From: Yangtao Li <frank.li@vivo.com>
To: Jisheng Zhang <jszhang@kernel.org>, Wei Fu <wefu@redhat.com>,
Yangtao Li <frank.li@vivo.com>, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
Albert Ou <aou@eecs.berkeley.edu>
Cc: Icenowy Zheng <uwu@icenowy.me>,
linux-riscv@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v2 2/5] riscv: dts: add initial T-HEAD light SoC device tree
Date: Thu, 11 May 2023 04:44:53 +0800 [thread overview]
Message-ID: <20230510204456.57202-2-frank.li@vivo.com> (raw)
In-Reply-To: <20230510204456.57202-1-frank.li@vivo.com>
From: Jisheng Zhang <jszhang@kernel.org>
Add initial device tree for the TH1520 RISC-V SoC by
T-HEAD.
Cc: Icenowy Zheng <uwu@icenowy.me>
Cc: Wei Fu <wefu@redhat.com>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
---
v2:
-remove reset-sample
-convert to use thead,c900-plic
-add pvt node
-add thermal-zones
arch/riscv/boot/dts/thead/th1520.dtsi | 491 ++++++++++++++++++++++++++
1 file changed, 491 insertions(+)
create mode 100644 arch/riscv/boot/dts/thead/th1520.dtsi
diff --git a/arch/riscv/boot/dts/thead/th1520.dtsi b/arch/riscv/boot/dts/thead/th1520.dtsi
new file mode 100644
index 000000000000..d1d94098b6bf
--- /dev/null
+++ b/arch/riscv/boot/dts/thead/th1520.dtsi
@@ -0,0 +1,491 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Alibaba Group Holding Limited.
+ * Copyright (C) 2023 Jisheng Zhang <jszhang@kernel.org>
+ * Copyright (C) 2023 Yangtao Li <frank.li@vivo.com>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ compatible = "thead,th1520";
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus: cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ timebase-frequency = <3000000>;
+
+ c910_0: cpu@0 {
+ compatible = "thead,c910", "riscv";
+ device_type = "cpu";
+ riscv,isa = "rv64imafdc";
+ reg = <0>;
+ i-cache-block-size = <64>;
+ i-cache-size = <65536>;
+ i-cache-sets = <512>;
+ d-cache-block-size = <64>;
+ d-cache-size = <65536>;
+ d-cache-sets = <512>;
+ next-level-cache = <&l2_cache>;
+ mmu-type = "riscv,sv39";
+
+ cpu0_intc: interrupt-controller {
+ compatible = "riscv,cpu-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+ };
+
+ c910_1: cpu@1 {
+ compatible = "thead,c910", "riscv";
+ device_type = "cpu";
+ riscv,isa = "rv64imafdc";
+ reg = <1>;
+ i-cache-block-size = <64>;
+ i-cache-size = <65536>;
+ i-cache-sets = <512>;
+ d-cache-block-size = <64>;
+ d-cache-size = <65536>;
+ d-cache-sets = <512>;
+ next-level-cache = <&l2_cache>;
+ mmu-type = "riscv,sv39";
+
+ cpu1_intc: interrupt-controller {
+ compatible = "riscv,cpu-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+ };
+
+ c910_2: cpu@2 {
+ compatible = "thead,c910", "riscv";
+ device_type = "cpu";
+ riscv,isa = "rv64imafdc";
+ reg = <2>;
+ i-cache-block-size = <64>;
+ i-cache-size = <65536>;
+ i-cache-sets = <512>;
+ d-cache-block-size = <64>;
+ d-cache-size = <65536>;
+ d-cache-sets = <512>;
+ next-level-cache = <&l2_cache>;
+ mmu-type = "riscv,sv39";
+
+ cpu2_intc: interrupt-controller {
+ compatible = "riscv,cpu-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+ };
+
+ c910_3: cpu@3 {
+ compatible = "thead,c910", "riscv";
+ device_type = "cpu";
+ riscv,isa = "rv64imafdc";
+ reg = <3>;
+ i-cache-block-size = <64>;
+ i-cache-size = <65536>;
+ i-cache-sets = <512>;
+ d-cache-block-size = <64>;
+ d-cache-size = <65536>;
+ d-cache-sets = <512>;
+ next-level-cache = <&l2_cache>;
+ mmu-type = "riscv,sv39";
+
+ cpu3_intc: interrupt-controller {
+ compatible = "riscv,cpu-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&c910_0>;
+ };
+
+ core1 {
+ cpu = <&c910_1>;
+ };
+
+ core2 {
+ cpu = <&c910_2>;
+ };
+
+ core3 {
+ cpu = <&c910_3>;
+ };
+ };
+ };
+
+ l2_cache: l2-cache {
+ compatible = "cache";
+ cache-block-size = <64>;
+ cache-level = <2>;
+ cache-size = <1048576>;
+ cache-sets = <1024>;
+ cache-unified;
+ };
+ };
+
+ osc: oscillator {
+ compatible = "fixed-clock";
+ clock-output-names = "osc_24m";
+ #clock-cells = <0>;
+ };
+
+ osc_32k: 32k-oscillator {
+ compatible = "fixed-clock";
+ clock-output-names = "osc_32k";
+ #clock-cells = <0>;
+ };
+
+ apb_clk: apb-clk-clock {
+ compatible = "fixed-clock";
+ clock-output-names = "apb_clk";
+ #clock-cells = <0>;
+ };
+
