[PATCH v4 0/5] arm64: dts: qcom: sm8450-hdk: enable HDMI output

[PATCH v4 0/5] arm64: dts: qcom: sm8450-hdk: enable HDMI output

[Dmitry Baryshkov]

Add device tree nodes for MDSS, DPU and DSI devices on Qualcomm SM8450
platform. Enable these devices and add the HDMI bridge configuration on
SM8450 HDK.

Changes since v3:
- Renamed mdss node to display-subsystem@ (Krzysztof)
- Dropped empty line from the patch4 (Krzysztof)
- Renamed HDMI connector endpoint to hdmi_connector_out

Changes since v2:
- Dropped clock-names from mdss device node
- Fixed pinctrl configuration used by lt9611uxc (Krzysztof)

Changes since v1:
- Reorder properties, making status the last one
- Rename opp nodes to follow the schema
- Renamed display-controller and phy device nodes
- Dropped phy-names for DSI PHYs
- Renamed DSI and DSI PHY labels to include mdss_ prefix
- Renamed 3v3 regulator device node to add -regulator suffix

Dmitry Baryshkov (3):
  arm64: dts: qcom: sm8450: add RPMH_REGULATOR_LEVEL_LOW_SVS_D1
  arm64: dts: qcom: sm8450: add display hardware devices
  arm64: dts: qcom: sm8450-hdk: enable display hardware

Vinod Koul (2):
  arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge
  arm64: dts: qcom: sm8450-hdk: Enable HDMI Display

 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 117 +++++++++
 arch/arm64/boot/dts/qcom/sm8450.dtsi    | 303 +++++++++++++++++++++++-
 include/dt-bindings/power/qcom-rpmpd.h  |   1 +
 3 files changed, 409 insertions(+), 12 deletions(-)

-- 
2.35.1

[PATCH v4 1/5] arm64: dts: qcom: sm8450: add RPMH_REGULATOR_LEVEL_LOW_SVS_D1

[Dmitry Baryshkov]

Add another power saving state used on SM8450. Unfortunately adding it
in proper place causes renumbering of all the opp states in sm8450.dtsi

Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi   | 20 ++++++++++++--------
 include/dt-bindings/power/qcom-rpmpd.h |  1 +
 2 files changed, 13 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index f20db5456765..8cc9f62f7645 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -3211,35 +3211,39 @@ rpmhpd_opp_min_svs: opp2 {
 						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
 					};
 
-					rpmhpd_opp_low_svs: opp3 {
+					rpmhpd_opp_low_svs_d1: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
+					};
+
+					rpmhpd_opp_low_svs: opp4 {
 						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
 					};
 
-					rpmhpd_opp_svs: opp4 {
+					rpmhpd_opp_svs: opp5 {
 						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
 					};
 
-					rpmhpd_opp_svs_l1: opp5 {
+					rpmhpd_opp_svs_l1: opp6 {
 						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
 					};
 
-					rpmhpd_opp_nom: opp6 {
+					rpmhpd_opp_nom: opp7 {
 						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
 					};
 
-					rpmhpd_opp_nom_l1: opp7 {
+					rpmhpd_opp_nom_l1: opp8 {
 						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
 					};
 
-					rpmhpd_opp_nom_l2: opp8 {
+					rpmhpd_opp_nom_l2: opp9 {
 						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
 					};
 
-					rpmhpd_opp_turbo: opp9 {
+					rpmhpd_opp_turbo: opp10 {
 						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
 					};
 
-					rpmhpd_opp_turbo_l1: opp10 {
+					rpmhpd_opp_turbo_l1: opp11 {
 						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
 					};
 				};
diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
index 7b2e4b66419a..701401c8b945 100644
--- a/include/dt-bindings/power/qcom-rpmpd.h
+++ b/include/dt-bindings/power/qcom-rpmpd.h
@@ -174,6 +174,7 @@
 /* SDM845 Power Domain performance levels */
 #define RPMH_REGULATOR_LEVEL_RETENTION	16
 #define RPMH_REGULATOR_LEVEL_MIN_SVS	48
+#define RPMH_REGULATOR_LEVEL_LOW_SVS_D1	56
 #define RPMH_REGULATOR_LEVEL_LOW_SVS	64
 #define RPMH_REGULATOR_LEVEL_SVS	128
 #define RPMH_REGULATOR_LEVEL_SVS_L0	144
-- 
2.35.1

[PATCH v4 2/5] arm64: dts: qcom: sm8450: add display hardware devices

[Dmitry Baryshkov]

Add devices tree nodes describing display hardware on SM8450:
- Display Clock Controller
- MDSS
- MDP
- two DSI controllers and DSI PHYs

This does not provide support for DP controllers present on SM8450.

Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 283 ++++++++++++++++++++++++++-
 1 file changed, 279 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 8cc9f62f7645..3a3819852eae 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -2394,6 +2394,281 @@ camcc: clock-controller@ade0000 {
 			status = "disabled";
 		};
 
+		mdss: display-subsystem@ae00000 {
+			compatible = "qcom,sm8450-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			/* same path used twice */
+			interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>,
+					<&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>;
+			interconnect-names = "mdp0-mem", "mdp1-mem";
+
+			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+			power-domains = <&dispcc MDSS_GDSC>;
+
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&gcc GCC_DISP_SF_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			iommus = <&apps_smmu 0x2800 0x402>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			mdss_mdp: display-controller@ae01000 {
+				compatible = "qcom,sm8450-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp", "vbif";
+
+				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+					<&gcc GCC_DISP_SF_AXI_CLK>,
+					<&dispcc DISP_CC_MDSS_AHB_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_CLK>,
+					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "bus",
+					      "nrt_bus",
+					      "iface",
+					      "lut",
+					      "core",
+					      "vsync";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <19200000>;
+
+				operating-points-v2 = <&mdp_opp_table>;
+				power-domains = <&rpmhpd SM8450_MMCX>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dpu_intf1_out: endpoint {
+							remote-endpoint = <&mdss_dsi0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dpu_intf2_out: endpoint {
+							remote-endpoint = <&mdss_dsi1_in>;
+						};
+					};
+
+				};
+
+				mdp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-172000000 {
+						opp-hz = /bits/ 64 <172000000>;
+						required-opps = <&rpmhpd_opp_low_svs_d1>;
+					};
+
+					opp-200000000 {
+						opp-hz = /bits/ 64 <200000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-325000000 {
+						opp-hz = /bits/ 64 <325000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-375000000 {
+						opp-hz = /bits/ 64 <375000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-500000000 {
+						opp-hz = /bits/ 64 <500000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dsi0: dsi@ae94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae94000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					<&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+				operating-points-v2 = <&mdss_dsi_opp_table>;
+				power-domains = <&rpmhpd SM8450_MMCX>;
+
+				phys = <&mdss_dsi0_phy>;
+				phy-names = "dsi";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi0_in: endpoint {
+							remote-endpoint = <&dpu_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi0_out: endpoint {
+						};
+					};
+				};
+
+				mdss_dsi_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
+			};
+
+			mdss_dsi0_phy: phy@ae94400 {
+				compatible = "qcom,dsi-phy-5nm-8450";
+				reg = <0 0x0ae94400 0 0x200>,
+				      <0 0x0ae94600 0 0x280>,
+				      <0 0x0ae94900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+
+			mdss_dsi1: dsi@ae96000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae96000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <5>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;
+
+				operating-points-v2 = <&mdss_dsi_opp_table>;
+				power-domains = <&rpmhpd SM8450_MMCX>;
+
+				phys = <&mdss_dsi1_phy>;
+				phy-names = "dsi";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi1_in: endpoint {
+							remote-endpoint = <&dpu_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi1_phy: phy@ae96400 {
+				compatible = "qcom,dsi-phy-5nm-8450";
+				reg = <0 0x0ae96400 0 0x200>,
+				      <0 0x0ae96600 0 0x280>,
+				      <0 0x0ae96900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+		};
+
 		dispcc: clock-controller@af00000 {
 			compatible = "qcom,sm8450-dispcc";
 			reg = <0 0x0af00000 0 0x20000>;
@@ -2401,10 +2676,10 @@ dispcc: clock-controller@af00000 {
 				 <&rpmhcc RPMH_CXO_CLK_A>,
 				 <&gcc GCC_DISP_AHB_CLK>,
 				 <&sleep_clk>,
-				 <0>, /* dsi0 */
-				 <0>,
-				 <0>, /* dsi1 */
-				 <0>,
+				 <&mdss_dsi0_phy 0>,
+				 <&mdss_dsi0_phy 1>,
+				 <&mdss_dsi1_phy 0>,
+				 <&mdss_dsi1_phy 1>,
 				 <0>, /* dp0 */
 				 <0>,
 				 <0>, /* dp1 */
-- 
2.35.1

[PATCH v4 3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware

[Dmitry Baryshkov]

Enable MDSS/DPU/DSI0 on SM8450-HDK device.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index 2dd4f8c8f931..75b7aecb7d8e 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -349,6 +349,28 @@ vreg_l7e_2p8: ldo7 {
 	};
 };
 
