From: rfoss@kernel.org
To: agross@kernel.org, andersson@kernel.org,
konrad.dybcio@linaro.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org, linux-arm-msm@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Robert Foss <robert.foss@linaro.org>
Subject: [PATCH v1 1/3] arm64: dts: qcom: sm8350: Add display system nodes
Date: Tue, 17 Jan 2023 13:02:21 +0100 [thread overview]
Message-ID: <20230117120223.1055225-2-rfoss@kernel.org> (raw)
In-Reply-To: <20230117120223.1055225-1-rfoss@kernel.org>
From: Robert Foss <robert.foss@linaro.org>
Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these
nodes the display subsystem is configured to support
one DSI output.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 297 ++++++++++++++++++++++++++-
1 file changed, 293 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index fafd92edc855..c78cdaa4adcb 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -3,6 +3,7 @@
* Copyright (c) 2020, Linaro Limited
*/
+#include <dt-bindings/interconnect/qcom,sm8350.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,dispcc-sm8350.h>
#include <dt-bindings/clock/qcom,gcc-sm8350.h>
@@ -2620,14 +2621,302 @@ usb_2_dwc3: usb@a800000 {
};
};
+ mdss: display-subsystem@ae00000 {
+ compatible = "qcom,sm8350-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+
+ interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
+ <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "mdp0-mem", "mdp1-mem";
+
+ power-domains = <&dispcc MDSS_GDSC>;
+ resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface", "bus", "nrt_bus", "core";
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ iommus = <&apps_smmu 0x820 0x402>;
+
+ status = "disabled";
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ dpu_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ /* TODO: opp-200000000 should work with
+ * &rpmhpd_opp_low_svs, but one some of
+ * sm8350_hdk boards reboot using this
+ * opp.
+ */
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-345000000 {
+ opp-hz = /bits/ 64 <345000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-460000000 {
+ opp-hz = /bits/ 64 <460000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
+ mdss_mdp: display-controller@ae01000 {
+ compatible = "qcom,sm8350-dpu";
+ reg = <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus",
+ "nrt_bus",
+ "iface",
+ "lut",
+ "core",
+ "vsync";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ operating-points-v2 = <&dpu_opp_table>;
+ power-domains = <&rpmhpd SM8350_MMCX>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+
+ mdss_dsi0: dsi@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae94000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi0_phy 0>,
+ <&mdss_dsi0_phy 1>;
+
+ operating-points-v2 = <&dsi0_opp_table>;
+ power-domains = <&rpmhpd SM8350_MMCX>;
+
+ phys = <&mdss_dsi0_phy>;
+
+ status = "disabled";
+
+ dsi0_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ /* TODO: opp-187500000 should work with
+ * &rpmhpd_opp_low_svs, but one some of
+ * sm8350_hdk boards reboot using this
+ * opp.
+ */
+ opp-187500000 {
+ opp-hz = /bits/ 64 <187500000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-358000000 {
+ opp-hz = /bits/ 64 <358000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ mdss_dsi0_phy: phy@ae94400 {
+ compatible = "qcom,dsi-phy-5nm-8350";
+ reg = <0 0x0ae94400 0 0x200>,
+ <0 0x0ae94600 0 0x280>,
+ <0 0x0ae94900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+
+ mdss_dsi1: dsi@ae96000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae96000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi1_phy 0>,
+ <&mdss_dsi1_phy 1>;
+
+ operating-points-v2 = <&dsi1_opp_table>;
+ power-domains = <&rpmhpd SM8350_MMCX>;
+
+ phys = <&mdss_dsi1_phy>;
+
+ status = "disabled";
+
+ dsi1_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ /* TODO: opp-187500000 should work with
+ * &rpmhpd_opp_low_svs, but one some of
+ * sm8350_hdk boards reboot using this
+ * opp.
+ */
+ opp-187500000 {
+ opp-hz = /bits/ 64 <187500000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-358000000 {
+ opp-hz = /bits/ 64 <358000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi1_in: endpoint {
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi1_out: endpoint {
+ };
+ };
+ };
+ };
+
+ mdss_dsi1_phy: phy@ae96400 {
+ compatible = "qcom,dsi-phy-5nm-8350";
+ reg = <0 0x0ae96400 0 0x200>,
+ <0 0x0ae96600 0 0x280>,
+ <0 0x0ae96900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+ };
+
dispcc: clock-controller@af00000 {
compatible = "qcom,sm8350-dispcc";
reg = <0 0x0af00000 0 0x10000>;
clocks = <&rpmhcc RPMH_CXO_CLK>,
- <0>,
- <0>,
- <0>,
- <0>,
+ <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>,
+ <0>, <0>,
<0>,
<0>;
clock-names = "bi_tcxo",
--
2.34.1
next prev parent reply other threads:[~2023-01-17 12:02 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-17 12:02 [PATCH v1 0/3] SM8350 Display DTS rfoss
2023-01-17 12:02 ` rfoss [this message]
2023-01-17 12:02 ` [PATCH v1 2/3] arm64: dts: qcom: sm8350-hdk: Enable display & dsi nodes rfoss
2023-01-17 12:03 ` Neil Armstrong
2023-01-17 12:02 ` [PATCH v1 3/3] arm64: dts: qcom: sm8350-hdk: Enable lt9611uxc dsi-hdmi bridge rfoss
2023-01-17 18:24 ` [PATCH v1 0/3] SM8350 Display DTS Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230117120223.1055225-2-rfoss@kernel.org \
--to=rfoss@kernel.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robert.foss@linaro.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).