[PATCH v1 0/5] arm64: dts: qcom: sm8450-hdk: enable HDMI output

[PATCH v1 0/5] arm64: dts: qcom: sm8450-hdk: enable HDMI output

[Dmitry Baryshkov]

Add device tree nodes for MDSS, DPU and DSI devices on Qualcomm SM8450
platform. Enable these devices and add the HDMI bridge configuration on
SM8450 HDK.

Dmitry Baryshkov (3):
  arm64: dts: qcom: sm8450: add RPMH_REGULATOR_LEVEL_LOW_SVS_D1
  arm64: dts: qcom: sm8450: add display hardware devices
  arm64: dts: qcom: sm8450-hdk: enable display hardware

Vinod Koul (2):
  arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge
  arm64: dts: qcom: sm8450-hdk: Enable HDMI Display

 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 124 ++++++++++
 arch/arm64/boot/dts/qcom/sm8450.dtsi    | 304 +++++++++++++++++++++++-
 include/dt-bindings/power/qcom-rpmpd.h  |   1 +
 3 files changed, 417 insertions(+), 12 deletions(-)

-- 
2.35.1

[PATCH v1 1/5] arm64: dts: qcom: sm8450: add RPMH_REGULATOR_LEVEL_LOW_SVS_D1

[Dmitry Baryshkov]

Add another power saving state used on SM8450. Unfortunately adding it
in proper place causes renumbering of all the opp states in sm8450.dtsi

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi   | 20 ++++++++++++--------
 include/dt-bindings/power/qcom-rpmpd.h |  1 +
 2 files changed, 13 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index eeff62d0954b..250e6b883ca3 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -3197,35 +3197,39 @@ rpmhpd_opp_min_svs: opp2 {
 						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
 					};
 
-					rpmhpd_opp_low_svs: opp3 {
+					rpmhpd_opp_low_svs_d1: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
+					};
+
+					rpmhpd_opp_low_svs: opp4 {
 						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
 					};
 
-					rpmhpd_opp_svs: opp4 {
+					rpmhpd_opp_svs: opp5 {
 						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
 					};
 
-					rpmhpd_opp_svs_l1: opp5 {
+					rpmhpd_opp_svs_l1: opp6 {
 						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
 					};
 
-					rpmhpd_opp_nom: opp6 {
+					rpmhpd_opp_nom: opp7 {
 						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
 					};
 
-					rpmhpd_opp_nom_l1: opp7 {
+					rpmhpd_opp_nom_l1: opp8 {
 						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
 					};
 
-					rpmhpd_opp_nom_l2: opp8 {
+					rpmhpd_opp_nom_l2: opp9 {
 						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
 					};
 
-					rpmhpd_opp_turbo: opp9 {
+					rpmhpd_opp_turbo: opp10 {
 						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
 					};
 
-					rpmhpd_opp_turbo_l1: opp10 {
+					rpmhpd_opp_turbo_l1: opp11 {
 						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
 					};
 				};
diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
index 578e060890dd..69aef395d85b 100644
--- a/include/dt-bindings/power/qcom-rpmpd.h
+++ b/include/dt-bindings/power/qcom-rpmpd.h
@@ -168,6 +168,7 @@
 /* SDM845 Power Domain performance levels */
 #define RPMH_REGULATOR_LEVEL_RETENTION	16
 #define RPMH_REGULATOR_LEVEL_MIN_SVS	48
+#define RPMH_REGULATOR_LEVEL_LOW_SVS_D1	56
 #define RPMH_REGULATOR_LEVEL_LOW_SVS	64
 #define RPMH_REGULATOR_LEVEL_SVS	128
 #define RPMH_REGULATOR_LEVEL_SVS_L0	144
-- 
2.35.1

Re: [PATCH v1 1/5] arm64: dts: qcom: sm8450: add RPMH_REGULATOR_LEVEL_LOW_SVS_D1

[Konrad Dybcio]

On 04/11/2022 14:13, Dmitry Baryshkov wrote:
> Add another power saving state used on SM8450. Unfortunately adding it
> in proper place causes renumbering of all the opp states in sm8450.dtsi
>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>


Konrad

>   arch/arm64/boot/dts/qcom/sm8450.dtsi   | 20 ++++++++++++--------
>   include/dt-bindings/power/qcom-rpmpd.h |  1 +
>   2 files changed, 13 insertions(+), 8 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index eeff62d0954b..250e6b883ca3 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -3197,35 +3197,39 @@ rpmhpd_opp_min_svs: opp2 {
>   						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
>   					};
>   
> -					rpmhpd_opp_low_svs: opp3 {
> +					rpmhpd_opp_low_svs_d1: opp3 {
> +						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
> +					};
> +
> +					rpmhpd_opp_low_svs: opp4 {
>   						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
>   					};
>   
> -					rpmhpd_opp_svs: opp4 {
> +					rpmhpd_opp_svs: opp5 {
>   						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
>   					};
>   
> -					rpmhpd_opp_svs_l1: opp5 {
> +					rpmhpd_opp_svs_l1: opp6 {
>   						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
>   					};
>   
> -					rpmhpd_opp_nom: opp6 {
> +					rpmhpd_opp_nom: opp7 {
>   						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
>   					};
>   
> -					rpmhpd_opp_nom_l1: opp7 {
> +					rpmhpd_opp_nom_l1: opp8 {
>   						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
>   					};
>   
> -					rpmhpd_opp_nom_l2: opp8 {
> +					rpmhpd_opp_nom_l2: opp9 {
>   						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
>   					};
>   
> -					rpmhpd_opp_turbo: opp9 {
> +					rpmhpd_opp_turbo: opp10 {
>   						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
>   					};
>   
> -					rpmhpd_opp_turbo_l1: opp10 {
> +					rpmhpd_opp_turbo_l1: opp11 {
>   						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
>   					};
>   				};
> diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
> index 578e060890dd..69aef395d85b 100644
> --- a/include/dt-bindings/power/qcom-rpmpd.h
> +++ b/include/dt-bindings/power/qcom-rpmpd.h
> @@ -168,6 +168,7 @@
>   /* SDM845 Power Domain performance levels */
>   #define RPMH_REGULATOR_LEVEL_RETENTION	16
>   #define RPMH_REGULATOR_LEVEL_MIN_SVS	48
> +#define RPMH_REGULATOR_LEVEL_LOW_SVS_D1	56
>   #define RPMH_REGULATOR_LEVEL_LOW_SVS	64
>   #define RPMH_REGULATOR_LEVEL_SVS	128
>   #define RPMH_REGULATOR_LEVEL_SVS_L0	144

