From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Amit Kucheria <amitk@kernel.org>,
Thara Gopinath <thara.gopinath@gmail.com>,
"Rafael J. Wysocki" <rafael@kernel.org>,
Daniel Lezcano <daniel.lezcano@linaro.org>,
Zhang Rui <rui.zhang@intel.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>,
linux-arm-msm@vger.kernel.org, linux-pm@vger.kernel.org,
devicetree@vger.kernel.org
Subject: [PATCH v4 20/20] ARM: dts: qcom-apq8084: specify per-sensor calibration cells
Date: Wed, 21 Dec 2022 04:05:20 +0200 [thread overview]
Message-ID: <20221221020520.1326964-21-dmitry.baryshkov@linaro.org> (raw)
In-Reply-To: <20221221020520.1326964-1-dmitry.baryshkov@linaro.org>
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm/boot/dts/qcom-apq8084.dtsi | 313 +++++++++++++++++++++++++++-
1 file changed, 307 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index fe30abfff90a..22e56ee82a20 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -249,11 +249,260 @@ qfprom: qfprom@fc4bc000 {
reg = <0xfc4bc000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
- tsens_calib: calib@d0 {
- reg = <0xd0 0x18>;
+
+ tsens_base1: base1@d0 {
+ reg = <0xd0 0x1>;
+ bits = <0 8>;
+ };
+
+ tsens_s0_p1: s0-p1@d1 {
+ reg = <0xd1 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s1_p1: s1-p1@d2 {
+ reg = <0xd1 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s2_p1: s2-p1@d2 {
+ reg = <0xd2 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s3_p1: s3-p1@d3 {
+ reg = <0xd3 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s4_p1: s4-p1@d4 {
+ reg = <0xd4 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s5_p1: s5-p1@d4 {
+ reg = <0xd4 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s6_p1: s6-p1@d5 {
+ reg = <0xd5 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s7_p1: s7-p1@d6 {
+ reg = <0xd6 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s8_p1: s8-p1@d7 {
+ reg = <0xd7 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_mode: mode@d7 {
+ reg = <0xd7 0x1>;
+ bits = <6 2>;
+ };
+
+ tsens_s9_p1: s9-p1@d8 {
+ reg = <0xd8 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s10_p1: s10_p1@d8 {
+ reg = <0xd8 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_base2: base2@d9 {
+ reg = <0xd9 0x2>;
+ bits = <4 8>;
+ };
+
+ tsens_s0_p2: s0-p2@da {
+ reg = <0xda 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s1_p2: s1-p2@db {
+ reg = <0xdb 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s2_p2: s2-p2@dc {
+ reg = <0xdc 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s3_p2: s3-p2@dc {
+ reg = <0xdc 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s4_p2: s4-p2@dd {
+ reg = <0xdd 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s5_p2: s5-p2@de {
+ reg = <0xde 0x2>;
+ bits = <2 6>;
+ };
+
+ tsens_s6_p2: s6-p2@df {
+ reg = <0xdf 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s7_p2: s7-p2@e0 {
+ reg = <0xe0 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s8_p2: s8-p2@e0 {
+ reg = <0xe0 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s9_p2: s9-p2@e1 {
+ reg = <0xe1 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s10_p2: s10_p2@e2 {
+ reg = <0xe2 0x2>;
+ bits = <2 6>;
+ };
+
+ tsens_s5_p2_backup: s5-p2_backup@e3 {
+ reg = <0xe3 0x2>;
+ bits = <0 6>;
+ };
+
+ tsens_mode_backup: mode_backup@e3 {
+ reg = <0xe3 0x1>;
+ bits = <6 2>;
+ };
+
+ tsens_s6_p2_backup: s6-p2_backup@e4 {
+ reg = <0xe4 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s7_p2_backup: s7-p2_backup@e4 {
+ reg = <0xe4 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s8_p2_backup: s8-p2_backup@e5 {
+ reg = <0xe5 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s9_p2_backup: s9-p2_backup@e6 {
+ reg = <0xe6 0x2>;
+ bits = <2 6>;
+ };
