[PATCH V2 1/2] arm64: dts: imx8mn-beacon: Migrate sound card to simple-audio-card

[PATCH V2 1/2] arm64: dts: imx8mn-beacon: Migrate sound card to simple-audio-card

[Adam Ford]

Instead of using a custom glue layer connecting the wm8962 CODEC
to the SAI3 sound-dai, migrate the sound card to simple-audio-card.

Signed-off-by: Adam Ford <aford173@gmail.com>

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
index 6dce77a6114c..038ef8a3e604 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
@@ -74,18 +74,30 @@ reg_usb_otg_vbus: regulator-usb {
 		enable-active-high;
 	};
 
-	sound {
-		compatible = "fsl,imx-audio-wm8962";
-		model = "wm8962-audio";
-		audio-cpu = <&sai3>;
-		audio-codec = <&wm8962>;
-		audio-routing =
-			"Headphone Jack", "HPOUTL",
-			"Headphone Jack", "HPOUTR",
-			"Ext Spk", "SPKOUTL",
-			"Ext Spk", "SPKOUTR",
-			"AMIC", "MICBIAS",
-			"IN3R", "AMIC";
+	sound-wm8962 {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "wm8962";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets = "Headphone", "Headphones",
+					    "Microphone", "Headset Mic",
+					    "Speaker", "Speaker";
+		simple-audio-card,routing = "Headphones", "HPOUTL",
+					    "Headphones", "HPOUTR",
+					    "Speaker", "SPKOUTL",
+					    "Speaker", "SPKOUTR",
+					    "Headset Mic", "MICBIAS",
+					    "IN3R", "Headset Mic";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai3>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&wm8962>;
+			clocks = <&clk IMX8MN_CLK_SAI3_ROOT>;
+			frame-master;
+			bitclock-master;
+		};
 	};
 };
 
@@ -183,6 +195,7 @@ wm8962: audio-codec@1a {
 			0x0000 /* 4:FN_DMICCDAT */
 			0x0000 /* 5:Default */
 		>;
+		#sound-dai-cells = <0>;
 	};
 };
 
-- 
2.39.2

[PATCH V2 2/2] arm64: dts: imx8mn-beacon: Fix SPI CS pinmux

[Adam Ford]

The final production baseboard had a different chip select than
earlier prototype boards.  When the newer board was released,
the SPI stopped working because the wrong pin was used in the device
tree and conflicted with the UART RTS. Fix the pinmux for
production boards.

Fixes: 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
index 038ef8a3e604..16761975f56e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
@@ -104,7 +104,7 @@ simple-audio-card,codec {
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_espi2>;
-	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	eeprom@0 {
@@ -273,7 +273,7 @@ pinctrl_espi2: espi2grp {
 			MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
 			MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
 			MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
-			MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x41
+			MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x41
 		>;
 	};
 
-- 
2.39.2

Re: [PATCH V2 1/2] arm64: dts: imx8mn-beacon: Migrate sound card to simple-audio-card

[Shawn Guo]

On Sun, May 28, 2023 at 06:22:53AM -0500, Adam Ford wrote:
> Instead of using a custom glue layer connecting the wm8962 CODEC
> to the SAI3 sound-dai, migrate the sound card to simple-audio-card.
> 
> Signed-off-by: Adam Ford <aford173@gmail.com>

Applied both, thanks!