From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
To: agross@kernel.org, andersson@kernel.org,
konrad.dybcio@linaro.org, djakov@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org
Cc: bryan.odonoghue@linaro.org, linux-arm-msm@vger.kernel.org,
linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, benl@squareup.com,
shawn.guo@linaro.org, fabien.parent@linaro.org,
leo.yan@linaro.org, dmitry.baryshkov@linaro.org,
Jun Nie <jun.nie@linaro.org>,
James Willcox <jwillcox@squareup.com>,
Joseph Gates <jgates@squareup.com>, Max Chen <mchen@squareup.com>,
Zac Crosby <zac@squareup.com>
Subject: [PATCH v3 7/8] arm64: dts: qcom: Add Square apq8039-t2 board
Date: Tue, 17 Jan 2023 02:48:45 +0000 [thread overview]
Message-ID: <20230117024846.1367794-8-bryan.odonoghue@linaro.org> (raw)
In-Reply-To: <20230117024846.1367794-1-bryan.odonoghue@linaro.org>
The apq8039-t2 is an apq8039 based board paired with a wcn3680b WiFi
chipset.
Co-developed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Co-developed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Co-developed-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Benjamin Li <benl@squareup.com>
Co-developed-by: James Willcox <jwillcox@squareup.com>
Signed-off-by: James Willcox <jwillcox@squareup.com>
Co-developed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Co-developed-by: Joseph Gates <jgates@squareup.com>
Signed-off-by: Joseph Gates <jgates@squareup.com>
Co-developed-by: Max Chen <mchen@squareup.com>
Signed-off-by: Max Chen <mchen@squareup.com>
Co-developed-by: Zac Crosby <zac@squareup.com>
Signed-off-by: Zac Crosby <zac@squareup.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/apq8039-t2.dts | 557 ++++++++++++++++++++++++
2 files changed, 558 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/apq8039-t2.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index e442a81895d04..5c47d1fb50b01 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb
+dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
diff --git a/arch/arm64/boot/dts/qcom/apq8039-t2.dts b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
new file mode 100644
index 0000000000000..21f5a21f76135
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
@@ -0,0 +1,557 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020-2023, Linaro Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include "msm8939.dtsi"
+#include "msm8939-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
+
+/ {
+ model = "Square, Inc. T2 Devkit";
+ compatible = "square,apq8039-t2", "qcom,msm8939";
+
+ qcom,board-id = <0x53 0x54>;
+ qcom,msm-id = <239 0>, <239 0x30000>, <241 0x30000>, <263 0x30000>;
+
+ aliases {
+ mmc0 = &sdhc_1;
+ mmc1 = &sdhc_2;
+ serial0 = &blsp1_uart1;
+ serial1 = &blsp1_uart2;
+ };
+
+ bl: backlight {
+ compatible = "gpio-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ lcd_iovcc_reg: lcd-iovcc-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_iovcc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_iovcc_reg>;
+ gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <300>;
+ enable-active-high;
+ };
+
+ lcd_avdd_reg: lcd-avdd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_avdd";
+ regulator-min-microvolt = <5600000>;
+ regulator-max-microvolt = <5600000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_avdd_reg>;
+ gpio = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <300>;
+ enable-active-high;
+ };
+
+ lcd_avee_reg: lcd-avee-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_avee";
+ regulator-min-microvolt = <5600000>;
+ regulator-max-microvolt = <5600000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_avee_reg>;
+ gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <300>;
+ enable-active-high;
+ };
+
+ pp_spe_3v3_reg: pp-spe-3v3-regulator {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&tlmm_spe_reg>;
+ regulator-name = "pp_spe_3v3";
+ gpio = <&tlmm 108 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <0>;
+ enable-active-high;
+ };
+
+ pp_crq_3v3_reg: pp-crq-3v3-regulator {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&tlmm_crq_reg>;
+ regulator-name = "pp_crq_3v3";
+ gpio = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <0>;
+ enable-active-high;
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp_i2c1 {
+ status = "okay";
+};
+
+&blsp_i2c2 {
+ status = "okay";
+};
+
+&blsp_i2c3 {
+ status = "okay";
+
+ typec: tps6598x@38 {
+ compatible = "ti,tps6598x";
+ reg = <0x38>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <107 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "irq";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&typec_irq>;
+
+ typec_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ port {
+ typec_ep: endpoint {
+ remote-endpoint = <&otg_ep>;
+ };
+ };
+ };
+ };
+};
+
+&blsp_i2c5 {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart1_default>;
+ pinctrl-1 = <&blsp1_uart1_sleep>;
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart2_default>;
+ pinctrl-1 = <&blsp1_uart2_sleep>;
+ status = "okay";
+};
+
+&lpass {
+ status = "okay";
+};
+
+/*
+ * Line names are taken from the schematic of T2, Ver X03.