+&dispcc {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l6b_1p2>;
+	status = "okay";
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l5b_0p88>;
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
 &pcie0 {
 	status = "okay";
 	max-link-speed = <2>;
-- 
2.35.1

[PATCH v4 4/5] arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge

[Dmitry Baryshkov]

From: Vinod Koul <vkoul@kernel.org>

Add the LT9611uxc DSI-HDMI bridge and supplies

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 58 +++++++++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index 75b7aecb7d8e..4f345786352a 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -20,6 +20,28 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	lt9611_1v2: lt9611-vdd12-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_1V2";
+
+		vin-supply = <&vph_pwr>;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	lt9611_3v3: lt9611-3v3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_3V3";
+
+		vin-supply = <&vreg_bob>;
+		gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -353,6 +375,26 @@ &dispcc {
 	status = "okay";
 };
 
+&i2c9 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	lt9611_codec: hdmi-bridge@2b {
+		compatible = "lontium,lt9611uxc";
+		reg = <0x2b>;
+
+		interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&lt9611_1v2>;
+		vcc-supply = <&lt9611_3v3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
+	};
+};
+
 &mdss {
 	status = "okay";
 };
@@ -416,6 +458,10 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
+&qupv3_id_1 {
+	status = "okay";
+};
+
 &sdhc_2 {
 	cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>;
 	pinctrl-names = "default", "sleep";
@@ -431,6 +477,18 @@ &sdhc_2 {
 &tlmm {
 	gpio-reserved-ranges = <28 4>, <36 4>;
 
+	lt9611_irq_pin: lt9611-irq-state {
+		pins = "gpio44";
+		function = "gpio";
+		bias-disable;
+	};
+
+	lt9611_rst_pin: lt9611-rst-state {
+		pins = "gpio107";
+		function = "gpio";
+		output-high;
+	};
+
 	sdc2_card_det_n: sd-card-det-n-state {
 		pins = "gpio92";
 		function = "gpio";
-- 
2.35.1

[PATCH v4 5/5] arm64: dts: qcom: sm8450-hdk: Enable HDMI Display

[Dmitry Baryshkov]

From: Vinod Koul <vkoul@kernel.org>

Add the HDMI display nodes and link it to DSI.

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 37 +++++++++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index 4f345786352a..166458963c2f 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -20,6 +20,17 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_out: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
+
 	lt9611_1v2: lt9611-vdd12-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "LT9611_1V2";
@@ -392,6 +403,27 @@ lt9611_codec: hdmi-bridge@2b {
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_connector_out>;
+				};
+			};
+		};
 	};
 };
 
@@ -404,6 +436,11 @@ &mdss_dsi0 {
 	status = "okay";
 };
 
+&mdss_dsi0_out {
+	remote-endpoint = <&lt9611_a>;
+	data-lanes = <0 1 2 3>;
+};
+
 &mdss_dsi0_phy {
 	vdds-supply = <&vreg_l5b_0p88>;
 	status = "okay";
-- 
2.35.1

Re: [PATCH v4 0/5] arm64: dts: qcom: sm8450-hdk: enable HDMI output

[Bjorn Andersson]

On Wed, 7 Dec 2022 03:27:58 +0200, Dmitry Baryshkov wrote:
> Add device tree nodes for MDSS, DPU and DSI devices on Qualcomm SM8450
> platform. Enable these devices and add the HDMI bridge configuration on
> SM8450 HDK.
> 
> Changes since v3:
> - Renamed mdss node to display-subsystem@ (Krzysztof)
> - Dropped empty line from the patch4 (Krzysztof)
> - Renamed HDMI connector endpoint to hdmi_connector_out
> 
> [...]

Applied, thanks!

[1/5] arm64: dts: qcom: sm8450: add RPMH_REGULATOR_LEVEL_LOW_SVS_D1
      commit: a5ac24ba17590866cf1ff8fe44cd2738c003d52f
[2/5] arm64: dts: qcom: sm8450: add display hardware devices
      commit: a6dd1206e45a43d7e6c46435437307b051471b69
[3/5] arm64: dts: qcom: sm8450-hdk: enable display hardware
      commit: 928a7b4269634369b152342a37b2809d18774726
[4/5] arm64: dts: qcom: sm8450-hdk: Add LT9611uxc HDMI bridge
      commit: 0cbe8e1953e083f8435bdb5548c3ba59acfcb97e
[5/5] arm64: dts: qcom: sm8450-hdk: Enable HDMI Display
      commit: 0f48b65f716b4fa806fa864ea7f750113f4bd7c9

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>