[PATCH v1 2/5] arm64: dts: qcom: sm8450: add display hardware devices

[Dmitry Baryshkov]

Add devices tree nodes describing display hardware on SM8450:
- Display Clock Controller
- MDSS
- MDP
- two DSI controllers and DSI PHYs

This does not provide support for DP controllers present on SM8450.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 284 ++++++++++++++++++++++++++-
 1 file changed, 280 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 250e6b883ca3..23f989dedfdb 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -2401,6 +2401,282 @@ camcc: clock-controller@ade0000 {
 			status = "disabled";
 		};
 
+		mdss: mdss@ae00000 {
+			compatible = "qcom,sm8450-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			/* same path used twice */
+			interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>,
+					<&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>;
+			interconnect-names = "mdp0-mem", "mdp1-mem";
+
+			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+			power-domains = <&dispcc MDSS_GDSC>;
+
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&gcc GCC_DISP_SF_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+			clock-names = "iface", "bus", "nrt_bus", "core";
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			iommus = <&apps_smmu 0x2800 0x402>;
+
+			status = "disabled";
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			mdss_mdp: mdp@ae01000 {
+				compatible = "qcom,sm8450-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp", "vbif";
+
+				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+					<&gcc GCC_DISP_SF_AXI_CLK>,
+					<&dispcc DISP_CC_MDSS_AHB_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_CLK>,
+					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "bus",
+					      "nrt_bus",
+					      "iface",
+					      "lut",
+					      "core",
+					      "vsync";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <19200000>;
+
+				operating-points-v2 = <&mdp_opp_table>;
+				power-domains = <&rpmhpd SM8450_MMCX>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dpu_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dpu_intf2_out: endpoint {
+							remote-endpoint = <&dsi1_in>;
+						};
+					};
+
+				};
+
+				mdp_opp_table: mdp-opp-table {
+					compatible = "operating-points-v2";
+
+					opp-172000000 {
+						opp-hz = /bits/ 64 <172000000>;
+						required-opps = <&rpmhpd_opp_low_svs_d1>;
+					};
+
+					opp-200000000 {
+						opp-hz = /bits/ 64 <200000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-325000000 {
+						opp-hz = /bits/ 64 <325000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-375000000 {
+						opp-hz = /bits/ 64 <375000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-500000000 {
+						opp-hz = /bits/ 64 <500000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			dsi0: dsi@ae94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae94000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					<&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>;
+
+				operating-points-v2 = <&dsi_opp_table>;
+				power-domains = <&rpmhpd SM8450_MMCX>;
+
+				phys = <&dsi0_phy>;
+				phy-names = "dsi";
+
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&dpu_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi0_phy: dsi-phy@ae94400 {
+				compatible = "qcom,dsi-phy-7nm";
+				reg = <0 0x0ae94400 0 0x200>,
+				      <0 0x0ae94600 0 0x280>,
+				      <0 0x0ae94900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+
+			dsi1: dsi@ae96000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae96000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <5>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+				assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>;
+
+				operating-points-v2 = <&dsi_opp_table>;
+				power-domains = <&rpmhpd SM8450_MMCX>;
+
+				phys = <&dsi1_phy>;
+				phy-names = "dsi";
+
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi1_in: endpoint {
+							remote-endpoint = <&dpu_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi1_phy: dsi-phy@ae96400 {
+				compatible = "qcom,dsi-phy-7nm";
+				reg = <0 0x0ae96400 0 0x200>,
+				      <0 0x0ae96600 0 0x280>,
+				      <0 0x0ae96900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+
+				dsi_opp_table: dsi-opp-table {
+					compatible = "operating-points-v2";
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
+			};
+		};
+
 		dispcc: clock-controller@af00000 {
 			compatible = "qcom,sm8450-dispcc";
 			reg = <0 0x0af00000 0 0x20000>;
@@ -2408,10 +2684,10 @@ dispcc: clock-controller@af00000 {
 				 <&rpmhcc RPMH_CXO_CLK_A>,
 				 <&gcc GCC_DISP_AHB_CLK>,
 				 <&sleep_clk>,
-				 <0>, /* dsi0 */
-				 <0>,
-				 <0>, /* dsi1 */
-				 <0>,
+				 <&dsi0_phy 0>, /* dsi0 */
+				 <&dsi0_phy 1>,
+				 <&dsi1_phy 0>, /* dsi1 */
+				 <&dsi1_phy 1>,
 				 <0>, /* dp0 */
 				 <0>,
 				 <0>, /* dp1 */
-- 
2.35.1

