[PATCH] arm64: dts: qcom: sc8280xp-x13s: enable eDP display

[Johan Hovold <johan+linaro@kernel.org>]

Enable the eDP display on MDSS0 DP3, including backlight control.

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
---

This one depends on the sc8280xp display patches:

	https://lore.kernel.org/lkml/20230111035906.2975494-1-quic_bjorande@quicinc.com/T/#mbcdfc826df6683a71d80bab5d86645ba81b02d52

Johan


 .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts    | 75 ++++++++++++++++++-
 1 file changed, 73 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
index 23c1ca44ec11..ef17ef90d1f0 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
@@ -47,7 +47,7 @@ wcd938x: audio-codec {
 		#sound-dai-cells = <1>;
 	};
 
-	backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pmc8280c_lpg 3 1000000>;
 		enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
@@ -72,6 +72,22 @@ switch-lid {
 		};
 	};
 
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VCC3LCD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_reg_en>;
+
+		regulator-boot-on;
+	};
+
 	vreg_edp_bl: regulator-edp-bl {
 		compatible = "regulator-fixed";
 
@@ -259,7 +275,6 @@ vreg_l6b: ldo6 {
 			regulator-max-microvolt = <880000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-boot-on;
-			regulator-always-on;	/* FIXME: VDD_A_EDP_0_0P9 */
 		};
 	};
 
@@ -340,6 +355,55 @@ vreg_l9d: ldo9 {
 	};
 };
 
+&dispcc0 {
+	status = "okay";
+};
+
+&mdss0 {
+	status = "okay";
+};
+
+&mdss0_dp3 {
+	compatible = "qcom,sc8280xp-edp";
+
+	data-lanes = <0 1 2 3>;
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+
+			backlight = <&backlight>;
+			power-supply = <&vreg_edp_3p3>;
+
+			ports {
+				port {
+					edp_panel_in: endpoint {
+						remote-endpoint = <&mdss0_dp3_out>;
+					};
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			reg = <1>;
+			mdss0_dp3_out: endpoint {
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+};
+
+&mdss0_dp3_phy {
+	vdda-phy-supply = <&vreg_l6b>;
+	vdda-pll-supply = <&vreg_l3b>;
+
+	status = "okay";
+};
+
 &pcie2a {
 	perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
 	wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
@@ -902,6 +966,13 @@ hastings_reg_en: hastings-reg-en-state {
 &tlmm {
 	gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
 
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio25";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
 	hall_int_n_default: hall-int-n-state {
 		pins = "gpio107";
 		function = "gpio";
-- 
2.38.2