;
+		interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 42 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 42 2>;
+		assigned-clock-parents = <&k3_clks 42 3>;
+		power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer7: timer@2470000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2470000 0x00 0x400>;
+		interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 43 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 43 2>;
+		assigned-clock-parents = <&k3_clks 43 3>;
+		power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+
 	main_uart0: serial@2800000 {
 		compatible = "ti,am64-uart", "ti,am654-uart";
 		reg = <0x00 0x02800000 0x00 0x100>;
diff --git a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
--- a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
@@ -14,6 +14,51 @@ mcu_pmx0: pinctrl@4084000 {
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
 
+	/*
+	 * The MCU domain timer interrupts are routed only to the ESM module,
+	 * and not currently available for Linux. The MCU domain timers are
+	 * of limited use without interrupts, and likely reserved by the ESM.
+	 */
+	mcu_timer0: timer@4800000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4800000 0x00 0x400>;
+		clocks = <&k3_clks 35 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer1: timer@4810000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4810000 0x00 0x400>;
+		clocks = <&k3_clks 48 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer2: timer@4820000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4820000 0x00 0x400>;
+		clocks = <&k3_clks 49 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer3: timer@4830000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4830000 0x00 0x400>;
+		clocks = <&k3_clks 50 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
 	mcu_uart0: serial@4a00000 {
 		compatible = "ti,am64-uart", "ti,am654-uart";
 		reg = <0x00 0x04a00000 0x00 0x100>;
-- 
2.37.3

[PATCH 4/4] arm64: dts: ti: k3-am625-sk: Use pwm-led instead of gpio-led

[Tony Lindgren]

On am625, pad c17 can be used either in gpio mode or pwm mode to control
the connected led. Let's change to use pwm-led for additional brighness
control.

The pwm controller is dmtimer7 for pad C17. We configure it for 128 Hz
rate (1000000000 / 7812500) similar to what has been done elsewhere for
pwm-leds.

Cc: Keerthy <j-keerthy@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm64/boot/dts/ti/k3-am625-sk.dts | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -131,18 +131,25 @@ vdd_sd_dv: regulator-4 {
 	};
 
 	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&usr_led_pins_default>;
+		compatible = "pwm-leds";
 
 		led-0 {
 			label = "am62-sk:green:heartbeat";
-			gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
+			pwms = <&main_pwm7 0 7812500 0>;
+			max-brightness = <255>;
 			linux,default-trigger = "heartbeat";
 			function = LED_FUNCTION_HEARTBEAT;
 			default-state = "off";
 		};
 	};
+
+	main_pwm7: dmtimer-main-pwm-7 {
+		pinctrl-0 = <&usr_led_pins_default>;
+		pinctrl-names = "default";
+		compatible = "ti,omap-dmtimer-pwm";
+		#pwm-cells = <3>;
+		ti,timers = <&main_timer7>;
+	};
 };
 
 &main_pmx0 {
@@ -203,7 +210,7 @@ AM62X_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */
 
 	usr_led_pins_default: usr-led-pins-default {
 		pinctrl-single,pins = <
-			AM62X_IOPAD(0x244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
+			AM62X_IOPAD(0x244, PIN_OUTPUT, 2) /* (C17) MMC1_SDWP.TIMER_IO7 */
 		>;
 	};
 
-- 
2.37.3