Re: [PATCH v1 2/5] arm64: dts: qcom: sm8450: add display hardware devices

[Konrad Dybcio]

On 04/11/2022 14:13, Dmitry Baryshkov wrote:
> Add devices tree nodes describing display hardware on SM8450:
> - Display Clock Controller
> - MDSS
> - MDP
> - two DSI controllers and DSI PHYs
>
> This does not provide support for DP controllers present on SM8450.
>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sm8450.dtsi | 284 ++++++++++++++++++++++++++-
>   1 file changed, 280 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index 250e6b883ca3..23f989dedfdb 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -2401,6 +2401,282 @@ camcc: clock-controller@ade0000 {
>   			status = "disabled";
>   		};
>   
> +		mdss: mdss@ae00000 {
> +			compatible = "qcom,sm8450-mdss";
> +			reg = <0 0x0ae00000 0 0x1000>;
> +			reg-names = "mdss";
> +
> +			/* same path used twice */
> +			interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>,
> +					<&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>;
> +			interconnect-names = "mdp0-mem", "mdp1-mem";
> +
> +			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
> +
> +			power-domains = <&dispcc MDSS_GDSC>;
> +
> +			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +				 <&gcc GCC_DISP_HF_AXI_CLK>,
> +				 <&gcc GCC_DISP_SF_AXI_CLK>,
> +				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
> +			clock-names = "iface", "bus", "nrt_bus", "core";
> +
> +			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +
> +			iommus = <&apps_smmu 0x2800 0x402>;
> +
> +			status = "disabled";
> +
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +
> +			mdss_mdp: mdp@ae01000 {
> +				compatible = "qcom,sm8450-dpu";
> +				reg = <0 0x0ae01000 0 0x8f000>,
> +				      <0 0x0aeb0000 0 0x2008>;
> +				reg-names = "mdp", "vbif";
> +
> +				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> +					<&gcc GCC_DISP_SF_AXI_CLK>,
> +					<&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> +					<&dispcc DISP_CC_MDSS_MDP_CLK>,
> +					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				clock-names = "bus",
> +					      "nrt_bus",
> +					      "iface",
> +					      "lut",
> +					      "core",
> +					      "vsync";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				assigned-clock-rates = <19200000>;
> +
> +				operating-points-v2 = <&mdp_opp_table>;
> +				power-domains = <&rpmhpd SM8450_MMCX>;
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dpu_intf1_out: endpoint {
> +							remote-endpoint = <&dsi0_in>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dpu_intf2_out: endpoint {
> +							remote-endpoint = <&dsi1_in>;
> +						};
> +					};
> +
> +				};
> +
> +				mdp_opp_table: mdp-opp-table {
> +					compatible = "operating-points-v2";
> +
> +					opp-172000000 {
> +						opp-hz = /bits/ 64 <172000000>;
> +						required-opps = <&rpmhpd_opp_low_svs_d1>;
> +					};
> +
> +					opp-200000000 {
> +						opp-hz = /bits/ 64 <200000000>;
> +						required-opps = <&rpmhpd_opp_low_svs>;
> +					};
> +
> +					opp-325000000 {
> +						opp-hz = /bits/ 64 <325000000>;
> +						required-opps = <&rpmhpd_opp_svs>;
> +					};
> +
> +					opp-375000000 {
> +						opp-hz = /bits/ 64 <375000000>;
> +						required-opps = <&rpmhpd_opp_svs_l1>;
> +					};
> +
> +					opp-500000000 {
> +						opp-hz = /bits/ 64 <500000000>;
> +						required-opps = <&rpmhpd_opp_nom>;
> +					};
> +				};
> +			};
> +
> +			dsi0: dsi@ae94000 {
> +				compatible = "qcom,mdss-dsi-ctrl";
> +				reg = <0 0x0ae94000 0 0x400>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <4>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> +					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					<&gcc GCC_DISP_HF_AXI_CLK>;
> +				clock-names = "byte",
> +					      "byte_intf",
> +					      "pixel",
> +					      "core",
> +					      "iface",
> +					      "bus";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
> +				assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>;
> +
> +				operating-points-v2 = <&dsi_opp_table>;
> +				power-domains = <&rpmhpd SM8450_MMCX>;
> +
> +				phys = <&dsi0_phy>;
> +				phy-names = "dsi";
> +
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dsi0_in: endpoint {
> +							remote-endpoint = <&dpu_intf1_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dsi0_out: endpoint {
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi0_phy: dsi-phy@ae94400 {
> +				compatible = "qcom,dsi-phy-7nm";
> +				reg = <0 0x0ae94400 0 0x200>,
> +				      <0 0x0ae94600 0 0x280>,
> +				      <0 0x0ae94900 0 0x260>;
> +				reg-names = "dsi_phy",
> +					    "dsi_phy_lane",
> +					    "dsi_pll";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&rpmhcc RPMH_CXO_CLK>;
> +				clock-names = "iface", "ref";
> +
> +				status = "disabled";
> +			};
> +
> +			dsi1: dsi@ae96000 {
> +				compatible = "qcom,mdss-dsi-ctrl";
> +				reg = <0 0x0ae96000 0 0x400>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <5>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
> +					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_DISP_HF_AXI_CLK>;
> +				clock-names = "byte",
> +					      "byte_intf",
> +					      "pixel",
> +					      "core",
> +					      "iface",
> +					      "bus";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
> +				assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>;
> +
> +				operating-points-v2 = <&dsi_opp_table>;
> +				power-domains = <&rpmhpd SM8450_MMCX>;
> +
> +				phys = <&dsi1_phy>;
> +				phy-names = "dsi";
> +
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dsi1_in: endpoint {
> +							remote-endpoint = <&dpu_intf2_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dsi1_out: endpoint {
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi1_phy: dsi-phy@ae96400 {
> +				compatible = "qcom,dsi-phy-7nm";
> +				reg = <0 0x0ae96400 0 0x200>,
> +				      <0 0x0ae96600 0 0x280>,
> +				      <0 0x0ae96900 0 0x260>;
> +				reg-names = "dsi_phy",
> +					    "dsi_phy_lane",
> +					    "dsi_pll";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&rpmhcc RPMH_CXO_CLK>;
> +				clock-names = "iface", "ref";
> +
> +				status = "disabled";
> +
> +				dsi_opp_table: dsi-opp-table {
> +					compatible = "operating-points-v2";
> +
> +					opp-187500000 {
> +						opp-hz = /bits/ 64 <187500000>;
> +						required-opps = <&rpmhpd_opp_low_svs>;
> +					};
> +
> +					opp-300000000 {
> +						opp-hz = /bits/ 64 <300000000>;
> +						required-opps = <&rpmhpd_opp_svs>;
> +					};
> +
> +					opp-358000000 {
> +						opp-hz = /bits/ 64 <358000000>;
> +						required-opps = <&rpmhpd_opp_svs_l1>;
> +					};
> +				};
> +			};
> +		};
> +
>   		dispcc: clock-controller@af00000 {
>   			compatible = "qcom,sm8450-dispcc";
>   			reg = <0 0x0af00000 0 0x20000>;
> @@ -2408,10 +2684,10 @@ dispcc: clock-controller@af00000 {
>   				 <&rpmhcc RPMH_CXO_CLK_A>,
>   				 <&gcc GCC_DISP_AHB_CLK>,
>   				 <&sleep_clk>,
> -				 <0>, /* dsi0 */
> -				 <0>,
> -				 <0>, /* dsi1 */
> -				 <0>,
> +				 <&dsi0_phy 0>, /* dsi0 */
> +				 <&dsi0_phy 1>,
> +				 <&dsi1_phy 0>, /* dsi1 */
> +				 <&dsi1_phy 1>,