+ * July 14, 2018. Page 4 in particular.
+ */
+
+&tlmm {
+ gpio-line-names =
+ "APQ_UART1_TX", /* GPIO_0 */
+ "APQ_UART1_RX",
+ "APQ_I2C1_SDA",
+ "APQ_I2C1_SCL",
+ "APQ_UART2_TX_1V8",
+ "APQ_UART2_RX_1V8",
+ "APQ_I2C2_SDA",
+ "APQ_I2C2_SCL",
+ "NC",
+ "APQ_LCD_IOVCC_EN",
+ "APQ_I2C3_SDA", /* GPIO_10 */
+ "APQ_I2C3_SCL",
+ "TOUCH_RST_1V8_L",
+ "NC",
+ "APQ_I2C4_SDA",
+ "APQ_I2C4_SCL",
+ "APQ_ID5",
+ "USB_DISCONNECT",
+ "APQ_I2C5_SDA",
+ "APQ_I2C5_SCL",
+ "APQ_USBC_SPI_MOSI", /* GPIO_20 */
+ "APQ_USBC_SPI_MISO",
+ "APQ_USBC_SPI_SS_L",
+ "APQ_USBC_SPI_CLK",
+ "APQ_LCD_TE0",
+ "APQ_LCD_RST_L",
+ "NC",
+ "NC",
+ "ACCELEROMETER_INT1",
+ "APQ_CAM_I2C0_SDA",
+ "APQ_CAM_I2C0_SCL", /* GPIO_30 */
+ "ACCELEROMETER_INT2",
+ "NC",
+ "NC",
+ "NC",
+ "APQ_K21_RST_1V8_L",
+ "NC",
+ "APQ_EDL_1V8",
+ "TP145",
+ "BT_SSBI",
+ "NC", /* GPIO_40 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "BT_CTRL",
+ "BT_DAT",
+ "PWR_GPIO_IN",
+ "PWR_GPIO_OUT", /* GPIO_50 */
+ "CARD_DET_MLB_L",
+ "HALL_SENSOR",
+ "TP63",
+ "TP64",
+ "TP65",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO_60 */
+ "NC",
+ "APQ_K21_GPIO0_1V8",
+ "CDC_PDM_CLK",
+ "CDC_PDM_SYNC",
+ "CDC_PDM_TX",
+ "CDC_PDM_RX0",
+ "CDC_PDM_RX1",
+ "CDC_PDM_RX2",
+ "APQ_K21_GPIO1_1V8",
+ "NC", /* GPIO_70 */
+ "APQ_HUB_SEL_1V8",
+ "APQ_K21_GPIO2_1V8",
+ "APQ_K21_GPIO3_1V8",
+ "APQ_ID0",
+ "APQ_ID1",
+ "APQ_ID2",
+ "APQ_ID3",
+ "APQ_ID4",
+ "APQ_HUB_SUSP_IND",
+ "BOOT_CONFIG_0", /* GPIO_80 */
+ "BOOT_CONFIG_1",
+ "BOOT_CONFIG_2",
+ "BOOT_CONFIG_3",
+ "NC",
+ "NC",
+ "APQ_LCD_AVDD_EN",
+ "APQ_LCD_AVEE_EN",
+ "TP70",
+ "NC",
+ "APQ_DEBUG0", /* GPIO_90 */
+ "APQ_DEBUG1",
+ "APQ_DEBUG2",
+ "APQ_DEBUG3",
+ "TP165",
+ "NC",
+ "APQ_LNA_PWR_EN",
+ "NC",
+ "APQ_LCD_BL_EN",
+ "NC",
+ "APQ_LCD_ID0", /* GPIO_100 */
+ "APQ_LCD_ID1",
+ "USBC_GPIO5_1V8",
+ "NC",
+ "NC",
+ "NC",
+ "APQ_HUB_RST_1V8_L",
+ "USBC_I2C_IRQ_1V8_L",
+ "SPE_PWR_EN",
+ "NC",
+ "APQ_USB_ID", /* GPIO_110 */
+ "APQ_EXT_BUCK_VSEL",
+ "APQ_USB_ID_OUT",
+ "NC",
+ "PRNT_RST_L",
+ "APQ_CRQ_I2C_RDY_1V8",
+ "TYPEC_RST_1V8_H",
+ "CHG_BACKPWR_EN",
+ "CHG_PROCHOT_L",
+ "NC",
+ "USBC_GPIO7_1V8", /* GPIO_120 */
+ "NC";
+
+ blsp1_uart1_default: blsp1-uart1-default-state {
+ pins = "gpio0", "gpio1";
+ function = "blsp_uart1";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ blsp1_uart1_sleep: blsp1-uart1-sleep-state {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ pinctrl_lcd_iovcc_reg: lcd-iovcc-reg-state {
+ pins = "gpio9";
+ function = "gpio";
+ };
+
+ tlmm_crq_reg: tlmm-crq-reg-state {
+ function = "gpio";
+ pins = "gpio12";
+ output-high;
+ };
+
+ pinctrl_otg_host: otg-host-state {
+ function = "gpio";
+ pins = "gpio17";
+ output-low;
+ };
+
+ pinctrl_otg_device: otg-device-state {
+ function = "gpio";
+ pins = "gpio17";
+ output-low;
+ };
+
+ pinctrl_otg_default: otg-default-state {
+ function = "gpio";
+ pins = "gpio17";
+ output-high;
+ };
+
+ pinctrl_lcd_rst: lcd-rst-state {
