From: Chanh Nguyen <chanh@os.amperecomputing.com>
To: OpenBMC Maillist <openbmc@lists.ozlabs.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Joel Stanley <joel@jms.id.au>, Andrew Jeffery <andrew@aj.id.au>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-aspeed@lists.ozlabs.org, linux-kernel@vger.kernel.org
Cc: Chanh Nguyen <chanh@os.amperecomputing.com>
Subject: [PATCH] ARM: dts: aspeed: mtmitchell: Enable NCSI
Date: Fri, 17 Feb 2023 17:21:22 +0700 [thread overview]
Message-ID: <20230217102122.16547-1-chanh@os.amperecomputing.com> (raw)
Support the mac3 (RGMII4) as an NC-SI stack instead of an MDIO PHY.
The OCP slot #0 and OCP slot #1 use a common the BMC_NCSI signal,
so we use only one of them at the same time. The OCP slot #0 will
be enabled by PCA9539's setting by default.
Also, enable the OCP Auxiliary Power during booting.
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
---
.../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 37 ++++++++++++++++++-
1 file changed, 36 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
index 4b91600eaf62..e8a6b1f08d6a 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
@@ -251,6 +251,14 @@
pinctrl-0 = <&pinctrl_rgmii1_default>;
};
+&mac3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii4_default>;
+ clock-names = "MACCLK", "RCLK";
+ use-ncsi;
+};
+
&fmc {
status = "okay";
flash@0 {
@@ -439,6 +447,26 @@
status = "okay";
};
+&i2c8 {
+ status = "okay";
+
+ pca9539@77 {
+ compatible = "nxp,pca9539";
+ reg = <0x77>;
+ gpio-controller;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #gpio-cells = <2>;
+
+ bmc-ocp0-en-hog {
+ gpio-hog;
+ gpios = <7 GPIO_ACTIVE_LOW>;
+ output-high;
+ line-name = "bmc-ocp0-en-n";
+ };
+ };
+};
+
&i2c9 {
status = "okay";
};
@@ -530,13 +558,20 @@
/*V0-V7*/ "s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
"host0-reboot-ack-n","host0-ready","host0-shd-req-n",
"host0-shd-ack-n","s0-overtemp-n",
- /*W0-W7*/ "ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
+ /*W0-W7*/ "","ocp-main-pwren","ocp-pgood","",
"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
/*X0-X7*/ "i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
"s1-overtemp-n","s1-spi-auth-fail-n",
/*Y0-Y7*/ "","","","","","","","host0-special-boot",
/*Z0-Z7*/ "reset-button","ps0-pgood","ps1-pgood","","","","","";
+
+ ocp-aux-pwren-hog {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "ocp-aux-pwren";
+ };
};
&gpio1 {
--
2.17.1
next reply other threads:[~2023-02-17 10:21 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-02-17 10:21 Chanh Nguyen [this message]
2023-02-17 11:32 ` [PATCH] ARM: dts: aspeed: mtmitchell: Enable NCSI Krzysztof Kozlowski
2023-02-21 7:29 ` Chanh Nguyen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230217102122.16547-1-chanh@os.amperecomputing.com \
--to=chanh@os.amperecomputing.com \
--cc=andrew@aj.id.au \
--cc=devicetree@vger.kernel.org \
--cc=joel@jms.id.au \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-kernel@vger.kernel.org \
--cc=openbmc@lists.ozlabs.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).