From: Konrad Dybcio <konrad.dybcio@linaro.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Marijn Suijten <marijn.suijten@somainline.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Konrad Dybcio <konrad.dybcio@linaro.org>
Subject: [PATCH v2 2/4] arm64: dts: qcom: sm8150-kumano: Add GPIO line names for TLMM
Date: Tue, 11 Apr 2023 20:14:42 +0200 [thread overview]
Message-ID: <20230315-topic-kumano_dts0-v2-2-0ca7fa521b86@linaro.org> (raw)
In-Reply-To: <20230315-topic-kumano_dts0-v2-0-0ca7fa521b86@linaro.org>
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the common DTSI to better document the hardware.
The pin assignment for TLMM is identical on both devices. Great job!
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
.../boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi | 175 +++++++++++++++++++++
1 file changed, 175 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi b/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
index 6753c65d75bc..d1a3ab836019 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
@@ -541,6 +541,181 @@ &qupv3_id_1 {
&tlmm {
gpio-reserved-ranges = <126 4>;
+ gpio-line-names = "NFC_ESE_SPI_MISO", /* GPIO_0 */
+ "NFC_ESE_SPI_MOSI",
+ "NFC_ESE_SPI_SCLK",
+ "NFC_ESE_SPI_CS_N",
+ "NC",
+ "NC",
+ "DISP_RESET_N",
+ "DEBUG_GPIO0",
+ "MDP_VSYNC_P",
+ "TS_I2C_SDA",
+ "TS_I2C_SCL", /* GPIO_10 */
+ "CAM_SOF",
+ "CAM2_RST_N",
+ "CAM_MCLK0",
+ "CAM_MCLK1",
+ "CAM_MCLK2",
+ "CAM_MCLK3",
+ "CCI_I2C_SDA0",
+ "CCI_I2C_SCL0",
+ "CCI_I2C_SDA1",
+ "CCI_I2C_SCL1", /* GPIO_20 */
+ "NC",
+ "MAIN_CAM_PWR_EN",
+ "CAM3_RST_N",
+ "NC",
+ "CHAT_CAM_PWR_EN",
+ "NC",
+ "NC",
+ "CAM0_RST_N",
+ "RGBC_IR_PWR_EN",
+ "CAM1_RST_N", /* GPIO_30 */
+ "CCI_I2C_SDA2",
+ "CCI_I2C_SCL2",
+ "CCI_I2C_SDA3",
+ "CCI_I2C_SCL3",
+ "NC",
+ "DEBUG_GPIO1",
+ "RGBC_IR_INT",
+ "USB_CC_DIR",
+ "NC",
+ "NC", /* GPIO_40 */
+ "NFC_EN",
+ "NFC_ESE_PWR_REQ",
+ "BT_HCI_UART_CTS_N",
+ "BT_HCI_UART_RFR_N",
+ "BT_HCI_UART_TXD",
+ "BT_HCI_UART_RXD",
+ "NFC_IRQ",
+ "NFC_DWL_REQ",
+ "UIM2_DETECT_EN",
+ "WLAN_SW_CTRL", /* GPIO_50 */
+ "APPS_I2C_SDA",
+ "APPS_I2C_SCL",
+ "NC",
+ "TS_RESET_N",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "HW_ID_0",
+ "NC", /* GPIO_60 */
+ "QLINK_REQUEST",
+ "QLINK_ENABLE",
+ "WMSS_RESET_N",
+ "SDM_GRFC_8",
+ "WDOG_DISABLE",
+ "NC",
+ "NC",
+ "PA_INDICATOR_OR",
+ "MSS_LTE_COXM_TXD",
+ "MSS_LTE_COXM_RXD", /* GPIO_70 */
+ "SDM_RFFE0_DATA",
+ "SDM_RFFE0_CLK",
+ "SDM_RFFE1_DATA",
+ "SDM_RFFE1_CLK",
+ "SDM_RFFE2_DATA",
+ "SDM_RFFE2_CLK",
+ "SDM_RFFE3_DATA",
+ "SDM_RFFE3_CLK",
+ "SUB_CAM_PWR_EN",