+ pins = "gpio25";
+ function = "gpio";
+ };
+
+ sq_spe_enable: sq-spe-enable-state {
+ pins = "gpio35";
+ function = "gpio";
+ output-low;
+ };
+
+ pinctrl_lcd_avdd_reg: lcd-avdd-reg-state {
+ pins = "gpio86";
+ function = "gpio";
+ };
+
+ pinctrl_lcd_avee_reg: lcd-avee-reg-state {
+ pins = "gpio87";
+ function = "gpio";
+ };
+
+ pinctrl_backlight: backlight-state {
+ pins = "gpio98";
+ function = "gpio";
+ };
+
+ typec_irq: typec-irq-state {
+ function = "gpio";
+ pins = "gpio107";
+ bias-pull-up;
+ input-enable;
+ };
+
+ tlmm_spe_reg: tlmm-spe-reg-state {
+ pins = "gpio108";
+ function = "gpio";
+ output-high;
+ };
+
+ ext_buck_vsel_reg: ext-buck-vsel-reg-state {
+ function = "gpio";
+ pins = "gpio111";
+ drive-strength = <2>;
+ };
+};
+
+&pm8916_gpios {
+ gpio-line-names =
+ "PM_GPIO1", /* WIFI_GPIO1_PRE */
+ "PM_GPIO2", /* WIFI_GPIO2_PRE */
+ "PM_GPIO3",
+ "PM_GPIO4";
+};
+
+&pronto {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcnss_pin_a>;
+ status = "okay";
+
+ iris {
+ compatible = "qcom,wcn3680";
+ };
+};
+
+&smd_rpm_regulators {
+ vdd_l1_l2_l3-supply = <&pm8916_s3>;
+ vdd_l4_l5_l6-supply = <&pm8916_s4>;
+ vdd_l7-supply = <&pm8916_s4>;
+
+ pm8916_s3: s3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pm8916_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ /* l1 is fixed to 1225000, but not connected in schematic */
+
+ pm8916_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8916_l4: l4 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ pm8916_l5: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l7: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l8: l8 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ pm8916_l9: l9 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l10: l10 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l11: l11 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8916_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8916_l13: l13 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ pm8916_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l16: l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ pm8916_l18: l18 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+};
+
+&sdhc_1 {
+ vmmc-supply = <&pm8916_l8>;
+ vqmmc-supply = <&pm8916_l5>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_default_state>;
+ pinctrl-1 = <&sdc1_sleep_state>;
+ status = "okay";
+};
+
+&sound {
+ model = "apq8039-square-sndcard";
+ audio-routing = "AMIC2", "MIC BIAS Internal2";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cdc_pdm_lines_default>;
+ pinctrl-1 = <&cdc_pdm_lines_sleep>;
+
+ internal-codec-playback-dai-link {
+ link-name = "WCD";
+ cpu {
+ sound-dai = <&lpass MI2S_PRIMARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
+ };
+ };
+
+ internal-codec-capture-dai-link {
+ link-name = "WCD-Capture";
+ cpu {
+ sound-dai = <&lpass MI2S_TERTIARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
+ };
+ };