I think these comments are superfluous now.


Aside from that:


Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>

Konrad

>   				 <0>, /* dp0 */
>   				 <0>,
>   				 <0>, /* dp1 */

Re: [PATCH v1 2/5] arm64: dts: qcom: sm8450: add display hardware devices

[Krzysztof Kozlowski]

On 04/11/2022 09:13, Dmitry Baryshkov wrote:
> Add devices tree nodes describing display hardware on SM8450:
> - Display Clock Controller
> - MDSS
> - MDP
> - two DSI controllers and DSI PHYs
> 
> This does not provide support for DP controllers present on SM8450.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8450.dtsi | 284 ++++++++++++++++++++++++++-
>  1 file changed, 280 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index 250e6b883ca3..23f989dedfdb 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -2401,6 +2401,282 @@ camcc: clock-controller@ade0000 {
>  			status = "disabled";
>  		};
>  
> +		mdss: mdss@ae00000 {
> +			compatible = "qcom,sm8450-mdss";
> +			reg = <0 0x0ae00000 0 0x1000>;
> +			reg-names = "mdss";
> +
> +			/* same path used twice */
> +			interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>,
> +					<&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>;
> +			interconnect-names = "mdp0-mem", "mdp1-mem";
> +
> +			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
> +
> +			power-domains = <&dispcc MDSS_GDSC>;
> +
> +			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +				 <&gcc GCC_DISP_HF_AXI_CLK>,
> +				 <&gcc GCC_DISP_SF_AXI_CLK>,
> +				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
> +			clock-names = "iface", "bus", "nrt_bus", "core";
> +
> +			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +
> +			iommus = <&apps_smmu 0x2800 0x402>;
> +
> +			status = "disabled";

Status as last property.

> +
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +
> +			mdss_mdp: mdp@ae01000 {


Isn't this "display-controller" in the bindings and other cases?

