From: Steffen Trumtrar <s.trumtrar@pengutronix.de>
To: linux-stm32@st-md-mailman.stormreply.com
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@foss.st.com>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: [PATCH v9 05/10] ARM: dts: stm32: Add pinmux for USART1 pins
Date: Fri, 5 May 2023 08:01:53 +0200 [thread overview]
Message-ID: <20230505060158.16516-6-s.trumtrar@pengutronix.de> (raw)
In-Reply-To: <20230505060158.16516-1-s.trumtrar@pengutronix.de>
Add a mux option for the USART1 pins.
This is used on the Phycore STM32MP1.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 57 ++++++++++++++++++++++++
1 file changed, 57 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 74d01a88e1f7..c8490e5bea16 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -2258,6 +2258,33 @@ pins {
};
};
+ usart1_pins_a: usart1-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('A', 12, AF7)>; /* USART1_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('A', 11, AF7)>; /* USART1_CTS_NSS */
+ bias-disable;
+ };
+ };
+
+ usart1_idle_pins_a: usart1-idle-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('A', 12, ANALOG)>, /* USART1_RTS */
+ <STM32_PINMUX('A', 11, AF7)>; /* USART1_CTS_NSS */
+ };
+ };
+
+ usart1_sleep_pins_a: usart1-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 12, ANALOG)>, /* USART1_RTS */
+ <STM32_PINMUX('A', 11, ANALOG)>; /* USART1_CTS_NSS */
+ };
+ };
+
usart2_pins_a: usart2-0 {
pins1 {
pinmux = <STM32_PINMUX('F', 5, AF7)>, /* USART2_TX */
@@ -2612,4 +2639,34 @@ pins2 {
bias-disable;
};
};
+
+ usart1_idle_pins_b: usart1-idle-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('Z', 7, ANALOG)>; /* USART1_TX */
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('Z', 6, AF7)>; /* USART1_RX */
+ bias-disable;
+ };
+ };
+
+ usart1_sleep_pins_b: usart1-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('Z', 7, ANALOG)>, /* USART1_TX */
+ <STM32_PINMUX('Z', 6, ANALOG)>; /* USART1_RX */
+ };
+ };
+
+ usart1_pins_b: usart1-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('Z', 7, AF7)>; /* USART1_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('Z', 6, AF7)>; /* USART1_RX */
+ bias-disable;
+ };
+ };
};
--
2.39.1
next prev parent reply other threads:[~2023-05-05 6:02 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-05-05 6:01 [PATCH v9 00/10] ARM: stm32: add support for Phycore STM32MP1 Steffen Trumtrar
2023-05-05 6:01 ` [PATCH v9 01/10] ARM: dts: stm32: Add alternate pinmux for ethernet Steffen Trumtrar
2023-05-05 6:01 ` [PATCH v9 02/10] ARM: dts: stm32: Add alternate pinmux for sai2b Steffen Trumtrar
2023-05-05 6:01 ` [PATCH v9 03/10] ARM: dts: stm32: Add new pinmux for sdmmc1_b4 Steffen Trumtrar
2023-05-05 6:01 ` [PATCH v9 04/10] ARM: dts: stm32: Add new pinmux for sdmmc2_d47 Steffen Trumtrar
2023-05-05 6:01 ` Steffen Trumtrar [this message]
2023-05-05 6:01 ` [PATCH v9 06/10] ARM: dts: stm32: Add idle/sleep pinmux for USART3 Steffen Trumtrar
2023-05-05 6:01 ` [PATCH v9 07/10] ARM: dts: stm32: Add sleep pinmux for SPI1 pins_a Steffen Trumtrar
2023-05-05 6:01 ` [PATCH v9 08/10] dt-bindings: arm: stm32: Add Phytec STM32MP1 board Steffen Trumtrar
2023-05-05 6:01 ` [PATCH v9 09/10] ARM: dts: stm32: add STM32MP1-based Phytec SoM Steffen Trumtrar
2023-05-05 6:01 ` [PATCH v9 10/10] ARM: dts: stm32: add STM32MP1-based Phytec board Steffen Trumtrar
2023-05-23 14:58 ` Christophe Parant
2023-06-23 8:59 ` Christophe Parant
2023-06-23 10:39 ` Alexandre TORGUE
2023-05-16 15:16 ` [PATCH v9 00/10] ARM: stm32: add support for Phycore STM32MP1 Alexandre TORGUE
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230505060158.16516-6-s.trumtrar@pengutronix.de \
--to=s.trumtrar@pengutronix.de \
--cc=alexandre.torgue@foss.st.com \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mcoquelin.stm32@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).