From: Marco Felsch <m.felsch@pengutronix.de>
To: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Cc: Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Shawn Guo <shawnguo@kernel.org>,
Sascha Hauer <s.hauer@pengutronix.de>,
Fabio Estevam <festevam@gmail.com>, Li Yang <leoyang.li@nxp.com>,
Shengjiu Wang <shengjiu.wang@nxp.com>,
Richard Zhu <hongxing.zhu@nxp.com>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
NXP Linux Team <linux-imx@nxp.com>,
Pengutronix Kernel Team <kernel@pengutronix.de>
Subject: Re: [PATCH v7 1/3] arm64: dts: imx8mm-evk: move PMIC configuration
Date: Thu, 19 Jan 2023 10:51:13 +0100 [thread overview]
Message-ID: <20230119095112.mpo56lf4nd3udtht@pengutronix.de> (raw)
In-Reply-To: <20230110152316.1149940-2-johannes.schneider@leica-geosystems.com>
Hi Johannes,
thanks for your patch.
On 23-01-10, Johannes Schneider wrote:
> Move the PMIC configuration out of imx8mm-evk.dtsi into a separate
> file; to accommodate devicetrees for the rev-b EVK, which comes with a
I'm not sure if we should call it rev-b since this is quite confusing.
The whole EVK bundle (cpu-board + baseboard) is called EVKB. The most
recent cpu board revision is A4 and the the cpu board itself is called
8MMINILPD4-CPU2 whereas the older cpu board is called 8MMINILPD4-CPU.
So dts file name imx8mm-evkb is correct, but mention it as rev-b in your
commit message is wrong in my opinion.
> different PMIC.
>
> Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
> ---
> .../boot/dts/freescale/imx8mm-ddr4-evk.dts | 1 +
> .../dts/freescale/imx8mm-evk-rohm-pmic.dtsi | 118 ++++++++++++++++++
> arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 1 +
> arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi | 112 -----------------
> 4 files changed, 120 insertions(+), 112 deletions(-)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-evk-rohm-pmic.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-ddr4-evk.dts
> index 6c079c0a3a48..f39182ce65b4 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-ddr4-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-ddr4-evk.dts
> @@ -6,6 +6,7 @@
> /dts-v1/;
>
> #include "imx8mm-evk.dtsi"
> +#include "imx8mm-evk-rohm-pmic.dtsi"
Do we really need to move it into another dtsi file? I would either
suggest to move the pmic description into the .dts file since it is not
common anymore. This way we can avoid the imx8mm-evk-rohm-pmic.dtsi.
Regards,
Marco
> / {
> model = "FSL i.MX8MM DDR4 EVK with CYW43455 WIFI/BT board";
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk-rohm-pmic.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk-rohm-pmic.dtsi
> new file mode 100644
> index 000000000000..0b056996a27b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk-rohm-pmic.dtsi
> @@ -0,0 +1,118 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 NXP
> + */
> +
> +&i2c1 {
> + pmic@4b {
> + compatible = "rohm,bd71847";
> + reg = <0x4b>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pmic>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> + rohm,reset-snvs-powered;
> +
> + #clock-cells = <0>;
> + clocks = <&osc_32k 0>;
> + clock-output-names = "clk-32k-out";
> +
> + regulators {
> + buck1_reg: BUCK1 {
> + regulator-name = "buck1";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <1250>;
> + };
> +
> + buck2_reg: BUCK2 {
> + regulator-name = "buck2";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <1250>;
> + rohm,dvs-run-voltage = <1000000>;
> + rohm,dvs-idle-voltage = <900000>;
> + };
> +
> + buck3_reg: BUCK3 {
> + // BUCK5 in datasheet
> + regulator-name = "buck3";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck4_reg: BUCK4 {
> + // BUCK6 in datasheet
> + regulator-name = "buck4";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck5_reg: BUCK5 {
> + // BUCK7 in datasheet
> + regulator-name = "buck5";
> + regulator-min-microvolt = <1605000>;
> + regulator-max-microvolt = <1995000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck6_reg: BUCK6 {
> + // BUCK8 in datasheet
> + regulator-name = "buck6";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo1_reg: LDO1 {
> + regulator-name = "ldo1";
> + regulator-min-microvolt = <1600000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2_reg: LDO2 {
> + regulator-name = "ldo2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <900000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3_reg: LDO3 {