> +				compatible = "qcom,sm8450-dpu";
> +				reg = <0 0x0ae01000 0 0x8f000>,
> +				      <0 0x0aeb0000 0 0x2008>;
> +				reg-names = "mdp", "vbif";
> +
> +				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> +					<&gcc GCC_DISP_SF_AXI_CLK>,
> +					<&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> +					<&dispcc DISP_CC_MDSS_MDP_CLK>,
> +					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				clock-names = "bus",
> +					      "nrt_bus",
> +					      "iface",
> +					      "lut",
> +					      "core",
> +					      "vsync";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				assigned-clock-rates = <19200000>;
> +
> +				operating-points-v2 = <&mdp_opp_table>;
> +				power-domains = <&rpmhpd SM8450_MMCX>;
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dpu_intf1_out: endpoint {
> +							remote-endpoint = <&dsi0_in>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dpu_intf2_out: endpoint {
> +							remote-endpoint = <&dsi1_in>;
> +						};
> +					};
> +
> +				};
> +
> +				mdp_opp_table: mdp-opp-table {
> +					compatible = "operating-points-v2";
> +
> +					opp-172000000 {
> +						opp-hz = /bits/ 64 <172000000>;
> +						required-opps = <&rpmhpd_opp_low_svs_d1>;
> +					};
> +
> +					opp-200000000 {
> +						opp-hz = /bits/ 64 <200000000>;
> +						required-opps = <&rpmhpd_opp_low_svs>;
> +					};
> +
> +					opp-325000000 {
> +						opp-hz = /bits/ 64 <325000000>;
> +						required-opps = <&rpmhpd_opp_svs>;
> +					};
> +
> +					opp-375000000 {
> +						opp-hz = /bits/ 64 <375000000>;
> +						required-opps = <&rpmhpd_opp_svs_l1>;
> +					};
> +
> +					opp-500000000 {
> +						opp-hz = /bits/ 64 <500000000>;
> +						required-opps = <&rpmhpd_opp_nom>;
> +					};
> +				};
> +			};
> +
> +			dsi0: dsi@ae94000 {
> +				compatible = "qcom,mdss-dsi-ctrl";
> +				reg = <0 0x0ae94000 0 0x400>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <4>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> +					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					<&gcc GCC_DISP_HF_AXI_CLK>;
> +				clock-names = "byte",
> +					      "byte_intf",
> +					      "pixel",
> +					      "core",
> +					      "iface",
> +					      "bus";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
> +				assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>;
> +
> +				operating-points-v2 = <&dsi_opp_table>;
> +				power-domains = <&rpmhpd SM8450_MMCX>;
> +
> +				phys = <&dsi0_phy>;
> +				phy-names = "dsi";
> +
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dsi0_in: endpoint {
> +							remote-endpoint = <&dpu_intf1_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dsi0_out: endpoint {
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi0_phy: dsi-phy@ae94400 {

You were just renaming all these to "phy" recently.

> +				compatible = "qcom,dsi-phy-7nm";
> +				reg = <0 0x0ae94400 0 0x200>,
> +				      <0 0x0ae94600 0 0x280>,
> +				      <0 0x0ae94900 0 0x260>;
> +				reg-names = "dsi_phy",
> +					    "dsi_phy_lane",
> +					    "dsi_pll";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&rpmhcc RPMH_CXO_CLK>;
> +				clock-names = "iface", "ref";
> +
> +				status = "disabled";
> +			};
> +
> +			dsi1: dsi@ae96000 {
> +				compatible = "qcom,mdss-dsi-ctrl";
> +				reg = <0 0x0ae96000 0 0x400>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <5>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
> +					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_DISP_HF_AXI_CLK>;
> +				clock-names = "byte",
> +					      "byte_intf",
> +					      "pixel",
> +					      "core",
> +					      "iface",
> +					      "bus";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
> +				assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>;
> +
> +				operating-points-v2 = <&dsi_opp_table>;
> +				power-domains = <&rpmhpd SM8450_MMCX>;
> +
> +				phys = <&dsi1_phy>;
> +				phy-names = "dsi";
> +
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dsi1_in: endpoint {
> +							remote-endpoint = <&dpu_intf2_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dsi1_out: endpoint {
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi1_phy: dsi-phy@ae96400 {

Same here


Best regards,
Krzysztof

[PATCH v1 3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware

[Dmitry Baryshkov]

Enable MDSS/DPU/DSI0 on SM8450-HDK device. Note, there is no panel
configuration (yet).

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index 38ccd44620d0..e1a4cf1ee51d 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -442,3 +442,21 @@ &usb_1_qmpphy {
 	vdda-phy-supply = <&vreg_l6b_1p2>;
 	vdda-pll-supply = <&vreg_l1b_0p91>;
 };
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l6b_1p2>;
+};
+
+&dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vreg_l5b_0p88>;
+};
-- 
2.35.1

Re: [PATCH v1 3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware

[Konrad Dybcio]

On 04/11/2022 14:13, Dmitry Baryshkov wrote:
> Enable MDSS/DPU/DSI0 on SM8450-HDK device. Note, there is no panel
> configuration (yet).
>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 18 ++++++++++++++++++
>   1 file changed, 18 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> index 38ccd44620d0..e1a4cf1ee51d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> @@ -442,3 +442,21 @@ &usb_1_qmpphy {
>   	vdda-phy-supply = <&vreg_l6b_1p2>;
>   	vdda-pll-supply = <&vreg_l1b_0p91>;
>   };
> +
> +&mdss {
> +	status = "okay";
> +};
> +
> +&mdss_mdp {
> +	status = "okay";
> +};
> +
> +&dsi0 {
> +	status = "okay";
> +	vdda-supply = <&vreg_l6b_1p2>;
> +};
> +
> +&dsi0_phy {
> +	status = "okay";
> +	vdds-supply = <&vreg_l5b_0p88>;
> +};

Sort the nodes alphabetically and place status last, please.


Konrad

Re: [PATCH v1 3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware

[Vinod Koul]

On 04-11-22, 16:13, Dmitry Baryshkov wrote:
> Enable MDSS/DPU/DSI0 on SM8450-HDK device. Note, there is no panel
> configuration (yet).
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> index 38ccd44620d0..e1a4cf1ee51d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> @@ -442,3 +442,21 @@ &usb_1_qmpphy {
>  	vdda-phy-supply = <&vreg_l6b_1p2>;
>  	vdda-pll-supply = <&vreg_l1b_0p91>;
>  };
> +
> +&mdss {
> +	status = "okay";
> +};
> +
> +&mdss_mdp {
> +	status = "okay";
> +};
> +
> +&dsi0 {
> +	status = "okay";
> +	vdda-supply = <&vreg_l6b_1p2>;
> +};
> +
> +&dsi0_phy {
> +	status = "okay";
> +	vdds-supply = <&vreg_l5b_0p88>;
> +};

This is missing dispcc, please enable that node too.