+ uart_sclk: uart-sclk-clock {
+ compatible = "fixed-clock";
+ clock-output-names = "uart_sclk";
+ #clock-cells = <0>;
+ };
+
+ pvt_clk: pvt-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <73728000>;
+ clock-output-names = "pvt_clk";
+ #clock-cells = <0>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ interrupt-parent = <&plic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ plic: interrupt-controller@ffd8000000 {
+ compatible = "thead,c900-plic";
+ reg = <0xff 0xd8000000 0x0 0x01000000>;
+ interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>,
+ <&cpu1_intc 11>, <&cpu1_intc 9>,
+ <&cpu2_intc 11>, <&cpu2_intc 9>,
+ <&cpu3_intc 11>, <&cpu3_intc 9>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ riscv,ndev = <240>;
+
+ };
+
+ clint: timer@ffdc000000 {
+ compatible = "thead,c900-clint";
+ reg = <0xff 0xdc000000 0x0 0x00010000>;
+ interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>,
+ <&cpu1_intc 3>, <&cpu1_intc 7>,
+ <&cpu2_intc 3>, <&cpu2_intc 7>,
+ <&cpu3_intc 3>, <&cpu3_intc 7>;
+ };
+
+ uart0: serial@ffe7014000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0xff 0xe7014000 0x0 0x4000>;
+ interrupts = <36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uart_sclk>;
+ clock-names = "baudclk";
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart1: serial@ffe7f00000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0xff 0xe7f00000 0x0 0x4000>;
+ interrupts = <37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uart_sclk>;
+ clock-names = "baudclk";
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart3: serial@ffe7f04000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0xff 0xe7f04000 0x0 0x4000>;
+ interrupts = <39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uart_sclk>;
+ clock-names = "baudclk";
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ gpio2: gpio@ffe7f34000 {
+ compatible = "snps,dw-apb-gpio";
+ reg = <0xff 0xe7f34000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ portc: gpio-controller@0 {
+ compatible = "snps,dw-apb-gpio-port";
+ gpio-controller;
+ #gpio-cells = <2>;
+ ngpios = <32>;
+ reg = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <58 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ gpio3: gpio@ffe7f38000 {
+ compatible = "snps,dw-apb-gpio";
+ reg = <0xff 0xe7f38000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ portd: gpio-controller@0 {
+ compatible = "snps,dw-apb-gpio-port";
+ gpio-controller;
+ #gpio-cells = <2>;
+ ngpios = <32>;
+ reg = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <59 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ gpio0: gpio@ffec005000 {
+ compatible = "snps,dw-apb-gpio";
+ reg = <0xff 0xec005000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ porta: gpio-controller@0 {
+ compatible = "snps,dw-apb-gpio-port";
+ gpio-controller;
+ #gpio-cells = <2>;
+ ngpios = <32>;
+ reg = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <56 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ gpio1: gpio@ffec006000 {
+ compatible = "snps,dw-apb-gpio";
+ reg = <0xff 0xec006000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ portb: gpio-controller@0 {
+ compatible = "snps,dw-apb-gpio-port";
+ gpio-controller;
+ #gpio-cells = <2>;
+ ngpios = <32>;
+ reg = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <57 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ uart2: serial@ffec010000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0xff 0xec010000 0x0 0x4000>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uart_sclk>;
+ clock-names = "baudclk";
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ dmac0: dma-controller@ffefc00000 {
+ compatible = "snps,axi-dma-1.01a";
+ reg = <0xff 0xefc00000 0x0 0x1000>;
+ interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb_clk>, <&apb_clk>;
+ clock-names = "core-clk", "cfgr-clk";
+ #dma-cells = <1>;
+ dma-channels = <4>;
+ snps,block-size = <65536 65536 65536 65536>;
+ snps,priority = <0 1 2 3>;
+ snps,dma-masters = <1>;
+ snps,data-width = <4>;
+ snps,axi-max-burst-len = <16>;
+ status = "disabled";
+ };
+
+ timer0: timer@ffefc32000 {
+ compatible = "snps,dw-apb-timer";
+ reg = <0xff 0xefc32000 0x0 0x14>;
+ clocks = <&apb_clk>;
+ clock-names = "timer";
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ timer1: timer@ffefc32014 {
+ compatible = "snps,dw-apb-timer";
+ reg = <0xff 0xefc32014 0x0 0x14>;
+ clocks = <&apb_clk>;
+ clock-names = "timer";
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ timer2: timer@ffefc32028 {
+ compatible = "snps,dw-apb-timer";
+ reg = <0xff 0xefc32028 0x0 0x14>;
+ clocks = <&apb_clk>;
+ clock-names = "timer";
+ interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ timer3: timer@ffefc3203c {
+ compatible = "snps,dw-apb-timer";
+ reg = <0xff 0xefc3203c 0x0 0x14>;
+ clocks = <&apb_clk>;
+ clock-names = "timer";
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ uart4: serial@fff7f08000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0xff 0xf7f08000 0x0 0x4000>;
+ interrupts = <40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uart_sclk>;
+ clock-names = "baudclk";
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart5: serial@fff7f0c000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0xff 0xf7f0c000 0x0 0x4000>;
+ interrupts = <41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uart_sclk>;
+ clock-names = "baudclk";
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ timer4: timer@ffffc33000 {
+ compatible = "snps,dw-apb-timer";
+ reg = <0xff 0xffc33000 0x0 0x14>;
+ clocks = <&apb_clk>;
+ clock-names = "timer";
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ timer5: timer@ffffc33014 {
+ compatible = "snps,dw-apb-timer";
+ reg = <0xff 0xffc33014 0x0 0x14>;
+ clocks = <&apb_clk>;
+ clock-names = "timer";
+ interrupts = <21 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ timer6: timer@ffffc33028 {
+ compatible = "snps,dw-apb-timer";
+ reg = <0xff 0xffc33028 0x0 0x14>;
+ clocks = <&apb_clk>;
+ clock-names = "timer";
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ timer7: timer@ffffc3303c {
+ compatible = "snps,dw-apb-timer";
+ reg = <0xff 0xffc3303c 0x0 0x14>;
+ clocks = <&apb_clk>;
+ clock-names = "timer";
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ ao_gpio0: gpio@fffff41000 {
+ compatible = "snps,dw-apb-gpio";
+ reg = <0xff 0xfff41000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ porte: gpio-controller@0 {
+ compatible = "snps,dw-apb-gpio-port";
+ gpio-controller;
+ #gpio-cells = <2>;
+ ngpios = <32>;
+ reg = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <76 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ pvt: pvt@fffff4e000 {
+ compatible = "moortec,mr75203";
+ reg = <0xff 0xfff4e000 0x0 0x80>,
+ <0xff 0xfff4e080 0x0 0x100>,
+ <0xff 0xfff4e180 0x0 0x680>,
+ <0xff 0xfff4e800 0x0 0x600>;
+ reg-names = "common", "ts", "pd", "vm";
+ clocks = <&pvt_clk>;
+ /* TODO: add reset */
+ #thermal-sensor-cells = <1>;
+ status = "disabled";
+ };
+
+ ao_gpio1: gpio@fffff52000 {
+ compatible = "snps,dw-apb-gpio";
+ reg = <0xff 0xfff52000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ portf: gpio-controller@0 {
+ compatible = "snps,dw-apb-gpio-port";
+ gpio-controller;
+ #gpio-cells = <2>;
+ ngpios = <32>;
+ reg = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <55 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+ };
+
+ thermal-zones {
+ cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&pvt 0>;
+
+ trips {
+ trip0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
--
2.34.1
next parent reply other threads:[~2023-05-10 20:45 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20230510204456.57202-1-frank.li@vivo.com>
2023-05-10 20:44 ` Yangtao Li [this message]
2023-05-11 0:35 ` [PATCH v2 2/5] riscv: dts: add initial T-HEAD light SoC device tree Yixun Lan
2023-05-11 0:39 ` Jisheng Zhang
2023-05-11 9:05 ` Krzysztof Kozlowski
2023-05-10 20:44 ` [PATCH v2 3/5] riscv: dts: thead: add sipeed Lichee Pi 4A board " Yangtao Li
2023-05-11 0:42 ` Yixun Lan
2023-05-11 9:12 ` Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230510204456.57202-2-frank.li@vivo.com \
--to=frank.li@vivo.com \
--cc=aou@eecs.berkeley.edu \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jszhang@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=robh+dt@kernel.org \
--cc=uwu@icenowy.me \
--cc=wefu@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox