[PATCH 1/3] dt-bindings: vendor-prefixes: Add an entry for Cloos

[PATCH 1/3] dt-bindings: vendor-prefixes: Add an entry for Cloos

[Fabio Estevam]

From: Fabio Estevam <festevam@denx.de>

Carl Cloos Schweisstechnik GmbH develops, manufactures and delivers
welding industrial solutions:

https://www.cloos.de/de-en/

Add a vendor prefix entry for it.

Signed-off-by: Fabio Estevam <festevam@denx.de>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 37dd5c54818a..8c6a5283bc46 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -264,6 +264,8 @@ patternProperties:
     description: Cirrus Logic, Inc.
   "^cisco,.*":
     description: Cisco Systems, Inc.
+  "^cloos,.*":
+    description: Carl Cloos Schweisstechnik GmbH.
   "^cloudengines,.*":
     description: Cloud Engines, Inc.
   "^cnm,.*":
-- 
2.25.1

[PATCH 2/3] dt-bindings: arm: fsl: Add an entry for Cloos PHG board

[Fabio Estevam]

From: Fabio Estevam <festevam@denx.de>

Add an entry for the i.MX8MM Cloos PHG board.

Signed-off-by: Fabio Estevam <festevam@denx.de>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index f430eef712c8..05b5276a0e14 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -815,6 +815,7 @@ properties:
           - enum:
               - beacon,imx8mm-beacon-kit  # i.MX8MM Beacon Development Kit
               - boundary,imx8mm-nitrogen8mm  # i.MX8MM Nitrogen Board
+              - cloos,imx8mm-phg          # i.MX8MM Cloos PHG Board
               - dmo,imx8mm-data-modul-edm-sbc # i.MX8MM eDM SBC
               - emtrion,emcon-mx8mm-avari # emCON-MX8MM SoM on Avari Base
               - fsl,imx8mm-ddr4-evk       # i.MX8MM DDR4 EVK Board
-- 
2.25.1

[PATCH 3/3] arm64: dts: imx8mm-phg: Add initial board support

[Fabio Estevam]

From: Fabio Estevam <festevam@denx.de>

Add the initial support for the i.MX8MM Cloos PHG board.

This board uses a imx8mm-tqma8mqml SoM from TQ-Group.

Signed-off-by: Fabio Estevam <festevam@denx.de>
---
 arch/arm64/boot/dts/freescale/Makefile       |   1 +
 arch/arm64/boot/dts/freescale/imx8mm-phg.dts | 266 +++++++++++++++++++
 2 files changed, 267 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-phg.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index c901404197c3..ef6f364eaa18 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -62,6 +62,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl-osm-s.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-phg.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-rdk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phg.dts b/arch/arm64/boot/dts/freescale/imx8mm-phg.dts
new file mode 100644
index 000000000000..e9447738b104
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phg.dts
@@ -0,0 +1,266 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Fabio Estevam <festevam@denx.de>
+ */
+
+/dts-v1/;
+
+#include "imx8mm-tqma8mqml.dtsi"
+
+/ {
+	model = "Cloos i.MX8MM PHG board";
+	compatible = "cloos,imx8mm-phg", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+	aliases {
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc2;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	beeper {
+		compatible = "gpio-beeper";
+		pinctrl-0 = <&pinctrl_beeper>;
+		gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		led-0 {
+			label = "status1";
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-1 {
+			label = "status2";
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "status3";
+			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			label = "run";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-4 {
+			label = "powerled";
+			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_otg_vbus_ctrl>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usdhc2_vmmc: regulator-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		off-on-delay-us = <12000>;
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbphynop1 {
+	power-domains = <&pgc_otg1>;
+};
+
+&usbphynop2 {
+	power-domains = <&pgc_otg2>;
+};
+
+&usbotg1 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
+	assigned-clock-rates = <400000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_400M>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	no-mmc;
+	no-sdio;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_beeper: beepergrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x19
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x82
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x40000002
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x40000002
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x14
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x14
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x14
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x14
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x90
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x90
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x90
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x90
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x14
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x90
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x90
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x14
+			MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22		0x10
+		>;
+	};
+
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19
+			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_otg_vbus_ctrl: otgvbusctrlgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_DATA0_GPIO2_IO2		0x119
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX		0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX		0x140
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x1c4
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+		>;
+	};
+};
-- 
2.25.1

Re: [PATCH 1/3] dt-bindings: vendor-prefixes: Add an entry for Cloos

[Krzysztof Kozlowski]

On 13/11/2022 13:44, Fabio Estevam wrote:
> From: Fabio Estevam <festevam@denx.de>
> 
> Carl Cloos Schweisstechnik GmbH develops, manufactures and delivers
> welding industrial solutions:
> 
> https://www.cloos.de/de-en/
> 
> Add a vendor prefix entry for it.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 2/3] dt-bindings: arm: fsl: Add an entry for Cloos PHG board

[Krzysztof Kozlowski]

On 13/11/2022 13:44, Fabio Estevam wrote:
> From: Fabio Estevam <festevam@denx.de>
> 
> Add an entry for the i.MX8MM Cloos PHG board.
> 
> Signed-off-by: Fabio Estevam <festevam@denx.de>
> ---
>  Documentation/devicetree/bindings/arm/fsl.yaml | 1 +


Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 1/3] dt-bindings: vendor-prefixes: Add an entry for Cloos

[Shawn Guo]

On Sun, Nov 13, 2022 at 09:44:57AM -0300, Fabio Estevam wrote:
> From: Fabio Estevam <festevam@denx.de>
> 
> Carl Cloos Schweisstechnik GmbH develops, manufactures and delivers
> welding industrial solutions:
> 
> https://www.cloos.de/de-en/
> 
> Add a vendor prefix entry for it.
> 
> Signed-off-by: Fabio Estevam <festevam@denx.de>

Applied all, thanks!