Also, sort this please

> -- 
> 2.35.1

-- 
~Vinod

Re: [PATCH v1 3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware

[Bjorn Andersson]

On Fri, Nov 04, 2022 at 04:13:56PM +0300, Dmitry Baryshkov wrote:
> Enable MDSS/DPU/DSI0 on SM8450-HDK device. Note, there is no panel
> configuration (yet).
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> index 38ccd44620d0..e1a4cf1ee51d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> @@ -442,3 +442,21 @@ &usb_1_qmpphy {
>  	vdda-phy-supply = <&vreg_l6b_1p2>;
>  	vdda-pll-supply = <&vreg_l1b_0p91>;
>  };
> +
> +&mdss {
> +	status = "okay";
> +};
> +
> +&mdss_mdp {
> +	status = "okay";
> +};
> +
> +&dsi0 {

Please prefix the labels with "mdss_" so that you can keep them sorted
alphabetically.

THanks,
Bjorn

> +	status = "okay";
> +	vdda-supply = <&vreg_l6b_1p2>;
> +};
> +
> +&dsi0_phy {
> +	status = "okay";
> +	vdds-supply = <&vreg_l5b_0p88>;
> +};
> -- 
> 2.35.1
> 

Re: [PATCH v1 3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware

[Konrad Dybcio]

On 06/11/2022 05:30, Bjorn Andersson wrote:
> On Fri, Nov 04, 2022 at 04:13:56PM +0300, Dmitry Baryshkov wrote:
>> Enable MDSS/DPU/DSI0 on SM8450-HDK device. Note, there is no panel
>> configuration (yet).
>>
>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>> ---
>>   arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 18 ++++++++++++++++++
>>   1 file changed, 18 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>> index 38ccd44620d0..e1a4cf1ee51d 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>> @@ -442,3 +442,21 @@ &usb_1_qmpphy {
>>   	vdda-phy-supply = <&vreg_l6b_1p2>;
>>   	vdda-pll-supply = <&vreg_l1b_0p91>;
>>   };
>> +
>> +&mdss {
>> +	status = "okay";
>> +};
>> +
>> +&mdss_mdp {
>> +	status = "okay";
>> +};
>> +
>> +&dsi0 {
> 
> Please prefix the labels with "mdss_" so that you can keep them sorted
> alphabetically.
Why such a change all of a sudden? Only downstream (and sc7280 upstream) 
has mdss_ prefixes for dsi. Plain 'dsiN' is more generic.

Konrad
> 
> THanks,
> Bjorn
> 
>> +	status = "okay";
>> +	vdda-supply = <&vreg_l6b_1p2>;
>> +};
>> +
>> +&dsi0_phy {
>> +	status = "okay";
>> +	vdds-supply = <&vreg_l5b_0p88>;
>> +};
>> -- 
>> 2.35.1
>>

Re: [PATCH v1 3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware

[Krzysztof Kozlowski]

On 07/11/2022 11:46, Konrad Dybcio wrote:
> 
> 
> On 06/11/2022 05:30, Bjorn Andersson wrote:
>> On Fri, Nov 04, 2022 at 04:13:56PM +0300, Dmitry Baryshkov wrote:
>>> Enable MDSS/DPU/DSI0 on SM8450-HDK device. Note, there is no panel
>>> configuration (yet).
>>>
>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>>> ---
>>>   arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 18 ++++++++++++++++++
>>>   1 file changed, 18 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>>> index 38ccd44620d0..e1a4cf1ee51d 100644
>>> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>>> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>>> @@ -442,3 +442,21 @@ &usb_1_qmpphy {
>>>   	vdda-phy-supply = <&vreg_l6b_1p2>;
>>>   	vdda-pll-supply = <&vreg_l1b_0p91>;
>>>   };
>>> +
>>> +&mdss {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&mdss_mdp {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&dsi0 {
>>
>> Please prefix the labels with "mdss_" so that you can keep them sorted
>> alphabetically.
> Why such a change all of a sudden? Only downstream (and sc7280 upstream) 
> has mdss_ prefixes for dsi. 

For keeping the nodes together - this makes review of code and patches
easier.

> Plain 'dsiN' is more generic.

And why the label should be generic? Label should be useful and
descriptive, although not too much, so mdss_dsi still fits in reasonable
choice.

Best regards,
Krzysztof

Re: [PATCH v1 3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware

[Konrad Dybcio]

On 07/11/2022 12:36, Krzysztof Kozlowski wrote:
> On 07/11/2022 11:46, Konrad Dybcio wrote:
>>
>> On 06/11/2022 05:30, Bjorn Andersson wrote:
>>> On Fri, Nov 04, 2022 at 04:13:56PM +0300, Dmitry Baryshkov wrote:
>>>> Enable MDSS/DPU/DSI0 on SM8450-HDK device. Note, there is no panel
>>>> configuration (yet).
>>>>
>>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>>>> ---
>>>>    arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 18 ++++++++++++++++++
>>>>    1 file changed, 18 insertions(+)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>>>> index 38ccd44620d0..e1a4cf1ee51d 100644
>>>> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>>>> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
>>>> @@ -442,3 +442,21 @@ &usb_1_qmpphy {
>>>>    	vdda-phy-supply = <&vreg_l6b_1p2>;
>>>>    	vdda-pll-supply = <&vreg_l1b_0p91>;
>>>>    };
>>>> +
>>>> +&mdss {
>>>> +	status = "okay";
>>>> +};
>>>> +
>>>> +&mdss_mdp {
>>>> +	status = "okay";
>>>> +};
>>>> +
>>>> +&dsi0 {
>>> Please prefix the labels with "mdss_" so that you can keep them sorted
>>> alphabetically.
>> Why such a change all of a sudden? Only downstream (and sc7280 upstream)
>> has mdss_ prefixes for dsi.
> For keeping the nodes together - this makes review of code and patches
> easier.