+
+ tsens_s10_p2_backup: s10_p2_backup@e7 {
+ reg = <0xe7 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_base1_backup: base1_backup@440 {
+ reg = <0x440 0x1>;
+ bits = <0 8>;
+ };
+
+ tsens_s0_p1_backup: s0-p1_backup@441 {
+ reg = <0x441 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s1_p1_backup: s1-p1_backup@442 {
+ reg = <0x441 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s2_p1_backup: s2-p1_backup@442 {
+ reg = <0x442 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s3_p1_backup: s3-p1_backup@443 {
+ reg = <0x443 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s4_p1_backup: s4-p1_backup@444 {
+ reg = <0x444 0x1>;
+ bits = <0 6>;
};
- tsens_backup: backup@440 {
- reg = <0x440 0x10>;
+
+ tsens_s5_p1_backup: s5-p1_backup@444 {
+ reg = <0x444 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s6_p1_backup: s6-p1_backup@445 {
+ reg = <0x445 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s7_p1_backup: s7-p1_backup@446 {
+ reg = <0x446 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_use_backup: use_backup@447 {
+ reg = <0x447 0x1>;
+ bits = <5 3>;
+ };
+
+ tsens_s8_p1_backup: s8-p1_backup@448 {
+ reg = <0x448 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s9_p1_backup: s9-p1_backup@448 {
+ reg = <0x448 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s10_p1_backup: s10_p1_backup@449 {
+ reg = <0x449 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_base2_backup: base2_backup@44a {
+ reg = <0x44a 0x2>;
+ bits = <2 8>;
+ };
+
+ tsens_s0_p2_backup: s0-p2_backup@44b {
+ reg = <0x44b 0x3>;
+ bits = <2 6>;
+ };
+
+ tsens_s1_p2_backup: s1-p2_backup@44c {
+ reg = <0x44c 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s2_p2_backup: s2-p2_backup@44c {
+ reg = <0x44c 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s3_p2_backup: s3-p2_backup@44d {
+ reg = <0x44d 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s4_p2_backup: s4-p2_backup@44e {
+ reg = <0x44e 0x1>;
+ bits = <2 6>;
};
};
@@ -261,8 +510,60 @@ tsens: thermal-sensor@fc4a8000 {
compatible = "qcom,msm8974-tsens", "qcom,tsens-v0_1";
reg = <0xfc4a9000 0x1000>, /* TM */
<0xfc4a8000 0x1000>; /* SROT */
- nvmem-cells = <&tsens_calib>, <&tsens_backup>;
- nvmem-cell-names = "calib", "calib_backup";
+ nvmem-cells = <&tsens_mode>,
+ <&tsens_base1>, <&tsens_base2>,
+ <&tsens_s0_p1>, <&tsens_s0_p2>,
+ <&tsens_s1_p1>, <&tsens_s1_p2>,
+ <&tsens_s2_p1>, <&tsens_s2_p2>,
+ <&tsens_s3_p1>, <&tsens_s3_p2>,
+ <&tsens_s4_p1>, <&tsens_s4_p2>,
+ <&tsens_s5_p1>, <&tsens_s5_p2>,
+ <&tsens_s6_p1>, <&tsens_s6_p2>,
+ <&tsens_s7_p1>, <&tsens_s7_p2>,
+ <&tsens_s8_p1>, <&tsens_s8_p2>,
+ <&tsens_s9_p1>, <&tsens_s9_p2>,
+ <&tsens_s10_p1>, <&tsens_s10_p2>,
+ <&tsens_use_backup>,
+ <&tsens_mode_backup>,
+ <&tsens_base1_backup>, <&tsens_base2_backup>,
+ <&tsens_s0_p1_backup>, <&tsens_s0_p2_backup>,
+ <&tsens_s1_p1_backup>, <&tsens_s1_p2_backup>,
+ <&tsens_s2_p1_backup>, <&tsens_s2_p2_backup>,
+ <&tsens_s3_p1_backup>, <&tsens_s3_p2_backup>,
+ <&tsens_s4_p1_backup>, <&tsens_s4_p2_backup>,
+ <&tsens_s5_p1_backup>, <&tsens_s5_p2_backup>,
+ <&tsens_s6_p1_backup>, <&tsens_s6_p2_backup>,
+ <&tsens_s7_p1_backup>, <&tsens_s7_p2_backup>,
+ <&tsens_s8_p1_backup>, <&tsens_s8_p2_backup>,
+ <&tsens_s9_p1_backup>, <&tsens_s9_p2_backup>,
+ <&tsens_s10_p1_backup>, <&tsens_s10_p2_backup>;
+ nvmem-cell-names = "mode",
+ "base1", "base2",
+ "s0_p1", "s0_p2",
+ "s1_p1", "s1_p2",
+ "s2_p1", "s2_p2",
+ "s3_p1", "s3_p2",
+ "s4_p1", "s4_p2",
+ "s5_p1", "s5_p2",
+ "s6_p1", "s6_p2",
+ "s7_p1", "s7_p2",
+ "s8_p1", "s8_p2",
+ "s9_p1", "s9_p2",
+ "s10_p1", "s10_p2",
+ "use_backup",
+ "mode_backup",
+ "base1_backup", "base2_backup",
+ "s0_p1_backup", "s0_p2_backup",
