From: Abel Vesa <abel.vesa@linaro.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
"vkoul@kernel.org" <vkoul@kernel.org>,
Kishon Vijay Abraham I <kishon@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: linux-arm-msm@vger.kernel.org, linux-phy@lists.infradead.org,
devicetree@vger.kernel.org,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Johan Hovold <johan@kernel.org>
Subject: [PATCH v4 3/6] phy: qcom-qmp: qserdes-txrx: Add v6 register offsets
Date: Tue, 17 Jan 2023 16:20:12 +0200 [thread overview]
Message-ID: <20230117142015.509675-4-abel.vesa@linaro.org> (raw)
In-Reply-To: <20230117142015.509675-1-abel.vesa@linaro.org>
The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new qserdes TX RX offsets in a dedicated
header file.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
.../qualcomm/phy-qcom-qmp-qserdes-txrx-v6.h | 77 +++++++++++++++++++
drivers/phy/qualcomm/phy-qcom-qmp.h | 1 +
2 files changed, 78 insertions(+)
create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6.h
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6.h
new file mode 100644
index 000000000000..a69233e68f9a
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_QSERDES_TXRX_USB_V6_H_
+#define QCOM_PHY_QMP_QSERDES_TXRX_USB_V6_H_
+
+#define QSERDES_V6_TX_CLKBUF_ENABLE 0x08
+#define QSERDES_V6_TX_RESET_TSYNC_EN 0x1c
+#define QSERDES_V6_TX_PRE_STALL_LDO_BOOST_EN 0x20
+#define QSERDES_V6_TX_TX_BAND 0x24
+#define QSERDES_V6_TX_INTERFACE_SELECT 0x2c
+#define QSERDES_V6_TX_RES_CODE_LANE_TX 0x34
+#define QSERDES_V6_TX_RES_CODE_LANE_RX 0x38
+#define QSERDES_V6_TX_RES_CODE_LANE_OFFSET_TX 0x3c
+#define QSERDES_V6_TX_RES_CODE_LANE_OFFSET_RX 0x40
+#define QSERDES_V6_TX_PARRATE_REC_DETECT_IDLE_EN 0x60
+#define QSERDES_V6_TX_BIST_PATTERN7 0x7c
+#define QSERDES_V6_TX_LANE_MODE_1 0x84
+#define QSERDES_V6_TX_LANE_MODE_3 0x8c
+#define QSERDES_V6_TX_LANE_MODE_4 0x90
+#define QSERDES_V6_TX_LANE_MODE_5 0x94
+#define QSERDES_V6_TX_RCV_DETECT_LVL_2 0xa4
+#define QSERDES_V6_TX_TRAN_DRVR_EMP_EN 0xc0
+#define QSERDES_V6_TX_TX_INTERFACE_MODE 0xc4
+#define QSERDES_V6_TX_VMODE_CTRL1 0xc8
+#define QSERDES_V6_TX_PI_QEC_CTRL 0xe4
+
+#define QSERDES_V6_RX_UCDR_FO_GAIN 0x08
+#define QSERDES_V6_RX_UCDR_SO_GAIN 0x14
+#define QSERDES_V6_RX_UCDR_FASTLOCK_FO_GAIN 0x30
+#define QSERDES_V6_RX_UCDR_SO_SATURATION_AND_ENABLE 0x34
+#define QSERDES_V6_RX_UCDR_FASTLOCK_COUNT_LOW 0x3c
+#define QSERDES_V6_RX_UCDR_FASTLOCK_COUNT_HIGH 0x40
+#define QSERDES_V6_RX_UCDR_PI_CONTROLS 0x44
+#define QSERDES_V6_RX_UCDR_SB2_THRESH1 0x4c
+#define QSERDES_V6_RX_UCDR_SB2_THRESH2 0x50
+#define QSERDES_V6_RX_UCDR_SB2_GAIN1 0x54
+#define QSERDES_V6_RX_UCDR_SB2_GAIN2 0x58
+#define QSERDES_V6_RX_AUX_DATA_TCOARSE_TFINE 0x60
+#define QSERDES_V6_RX_TX_ADAPT_POST_THRESH 0xcc
+#define QSERDES_V6_RX_VGA_CAL_CNTRL1 0xd4
+#define QSERDES_V6_RX_VGA_CAL_CNTRL2 0xd8
+#define QSERDES_V6_RX_GM_CAL 0xdc
+#define QSERDES_V6_RX_RX_EQU_ADAPTOR_CNTRL2 0xec
+#define QSERDES_V6_RX_RX_EQU_ADAPTOR_CNTRL3 0xf0
+#define QSERDES_V6_RX_RX_EQU_ADAPTOR_CNTRL4 0xf4
+#define QSERDES_V6_RX_RX_IDAC_TSETTLE_LOW 0xf8
+#define QSERDES_V6_RX_RX_IDAC_TSETTLE_HIGH 0xfc
+#define QSERDES_V6_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x110
+#define QSERDES_V6_RX_SIDGET_ENABLES 0x118
+#define QSERDES_V6_RX_SIGDET_CNTRL 0x11c
+#define QSERDES_V6_RX_SIGDET_DEGLITCH_CNTRL 0x124
+#define QSERDES_V6_RX_RX_MODE_00_LOW 0x15c
+#define QSERDES_V6_RX_RX_MODE_00_HIGH 0x160
+#define QSERDES_V6_RX_RX_MODE_00_HIGH2 0x164
+#define QSERDES_V6_RX_RX_MODE_00_HIGH3 0x168
+#define QSERDES_V6_RX_RX_MODE_00_HIGH4 0x16c
+#define QSERDES_V6_RX_RX_MODE_01_LOW 0x170
+#define QSERDES_V6_RX_RX_MODE_01_HIGH 0x174
+#define QSERDES_V6_RX_RX_MODE_01_HIGH2 0x178
+#define QSERDES_V6_RX_RX_MODE_01_HIGH3 0x17c
+#define QSERDES_V6_RX_RX_MODE_01_HIGH4 0x180
+#define QSERDES_V6_RX_RX_MODE_10_LOW 0x184
+#define QSERDES_V6_RX_RX_MODE_10_HIGH 0x188
+#define QSERDES_V6_RX_RX_MODE_10_HIGH2 0x18c
+#define QSERDES_V6_RX_RX_MODE_10_HIGH3 0x190
+#define QSERDES_V6_RX_RX_MODE_10_HIGH4 0x194
+#define QSERDES_V6_RX_DFE_EN_TIMER 0x1a0
+#define QSERDES_V6_RX_DFE_CTLE_POST_CAL_OFFSET 0x1a4
+#define QSERDES_V6_RX_DCC_CTRL1 0x1a8
+#define QSERDES_V6_RX_VTH_CODE 0x1b0
+#define QSERDES_V6_RX_SIGDET_CAL_CTRL1 0x1e4
+#define QSERDES_V6_RX_SIGDET_CAL_TRIM 0x1f8
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index d1275d20a3a3..a63a691b8372 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -22,6 +22,7 @@
#include "phy-qcom-qmp-qserdes-txrx-v5_5nm.h"
#include "phy-qcom-qmp-qserdes-com-v6.h"
+#include "phy-qcom-qmp-qserdes-txrx-v6.h"
#include "phy-qcom-qmp-qserdes-pll.h"
--
2.34.1
next prev parent reply other threads:[~2023-01-17 14:20 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-17 14:20 [PATCH v4 0/6] phy: qualcomm: Add UFS support for SM8550 Abel Vesa
2023-01-17 14:20 ` [PATCH v4 1/6] dt-bindings: phy: Add QMP UFS PHY comptible " Abel Vesa
2023-01-23 9:48 ` Johan Hovold
2023-01-17 14:20 ` [PATCH v4 2/6] phy: qcom-qmp: qserdes-com: Add v6 register offsets Abel Vesa
2023-01-17 14:28 ` Dmitry Baryshkov
2023-01-17 14:20 ` Abel Vesa [this message]
2023-01-17 14:20 ` [PATCH v4 4/6] phy: qcom-qmp: qserdes-txrx-ufs: " Abel Vesa
2023-01-17 14:42 ` Dmitry Baryshkov
2023-01-23 10:56 ` Abel Vesa
2023-01-17 14:20 ` [PATCH v4 5/6] phy: qcom-qmp: pcs-ufs: " Abel Vesa
2023-01-17 14:29 ` Dmitry Baryshkov
2023-01-17 14:20 ` [PATCH v4 6/6] phy: qcom-qmp-ufs: Add SM8550 support Abel Vesa
2023-01-17 14:47 ` Dmitry Baryshkov
2023-01-23 9:49 ` Johan Hovold
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230117142015.509675-4-abel.vesa@linaro.org \
--to=abel.vesa@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=johan@kernel.org \
--cc=kishon@kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).