Ok, I can see the reasoning.


>> Plain 'dsiN' is more generic.
> And why the label should be generic? Label should be useful and
> descriptive, although not too much, so mdss_dsi still fits in reasonable
> choice.

I was under the impression that it should be. But you're right.


Konrad

>
> Best regards,
> Krzysztof
>

[PATCH v1 4/5] arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge

[Dmitry Baryshkov]

From: Vinod Koul <vkoul@kernel.org>

Add the LT9611uxc DSI-HDMI bridge and supplies

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 61 +++++++++++++++++++++++++
 1 file changed, 61 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index e1a4cf1ee51d..9522dd29a38a 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -20,6 +20,28 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	lt9611_1v2: lt9611-vdd12-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_1V2";
+
+		vin-supply = <&vph_pwr>;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	lt9611_3v3: lt9611-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_3V3";
+
+		vin-supply = <&vreg_bob>;
+		gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -349,6 +371,27 @@ vreg_l7e_2p8: ldo7 {
 	};
 };
 
+&i2c9 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	lt9611_codec: hdmi-bridge@2b {
+		compatible = "lontium,lt9611uxc";
+		reg = <0x2b>;
+
+		interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&lt9611_1v2>;
+		vcc-supply = <&lt9611_3v3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
+
+	};
+};
+
 &pcie0 {
 	status = "okay";
 	max-link-speed = <2>;
@@ -394,8 +437,26 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
+&qupv3_id_1 {
+	status = "okay";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <28 4>, <36 4>;
+
+	lt9611_irq_pin: lt9611-irq {
+		pins = "gpio44";
+		function = "gpio";
+		bias-disable;
+	};
+
+	lt9611_rst_pin: lt9611-rst-state {
+		pins = "gpio107";
+		function = "normal";
+
+		output-high;
+		input-disable;
+	};
 };
 
 &uart7 {
-- 
2.35.1

Re: [PATCH v1 4/5] arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge

[Konrad Dybcio]

On 04/11/2022 14:13, Dmitry Baryshkov wrote:
> From: Vinod Koul <vkoul@kernel.org>
>
> Add the LT9611uxc DSI-HDMI bridge and supplies
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 61 +++++++++++++++++++++++++
>   1 file changed, 61 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> index e1a4cf1ee51d..9522dd29a38a 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> @@ -20,6 +20,28 @@ chosen {
>   		stdout-path = "serial0:115200n8";
>   	};
>   
> +	lt9611_1v2: lt9611-vdd12-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_1V2";
> +
> +		vin-supply = <&vph_pwr>;
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	lt9611_3v3: lt9611-3v3 {

The previous node has -regulator, this one doesn't, please keep it 
consistent.


> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_3V3";
> +
> +		vin-supply = <&vreg_bob>;
> +		gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		enable-active-high;
> +	};
> +
>   	vph_pwr: vph-pwr-regulator {
>   		compatible = "regulator-fixed";
>   		regulator-name = "vph_pwr";
> @@ -349,6 +371,27 @@ vreg_l7e_2p8: ldo7 {
>   	};
>   };
>   
> +&i2c9 {
> +	status = "okay";
> +	clock-frequency = <400000>;

Status last, please.


With these fixes:


Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>


Konrad

> +
> +	lt9611_codec: hdmi-bridge@2b {
> +		compatible = "lontium,lt9611uxc";
> +		reg = <0x2b>;
> +
> +		interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
> +
> +		reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
> +
> +		vdd-supply = <&lt9611_1v2>;
> +		vcc-supply = <&lt9611_3v3>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
> +
> +	};
> +};
> +
>   &pcie0 {
>   	status = "okay";
>   	max-link-speed = <2>;
> @@ -394,8 +437,26 @@ &qupv3_id_0 {
>   	status = "okay";
>   };
>   
> +&qupv3_id_1 {
> +	status = "okay";
> +};
> +
>   &tlmm {
>   	gpio-reserved-ranges = <28 4>, <36 4>;
> +
> +	lt9611_irq_pin: lt9611-irq {
> +		pins = "gpio44";
> +		function = "gpio";
> +		bias-disable;
> +	};
> +
> +	lt9611_rst_pin: lt9611-rst-state {
> +		pins = "gpio107";
> +		function = "normal";
> +
> +		output-high;
> +		input-disable;
> +	};
>   };
>   
>   &uart7 {

Re: [PATCH v1 4/5] arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge

[Krzysztof Kozlowski]

On 04/11/2022 09:13, Dmitry Baryshkov wrote:
> From: Vinod Koul <vkoul@kernel.org>
> 
> Add the LT9611uxc DSI-HDMI bridge and supplies
> 
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 61 +++++++++++++++++++++++++
>  1 file changed, 61 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> index e1a4cf1ee51d..9522dd29a38a 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> @@ -20,6 +20,28 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	lt9611_1v2: lt9611-vdd12-regulator {