+ "s1_p1_backup", "s1_p2_backup",
+ "s2_p1_backup", "s2_p2_backup",
+ "s3_p1_backup", "s3_p2_backup",
+ "s4_p1_backup", "s4_p2_backup",
+ "s5_p1_backup", "s5_p2_backup",
+ "s6_p1_backup", "s6_p2_backup",
+ "s7_p1_backup", "s7_p2_backup",
+ "s8_p1_backup", "s8_p2_backup",
+ "s9_p1_backup", "s9_p2_backup",
+ "s10_p1_backup", "s10_p2_backup";
#qcom,sensors = <11>;
interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "uplow";
--
2.35.1
next prev parent reply other threads:[~2022-12-21 2:06 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-12-21 2:05 [PATCH v4 00/15] thermal/drivers/tsens: specify nvmem cells in DT rather than parsing them manually Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 01/20] dt-bindings: thermal: tsens: add msm8956 compat Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 02/20] dt-bindings: thermal: tsens: support per-sensor calibration cells Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 03/20] dt-bindings: thermal: tsens: add per-sensor cells for msm8974 Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 04/20] thermal/drivers/tsens: Drop unnecessary hw_ids Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 05/20] thermal/drivers/tsens: Drop msm8976-specific defines Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 06/20] thermal/drivers/tsens: Sort out msm8976 vs msm8956 data Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 07/20] thermal/drivers/tsens: limit num_sensors to 9 Dmitry Baryshkov
2022-12-21 15:45 ` Daniel Lezcano
2022-12-21 18:05 ` Dmitry Baryshkov
2022-12-21 18:15 ` Daniel Lezcano
2022-12-21 19:42 ` Dmitry Baryshkov
2022-12-21 20:13 ` Konrad Dybcio
2022-12-21 2:05 ` [PATCH v4 08/20] thermal/drivers/tsens: fix slope values for msm8939 Dmitry Baryshkov
2022-12-21 20:14 ` Konrad Dybcio
2022-12-21 2:05 ` [PATCH v4 09/20] thermal/drivers/tsens: Support using nvmem cells for calibration data Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 10/20] thermal/drivers/tsens: Support using nvmem cells for msm8974 calibration Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 11/20] thermal/drivers/tsens: Rework legacy calibration data parsers Dmitry Baryshkov
2022-12-21 14:08 ` kernel test robot
2022-12-21 2:05 ` [PATCH v4 12/20] thermal/drivers/tsens: Drop single-cell code for mdm9607 Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 13/20] thermal/drivers/tsens: Drop single-cell code for msm8939 Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 14/20] thermal/drivers/tsens: Drop single-cell code for msm8976/msm8956 Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 15/20] arm64: dts: qcom: msm8956: use SoC-specific compat for tsens Dmitry Baryshkov
2022-12-21 20:15 ` Konrad Dybcio
2022-12-21 2:05 ` [PATCH v4 16/20] arm64: dts: qcom: msm8916: specify per-sensor calibration cells Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 17/20] arm64: dts: qcom: msm8976: " Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 18/20] arm64: dts: qcom: qcs404: " Dmitry Baryshkov
2022-12-21 2:05 ` [PATCH v4 19/20] ARM: dts: qcom-msm8974: " Dmitry Baryshkov
2022-12-21 2:05 ` Dmitry Baryshkov [this message]
2022-12-21 15:37 ` [PATCH v4 00/15] thermal/drivers/tsens: specify nvmem cells in DT rather than parsing them manually Daniel Lezcano
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221221020520.1326964-21-dmitry.baryshkov@linaro.org \
--to=dmitry.baryshkov@linaro.org \
--cc=agross@kernel.org \
--cc=amitk@kernel.org \
--cc=andersson@kernel.org \
--cc=bryan.odonoghue@linaro.org \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=rafael@kernel.org \
--cc=robh+dt@kernel.org \
--cc=rui.zhang@intel.com \
--cc=thara.gopinath@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).