From: Konrad Dybcio <konrad.dybcio@linaro.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Robert Marko <robimarko@gmail.com>,
Das Srinagesh <quic_gurus@quicinc.com>
Cc: Bhupesh Sharma <bhupesh.sharma@linaro.org>,
Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>,
Marijn Suijten <marijn.suijten@somainline.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Konrad Dybcio <konrad.dybcio@linaro.org>
Subject: [PATCH 4/9] arm64: dts: qcom: qcm2290: Add most QUPs
Date: Mon, 03 Apr 2023 19:36:02 +0200 [thread overview]
Message-ID: <20230403-topic-rb1_qcm-v1-4-ca849b62ba07@linaro.org> (raw)
In-Reply-To: <20230403-topic-rb1_qcm-v1-0-ca849b62ba07@linaro.org>
Add all I2C and SPI hosts, the debug UART port and the related pinctrl.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
arch/arm64/boot/dts/qcom/qcm2290.dtsi | 294 ++++++++++++++++++++++++++++++++++
1 file changed, 294 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
index 27d4742cdb19..edfa18190454 100644
--- a/arch/arm64/boot/dts/qcom/qcm2290.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
@@ -310,6 +310,90 @@ tlmm: pinctrl@500000 {
interrupt-controller;
#interrupt-cells = <2>;
+ qup_i2c0_default: qup-i2c0-default-state {
+ pins = "gpio0", "gpio1";
+ function = "qup0";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c1_default: qup-i2c1-default-state {
+ pins = "gpio4", "gpio5";
+ function = "qup1";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c2_default: qup-i2c2-default-state {
+ pins = "gpio6", "gpio7";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c3_default: qup-i2c3-default-state {
+ pins = "gpio8", "gpio9";
+ function = "qup3";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c4_default: qup-i2c4-default-state {
+ pins = "gpio12", "gpio13";
+ function = "qup4";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c5_default: qup-i2c5-default-state {
+ pins = "gpio14", "gpio15";
+ function = "qup5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi0_default: qup-spi0-default-state {
+ pins = "gpio0", "gpio1","gpio2", "gpio3";
+ function = "qup0";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi1_default: qup-spi1-default-state {
+ pins = "gpio4", "gpio5", "gpio69", "gpio70";
+ function = "qup1";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi2_default: qup-spi2-default-state {
+ pins = "gpio6", "gpio7", "gpio71", "gpio80";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi3_default: qup-spi3-default-state {
+ pins = "gpio8", "gpio9", "gpio10", "gpio11";
+ function = "qup3";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi4_default: qup-spi4-default-state {
+ pins = "gpio12", "gpio13", "gpio96", "gpio97";
+ function = "qup4";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi5_default: qup-spi5-default-state {
+ pins = "gpio14", "gpio15", "gpio16", "gpio17";
+ function = "qup5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
qup_uart0_default: qup-uart0-default-state {
pins = "gpio0", "gpio1", "gpio2", "gpio3";
function = "qup0";
@@ -317,6 +401,13 @@ qup_uart0_default: qup-uart0-default-state {
bias-disable;
};
+ qup_uart4_default: qup-uart4-default-state {
+ pins = "gpio12", "gpio13";
+ function = "qup4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
sdc1_state_on: sdc1-on-state {
clk-pins {
pins = "sdc1_clk";
@@ -604,6 +695,38 @@ qupv3_id_0: geniqup@4ac0000 {
ranges;
status = "disabled";
+ i2c0: i2c@4a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a80000 0x0 0x4000>;
+ interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c0_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi0: spi@4a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a80000 0x0 0x4000>;
+ interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi0_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
uart0: serial@4a80000 {
compatible = "qcom,geni-uart";
reg = <0x0 0x04a80000 0x0 0x4000>;
@@ -614,6 +737,177 @@ uart0: serial@4a80000 {
pinctrl-names = "default";
status = "disabled";
};
+
+ i2c1: i2c@4a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a84000 0x0 0x4000>;
+ interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c1_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi1: spi@4a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a84000 0x0 0x4000>;
+ interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi1_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@4a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a88000 0x0 0x4000>;
+ interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c2_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi2: spi@4a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a88000 0x0 0x4000>;
+ interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi2_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@4a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a8c000 0x0 0x4000>;
+ interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c3_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi3: spi@4a8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a8c000 0x0 0x4000>;
+ interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi3_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@4a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a90000 0x0 0x4000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c4_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi4: spi@4a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a90000 0x0 0x4000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi4_default>;
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart4: serial@4a90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x04a90000 0x0 0x4000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart4_default>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ i2c5: i2c@4a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a94000 0x0 0x4000>;
+ interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c5_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi5: spi@4a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a94000 0x0 0x4000>;
+ interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi5_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};
usb: usb@4ef8800 {
--
2.40.0
next prev parent reply other threads:[~2023-04-03 17:36 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-04-03 17:35 [PATCH 0/9] RB1 + QCM2290 support Konrad Dybcio
2023-04-03 17:35 ` [PATCH 1/9] dt-bindings: firmware: document Qualcomm QCM2290 SCM Konrad Dybcio
2023-04-04 6:02 ` Krzysztof Kozlowski
2023-04-03 17:36 ` [PATCH 2/9] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board Konrad Dybcio
2023-04-04 6:03 ` Krzysztof Kozlowski
2023-04-03 17:36 ` [PATCH 3/9] arm64: dts: qcom: Add initial QCM2290, PM2250 & RB1 device trees Konrad Dybcio
2023-04-04 6:06 ` Krzysztof Kozlowski
2023-04-04 9:47 ` Konrad Dybcio
2023-04-04 10:02 ` Krzysztof Kozlowski
2023-04-03 17:36 ` Konrad Dybcio [this message]
2023-04-03 17:36 ` [PATCH 5/9] arm64: dts: qcom: qcm2290: Add thermal zones Konrad Dybcio
2023-04-03 17:36 ` [PATCH 6/9] arm64: dts: qcom: qcm2290: Add SMP2P Konrad Dybcio
2023-04-03 17:36 ` [PATCH 7/9] arm64: dts: qcom: qcm2290: Add ADSP & modem Konrad Dybcio
2023-04-03 17:36 ` [PATCH 8/9] arm64: dts: qcom: qcm2290: Add WCN3990 Wi-Fi node Konrad Dybcio
2023-04-04 6:08 ` Krzysztof Kozlowski
2023-04-04 9:55 ` Konrad Dybcio
2023-04-04 10:04 ` Krzysztof Kozlowski
2023-04-04 10:05 ` Krzysztof Kozlowski
2023-04-03 17:36 ` [PATCH 9/9] arm64: dts: qcom: qrb2210-rb1: Enable RESIN Volume Down Konrad Dybcio
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230403-topic-rb1_qcm-v1-4-ca849b62ba07@linaro.org \
--to=konrad.dybcio@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=bhupesh.sharma@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marijn.suijten@somainline.org \
--cc=quic_gurus@quicinc.com \
--cc=robh+dt@kernel.org \
--cc=robimarko@gmail.com \
--cc=vladimir.zapolskiy@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).