Node name: drop lt9611

> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_1V2";
> +
> +		vin-supply = <&vph_pwr>;
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	lt9611_3v3: lt9611-3v3 {

Node name: drop lt9611 and add "regulator suffix

> +		compatible = "regulator-fixed";
> +		regulator-name = "LT9611_3V3";
> +
> +		vin-supply = <&vreg_bob>;
> +		gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		enable-active-high;
> +	};
> +
>  	vph_pwr: vph-pwr-regulator {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vph_pwr";
> @@ -349,6 +371,27 @@ vreg_l7e_2p8: ldo7 {
>  	};
>  };
>  
> +&i2c9 {
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	lt9611_codec: hdmi-bridge@2b {
> +		compatible = "lontium,lt9611uxc";
> +		reg = <0x2b>;
> +
> +		interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
> +
> +		reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
> +
> +		vdd-supply = <&lt9611_1v2>;
> +		vcc-supply = <&lt9611_3v3>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
> +
> +	};
> +};
> +
>  &pcie0 {
>  	status = "okay";
>  	max-link-speed = <2>;
> @@ -394,8 +437,26 @@ &qupv3_id_0 {
>  	status = "okay";
>  };
>  
> +&qupv3_id_1 {
> +	status = "okay";
> +};
> +
>  &tlmm {
>  	gpio-reserved-ranges = <28 4>, <36 4>;
> +
> +	lt9611_irq_pin: lt9611-irq {

-state


Best regards,
Krzysztof

[PATCH v1 5/5] arm64: dts: qcom: sm8450-hdk: Enable HDMI Display

[Dmitry Baryshkov]

From: Vinod Koul <vkoul@kernel.org>

Add the HDMI display nodes and link it to DSI. Also enable missing dispcc
nodes

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 45 +++++++++++++++++++++++++
 1 file changed, 45 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index 9522dd29a38a..f37f226e9b11 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -20,6 +20,17 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
+
 	lt9611_1v2: lt9611-vdd12-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "LT9611_1V2";
@@ -389,6 +400,26 @@ lt9611_codec: hdmi-bridge@2b {
 		pinctrl-names = "default";
 		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
 
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
 	};
 };
 
@@ -512,9 +543,23 @@ &mdss_mdp {
 	status = "okay";
 };
 
+&dispcc {
+	status = "okay";
+};
+
 &dsi0 {
 	status = "okay";
 	vdda-supply = <&vreg_l6b_1p2>;
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_a>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+
 };
 
 &dsi0_phy {
-- 
2.35.1

Re: [PATCH v1 5/5] arm64: dts: qcom: sm8450-hdk: Enable HDMI Display

[Konrad Dybcio]

On 04/11/2022 14:13, Dmitry Baryshkov wrote:
> From: Vinod Koul <vkoul@kernel.org>
>
> Add the HDMI display nodes and link it to DSI. Also enable missing dispcc
> nodes
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 45 +++++++++++++++++++++++++
>   1 file changed, 45 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> index 9522dd29a38a..f37f226e9b11 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> @@ -20,6 +20,17 @@ chosen {
>   		stdout-path = "serial0:115200n8";
>   	};
>   
> +	hdmi-out {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con: endpoint {
> +				remote-endpoint = <&lt9611_out>;
> +			};
> +		};
> +	};
> +
>   	lt9611_1v2: lt9611-vdd12-regulator {
>   		compatible = "regulator-fixed";
>   		regulator-name = "LT9611_1V2";
> @@ -389,6 +400,26 @@ lt9611_codec: hdmi-bridge@2b {
>   		pinctrl-names = "default";
>   		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
>   
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +
> +				lt9611_a: endpoint {
> +					remote-endpoint = <&dsi0_out>;
> +				};
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +
> +				lt9611_out: endpoint {
> +					remote-endpoint = <&hdmi_con>;
> +				};
> +			};
> +		};
>   	};
>   };
>   
> @@ -512,9 +543,23 @@ &mdss_mdp {
>   	status = "okay";
>   };
>   
> +&dispcc {
> +	status = "okay";
> +};

Please sort this alphabetically (though I think it's gonna be ok after 
you fix it in 3/5).


With that:


Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>


Konrad

> +
>   &dsi0 {
>   	status = "okay";
>   	vdda-supply = <&vreg_l6b_1p2>;
> +
> +	ports {
> +		port@1 {
> +			endpoint {
> +				remote-endpoint = <&lt9611_a>;
> +				data-lanes = <0 1 2 3>;
> +			};
> +		};
> +	};
> +
>   };
>   
>   &dsi0_phy {

Re: [PATCH v1 5/5] arm64: dts: qcom: sm8450-hdk: Enable HDMI Display

[Krzysztof Kozlowski]

On 04/11/2022 09:13, Dmitry Baryshkov wrote:
> From: Vinod Koul <vkoul@kernel.org>
> 
> Add the HDMI display nodes and link it to DSI. Also enable missing dispcc
> nodes
> 
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

Thank you for your patch. There is something to discuss/improve.

> +&dispcc {
> +	status = "okay";
> +};
> +
>  &dsi0 {
>  	status = "okay";
>  	vdda-supply = <&vreg_l6b_1p2>;
> +
> +	ports {
> +		port@1 {
> +			endpoint {
> +				remote-endpoint = <&lt9611_a>;
> +				data-lanes = <0 1 2 3>;
> +			};
> +		};
> +	};
> +

Drop blank line.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof