From: Durai Manickam KR <durai.manickamkr@microchip.com>
To: <Hari.PrasathGE@microchip.com>,
<balamanikandan.gunasundar@microchip.com>,
<manikandan.m@microchip.com>, <varshini.rajendran@microchip.com>,
<dharma.b@microchip.com>, <nayabbasha.sayed@microchip.com>,
<balakrishnan.s@microchip.com>, <claudiu.beznea@microchip.com>,
<cristian.birsan@microchip.com>, <nicolas.ferre@microchip.com>,
<krzysztof.kozlowski@linaro.org>, <alexandre.belloni@bootlin.com>,
<davem@davemloft.net>, <arnd@arndb.de>, <olof@lixom.net>,
<soc@kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>,
<Kavyasree.Kotagiri@microchip.com>,
<Horatiu.Vultur@microchip.com>, <robh+dt@kernel.org>,
<andrew@lunn.ch>, <michael@walle.cc>, <jerry.ray@microchip.com>
Cc: Durai Manickam KR <durai.manickamkr@microchip.com>
Subject: [PATCH v4 2/8] ARM: dts: at91: sam9x60: move flexcom definitions
Date: Thu, 12 Jan 2023 16:32:02 +0530 [thread overview]
Message-ID: <20230112110208.97946-3-durai.manickamkr@microchip.com> (raw)
In-Reply-To: <20230112110208.97946-1-durai.manickamkr@microchip.com>
Move the flexcom definitions from board specific DTS file
to the SoC specific DTSI file for sam9x60ek.
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Signed-off-by: Hari Prasath Gujulan Elango <Hari.PrasathGE@microchip.com>
[durai.manickamkr@microchip.com: Logical split-up of this patch]
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
---
arch/arm/boot/dts/at91-sam9x60ek.dts | 33 +------------------
arch/arm/boot/dts/sam9x60.dtsi | 49 ++++++++++++++++++++++++++++
2 files changed, 50 insertions(+), 32 deletions(-)
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index cf5d786531f2..4ff84633dd43 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -207,15 +207,10 @@ &flx0 {
status = "okay";
i2c0: i2c@600 {
- compatible = "microchip,sam9x60-i2c";
- reg = <0x600 0x200>;
- interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx0_default>;
- atmel,fifo-size = <16>;
i2c-analog-filter;
i2c-digital-filter;
i2c-digital-filter-width-ns = <35>;
@@ -235,14 +230,8 @@ &flx4 {
status = "disabled";
spi4: spi@400 {
- compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
- reg = <0x400 0x200>;
- interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
- clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
- clock-names = "spi_clk";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
- atmel,fifo-size = <16>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -254,23 +243,8 @@ &flx5 {
status = "okay";
uart5: serial@200 {
- compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
- reg = <0x200 0x200>;
- atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
- interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
- dmas = <&dma0
- (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
- AT91_XDMAC_DT_PERID(10))>,
- <&dma0
- (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
- AT91_XDMAC_DT_PERID(11))>;
- dma-names = "tx", "rx";
- clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
- clock-names = "usart";
- pinctrl-0 = <&pinctrl_flx5_default>;
pinctrl-names = "default";
- atmel,use-dma-rx;
- atmel,use-dma-tx;
+ pinctrl-0 = <&pinctrl_flx5_default>;
status = "okay";
};
};
@@ -280,15 +254,10 @@ &flx6 {
status = "okay";
i2c6: i2c@600 {
- compatible = "microchip,sam9x60-i2c";
- reg = <0x600 0x200>;
- interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx6_default>;
- atmel,fifo-size = <16>;
i2c-analog-filter;
i2c-digital-filter;
i2c-digital-filter-width-ns = <35>;
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index 8f5477e307dd..74c90158801b 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -170,6 +170,16 @@ flx4: flexcom@f0000000 {
#size-cells = <1>;
ranges = <0x0 0xf0000000 0x800>;
status = "disabled";
+
+ spi4: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ clock-names = "spi_clk";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx5: flexcom@f0004000 {
@@ -180,6 +190,27 @@ flx5: flexcom@f0004000 {
#size-cells = <1>;
ranges = <0x0 0xf0004000 0x800>;
status = "disabled";
+
+ uart5: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "disabled";
+ };
};
dma0: dma-controller@f0008000 {
@@ -379,6 +410,15 @@ flx6: flexcom@f8010000 {
#size-cells = <1>;
ranges = <0x0 0xf8010000 0x800>;
status = "disabled";
+
+ i2c6: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx7: flexcom@f8014000 {
@@ -409,6 +449,15 @@ flx0: flexcom@f801c000 {
#size-cells = <1>;
ranges = <0x0 0xf801c000 0x800>;
status = "disabled";
+
+ i2c0: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx1: flexcom@f8020000 {
--
2.25.1
next prev parent reply other threads:[~2023-01-12 11:11 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-12 11:02 [PATCH v4 0/8] Add support for sam9x60 curiosity board Durai Manickam KR
2023-01-12 11:02 ` [PATCH v4 1/8] ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom functions Durai Manickam KR
2023-01-16 9:52 ` Claudiu.Beznea
2023-01-12 11:02 ` Durai Manickam KR [this message]
2023-01-16 9:50 ` [PATCH v4 2/8] ARM: dts: at91: sam9x60: move flexcom definitions Claudiu.Beznea
2023-01-12 11:02 ` [PATCH v4 3/8] ARM: dts: at91: sam9x60: fix spi4 node Durai Manickam KR
2023-01-16 9:52 ` Claudiu.Beznea
2023-01-12 11:02 ` [PATCH v4 4/8] ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART Durai Manickam KR
2023-01-16 9:53 ` Claudiu.Beznea
2023-01-12 11:02 ` [PATCH v4 5/8] ARM: dts: at91: sam9x60: Add DMA bindings for the flexcom nodes Durai Manickam KR
2023-01-16 9:56 ` Claudiu.Beznea
2023-01-12 11:02 ` [PATCH v4 6/8] ARM: dts: at91: sam9x60: Add missing flexcom definitions Durai Manickam KR
2023-01-12 11:02 ` [PATCH v4 7/8] dt-bindings: arm: at91: Add info on sam9x60 curiosity Durai Manickam KR
2023-01-12 11:37 ` Krzysztof Kozlowski
2023-01-12 11:02 ` [PATCH v4 8/8] ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60 curiosity board Durai Manickam KR
2023-01-16 10:49 ` Claudiu.Beznea
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230112110208.97946-3-durai.manickamkr@microchip.com \
--to=durai.manickamkr@microchip.com \
--cc=Hari.PrasathGE@microchip.com \
--cc=Horatiu.Vultur@microchip.com \
--cc=Kavyasree.Kotagiri@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=andrew@lunn.ch \
--cc=arnd@arndb.de \
--cc=balakrishnan.s@microchip.com \
--cc=balamanikandan.gunasundar@microchip.com \
--cc=claudiu.beznea@microchip.com \
--cc=cristian.birsan@microchip.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=dharma.b@microchip.com \
--cc=jerry.ray@microchip.com \
--cc=krzysztof.kozlowski@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=manikandan.m@microchip.com \
--cc=michael@walle.cc \
--cc=nayabbasha.sayed@microchip.com \
--cc=nicolas.ferre@microchip.com \
--cc=olof@lixom.net \
--cc=robh+dt@kernel.org \
--cc=soc@kernel.org \
--cc=varshini.rajendran@microchip.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).