+};
+
+&usb {
+ pinctrl-names = "default", "host", "device";
+ pinctrl-0 = <&pinctrl_otg_default>;
+ pinctrl-1 = <&pinctrl_otg_host>;
+ pinctrl-2 = <&pinctrl_otg_device>;
+ pin-switch-delay-us = <100000>;
+ usb-role-switch;
+ status = "okay";
+
+ ulpi {
+ usb_hs_phy: phy {
+ v1p8-supply = <&pm8916_l7>;
+ v3p3-supply = <&pm8916_l13>;
+ };
+ };
+ port {
+ otg_ep: endpoint {
+ remote-endpoint = <&typec_ep>;
+ };
+ };
+};
+
+&wcd_codec {
+ qcom,hphl-jack-type-normally-open;
+ qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+ qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+ status = "okay";
+};
--
2.38.1
next prev parent reply other threads:[~2023-01-17 2:53 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding Bryan O'Donoghue
2023-01-18 8:47 ` Stephan Gerhold
2023-01-18 12:05 ` Bryan O'Donoghue
2023-01-18 15:43 ` Stephan Gerhold
2023-01-19 0:32 ` Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 2/8] dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 3/8] dt-bindings: interconnect: Exclude all non msm8939 from snoc-mm Bryan O'Donoghue
2023-01-17 11:04 ` Krzysztof Kozlowski
2023-01-17 2:48 ` [PATCH v3 4/8] clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_* Bryan O'Donoghue
2023-01-18 13:49 ` Konrad Dybcio
2023-01-17 2:48 ` [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC Bryan O'Donoghue
2023-01-17 20:58 ` Bjorn Andersson
2023-01-17 22:48 ` Bryan O'Donoghue
2023-01-18 5:09 ` Bjorn Andersson
2023-01-20 0:40 ` Bryan O'Donoghue
2023-01-20 0:42 ` Bryan O'Donoghue
2023-01-20 0:45 ` Bryan O'Donoghue
2023-01-18 9:59 ` Stephan Gerhold
2023-01-18 11:50 ` Bryan O'Donoghue
2023-01-18 12:50 ` Bryan O'Donoghue
2023-01-18 17:33 ` Stephan Gerhold
2023-01-19 0:53 ` Bryan O'Donoghue
2023-01-21 22:57 ` Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 6/8] arm64: dts: qcom: Add msm8939-pm8916.dtsi include Bryan O'Donoghue
2023-01-18 13:49 ` Konrad Dybcio
2023-01-17 2:48 ` Bryan O'Donoghue [this message]
2023-01-17 21:06 ` [PATCH v3 7/8] arm64: dts: qcom: Add Square apq8039-t2 board Bjorn Andersson
2023-01-17 2:48 ` [PATCH v3 8/8] arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua Bryan O'Donoghue
2023-01-18 14:42 ` Konrad Dybcio
2023-01-18 15:11 ` Bryan O'Donoghue
2023-01-18 22:50 ` (subset) [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230117024846.1367794-8-bryan.odonoghue@linaro.org \
--to=bryan.odonoghue@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=benl@squareup.com \
--cc=devicetree@vger.kernel.org \
--cc=djakov@kernel.org \
--cc=dmitry.baryshkov@linaro.org \
--cc=fabien.parent@linaro.org \
--cc=jgates@squareup.com \
--cc=jun.nie@linaro.org \
--cc=jwillcox@squareup.com \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=leo.yan@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=mchen@squareup.com \
--cc=robh+dt@kernel.org \
--cc=shawn.guo@linaro.org \
--cc=zac@squareup.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).