> + regulator-name = "ldo3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo4_reg: LDO4 {
> + regulator-name = "ldo4";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo6_reg: LDO6 {
> + regulator-name = "ldo6";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> index a2b24d4d4e3e..d2b6d7de7e53 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> @@ -7,6 +7,7 @@
>
> #include <dt-bindings/usb/pd.h>
> #include "imx8mm-evk.dtsi"
> +#include "imx8mm-evk-rohm-pmic.dtsi"
>
> / {
> model = "FSL i.MX8MM EVK board";
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> index 7d6317d95b13..21d0614af44c 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> @@ -182,118 +182,6 @@ &i2c1 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_i2c1>;
> status = "okay";
> -
> - pmic@4b {
> - compatible = "rohm,bd71847";
> - reg = <0x4b>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_pmic>;
> - interrupt-parent = <&gpio1>;
> - interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> - rohm,reset-snvs-powered;
> -
> - #clock-cells = <0>;
> - clocks = <&osc_32k 0>;
> - clock-output-names = "clk-32k-out";
> -
> - regulators {
> - buck1_reg: BUCK1 {
> - regulator-name = "buck1";
> - regulator-min-microvolt = <700000>;
> - regulator-max-microvolt = <1300000>;
> - regulator-boot-on;
> - regulator-always-on;
> - regulator-ramp-delay = <1250>;
> - };
> -
> - buck2_reg: BUCK2 {
> - regulator-name = "buck2";
> - regulator-min-microvolt = <700000>;
> - regulator-max-microvolt = <1300000>;
> - regulator-boot-on;
> - regulator-always-on;
> - regulator-ramp-delay = <1250>;
> - rohm,dvs-run-voltage = <1000000>;
> - rohm,dvs-idle-voltage = <900000>;
> - };
> -
> - buck3_reg: BUCK3 {
> - // BUCK5 in datasheet
> - regulator-name = "buck3";
> - regulator-min-microvolt = <700000>;
> - regulator-max-microvolt = <1350000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - buck4_reg: BUCK4 {
> - // BUCK6 in datasheet
> - regulator-name = "buck4";
> - regulator-min-microvolt = <3000000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - buck5_reg: BUCK5 {
> - // BUCK7 in datasheet
> - regulator-name = "buck5";
> - regulator-min-microvolt = <1605000>;
> - regulator-max-microvolt = <1995000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - buck6_reg: BUCK6 {
> - // BUCK8 in datasheet
> - regulator-name = "buck6";
> - regulator-min-microvolt = <800000>;
> - regulator-max-microvolt = <1400000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - ldo1_reg: LDO1 {
> - regulator-name = "ldo1";
> - regulator-min-microvolt = <1600000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - ldo2_reg: LDO2 {
> - regulator-name = "ldo2";
> - regulator-min-microvolt = <800000>;
> - regulator-max-microvolt = <900000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - ldo3_reg: LDO3 {
> - regulator-name = "ldo3";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - ldo4_reg: LDO4 {
> - regulator-name = "ldo4";
> - regulator-min-microvolt = <900000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - ldo6_reg: LDO6 {
> - regulator-name = "ldo6";
> - regulator-min-microvolt = <900000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> - };
> - };
> };
>
> &i2c2 {
> --
> 2.25.1
>
>
>
next prev parent reply other threads:[~2023-01-19 9:51 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-10 15:23 [PATCH v7 0/3] pmic on imx8mm Johannes Schneider
2023-01-10 15:23 ` [PATCH v7 1/3] arm64: dts: imx8mm-evk: move PMIC configuration Johannes Schneider
2023-01-19 9:51 ` Marco Felsch [this message]
2023-01-19 10:02 ` Ahmad Fatoum
2023-01-19 10:45 ` Marco Felsch
2023-01-10 15:23 ` [PATCH v7 2/3] arm64: dts: imx8mm-evk: add revision-B EVK Johannes Schneider
2023-01-20 19:53 ` Marco Felsch
2023-01-21 19:51 ` Krzysztof Kozlowski
2023-01-10 15:23 ` [PATCH v7 3/3] dt-bindings: arm: fsl: Add i.MX8MM-EVK rev-b Johannes Schneider
2023-01-20 19:50 ` Marco Felsch
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230119095112.mpo56lf4nd3udtht@pengutronix.de \
--to=m.felsch@pengutronix.de \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=hongxing.zhu@nxp.com \
--cc=johannes.schneider@leica-geosystems.com \
--cc=kernel@pengutronix.de \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
--cc=shengjiu.wang@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).