+ "FP_RESET_N", /* GPIO_80 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "DEBUG_UART_TX",
+ "DEBUG_UART_RX",
+ "DVDT_WRT_DET_AND",
+ "NC",
+ "NC",
+ "NC", /* GPIO_90 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "UDON_SWITCH_SEL",
+ "SD_CARD_DET_N",
+ "NC",
+ "CAMSENSOR_I2C_SDA",
+ "CAMSENSOR_I2C_SCL",
+ "USB_AUDIO_EN1", /* GPIO_100 */
+ "DISP_ERR_FG",
+ "NC",
+ "NC",
+ "NC",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RESET",
+ "UIM2_DET",
+ "UIM1_DATA",
+ "UIM1_CLK", /* GPIO_110 */
+ "UIM1_RESET",
+ "UIM1_PRESENT",
+ "NFC_CLK_REQ",
+ "SW_SERVICE",
+ "NC",
+ "RF_ID_EXTENSION",
+ "ALS_PROX_INT_N",
+ "FP_INT",
+ "DVDT_WRT_DET_OR",
+ "BAROMETER_INT", /* GPIO_120 */
+ "ACC_COVER_OPEN",
+ "TS_INT_N",
+ "CODEC_INT1_N",
+ "CODEC_INT2_N",
+ "TX_GTR_THRES_IN",
+ "FP_SPI_MISO",
+ "FP_SPI_MOSI",
+ "FP_SPI_SCLK",
+ "FP_SPI_CS_N",
+ "NC", /* GPIO_130 */
+ "DVDT_ENABLE",
+ "ACCEL_INT",
+ "NC",
+ "MAG_INT_N",
+ "NC",
+ "FORCED_USB_BOOT",
+ "NC",
+ "NC",
+ "HW_ID_1",
+ "NC", /* GPIO_140 */
+ "NC",
+ "NC",
+ "CODEC_RST_N",
+ "CDC_SPI_MISO",
+ "CDC_SPI_MOSI",
+ "CDC_SPI_SCLK",
+ "CDC_SPI_CS_N",
+ "NC",
+ "LPASS_SLIMBUS_CLK",
+ "LPASS_SLIMBUS_DATA0", /* GPIO_150 */
+ "LPASS_SLIMBUS_DATA1",
+ "USB_AUDIO_EN2",
+ "BT_FM_SLIMBUS_DATA",
+ "BT_FM_SLIMBUS_CLK",
+ "COMPASS_I2C_SDA",
+ "COMPASS_I2C_SCL",
+ "SSC_SPI_1_MISO",
+ "SSC_SPI_1_MOSI",
+ "SSC_SPI_1_CLK",
+ "SSC_SPI_1_CS_N", /* GPIO_160 */
+ "SSC_SENSOR_I2C_SDA",
+ "SSC_SENSOR_I2C_SCL",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "SSC_UART_1_TX",
+ "SSC_UART_1_RX",
+ "WL_CMD_CLK_CHAIN0",
+ "WL_CMD_DATA_CHAIN0", /* GPIO_170 */
+ "WL_CMD_CLK_CHAIN1",
+ "WL_CMD_DATA_CHAIN1",
+ "WL_BT_COEX_CLK",
+ "WL_BT_COEX_DATA";
};
&uart2 {
--
2.40.0
next prev parent reply other threads:[~2023-04-11 18:14 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-04-11 18:14 [PATCH v2 0/4] SM8150 Kumano updates Konrad Dybcio
2023-04-11 18:14 ` [PATCH v2 1/4] arm64: dts: qcom: sm8150-kumano: Add GPIO line names for PMIC GPIOs Konrad Dybcio
2023-04-11 18:14 ` Konrad Dybcio [this message]
2023-04-11 18:14 ` [PATCH v2 3/4] arm64: dts: qcom: sm8150-kumano: Set up camera fixed regulators Konrad Dybcio
2023-04-11 18:14 ` [PATCH v2 4/4] arm64: dts: qcom: sm8150-kumano: Enable SDHCI2 Konrad Dybcio
2023-04-14 7:29 ` Marijn Suijten
2023-05-25 4:54 ` [PATCH v2 0/4] SM8150 Kumano updates Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230315-topic-kumano_dts0-v2-2-0ca7fa521b86@linaro.org \
--to=konrad.dybcio@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marijn.suijten@somainline.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).