From: Sam Ravnborg <sam@ravnborg.org>
To: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Thierry Reding <thierry.reding@gmail.com>,
David Airlie <airlied@gmail.com>, Daniel Vetter <daniel@ffwll.ch>,
Maxime Ripard <mripard@kernel.org>,
dri-devel@lists.freedesktop.org, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
devicetree@vger.kernel.org,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Subject: Re: [PATCH 6/7] drm/panel: sitronix-st7789v: Add EDT ET028013DMA panel support
Date: Sat, 10 Jun 2023 22:22:51 +0200 [thread overview]
Message-ID: <20230610202251.GF1041001@ravnborg.org> (raw)
In-Reply-To: <20230609145951.853533-7-miquel.raynal@bootlin.com>
On Fri, Jun 09, 2023 at 04:59:50PM +0200, Miquel Raynal wrote:
> This panel from Emerging Display Technologies Corporation features an
> ST7789V2 panel inside which is almost identical to what the Sitronix
> panel driver supports.
>
> In practice, the module physical size is specific, and experiments show
> that the display will malfunction if any of the following situation
> occurs:
> * Pixel clock is above 3MHz
> * Pixel clock is not inverted
> I could not properly identify the reasons behind these failures, scope
> captures show valid input signals.
The patch includes an additional change where the bus_flags are assigned
to the connector. At least tell why, or maybe split it out.
Other panels could learn to do the same - and I assume you did it
because it was required in the atmel_hlcd driver.
Sam
>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
> .../gpu/drm/panel/panel-sitronix-st7789v.c | 34 +++++++++++++++++--
> 1 file changed, 32 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpu/drm/panel/panel-sitronix-st7789v.c b/drivers/gpu/drm/panel/panel-sitronix-st7789v.c
> index 212bccc31804..7de192a3a8aa 100644
> --- a/drivers/gpu/drm/panel/panel-sitronix-st7789v.c
> +++ b/drivers/gpu/drm/panel/panel-sitronix-st7789v.c
> @@ -30,7 +30,8 @@
> #define ST7789V_RGBCTRL_RCM(n) (((n) & 3) << 5)
> #define ST7789V_RGBCTRL_VSYNC_HIGH BIT(3)
> #define ST7789V_RGBCTRL_HSYNC_HIGH BIT(2)
> -#define ST7789V_RGBCTRL_PCLK_HIGH BIT(1)
> +#define ST7789V_RGBCTRL_PCLK_FALLING BIT(1)
> +#define ST7789V_RGBCTRL_PCLK_RISING 0
> #define ST7789V_RGBCTRL_VBP(n) ((n) & 0x7f)
> #define ST7789V_RGBCTRL_HBP(n) ((n) & 0x1f)
>
> @@ -117,6 +118,7 @@ struct st7789v_panel_info {
> u16 width_mm;
> u16 height_mm;
> u32 bus_format;
> + u32 bus_flags;
> };
>
> struct st7789v {
> @@ -175,6 +177,18 @@ static const struct drm_display_mode default_mode = {
> .vtotal = 320 + 8 + 4 + 4,
> };
>
> +static const struct drm_display_mode slow_mode = {
> + .clock = 3000,
> + .hdisplay = 240,
> + .hsync_start = 240 + 38,
> + .hsync_end = 240 + 38 + 10,
> + .htotal = 240 + 38 + 10 + 10,
> + .vdisplay = 320,
> + .vsync_start = 320 + 8,
> + .vsync_end = 320 + 8 + 4,
> + .vtotal = 320 + 8 + 4 + 4,
> +};
> +
> static int st7789v_get_modes(struct drm_panel *panel,
> struct drm_connector *connector)
> {
> @@ -197,6 +211,7 @@ static int st7789v_get_modes(struct drm_panel *panel,
>
> connector->display_info.width_mm = panel_info->width_mm;
> connector->display_info.height_mm = panel_info->height_mm;
> + connector->display_info.bus_flags = panel_info->bus_flags;
> drm_display_info_set_bus_formats(&connector->display_info,
> &panel_info->bus_format, 1);
>
> @@ -206,8 +221,13 @@ static int st7789v_get_modes(struct drm_panel *panel,
> static int st7789v_prepare(struct drm_panel *panel)
> {
> struct st7789v *ctx = panel_to_st7789v(panel);
> + const struct st7789v_panel_info *panel_info = ctx->panel_info;
> + u8 pck = ST7789V_RGBCTRL_PCLK_FALLING;
> int ret;
>
> + if (panel_info->bus_flags & DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE)
> + pck = ST7789V_RGBCTRL_PCLK_RISING;
> +
> ret = regulator_enable(ctx->power);
> if (ret)
> return ret;
> @@ -321,7 +341,7 @@ static int st7789v_prepare(struct drm_panel *panel)
> ST7789V_RGBCTRL_RCM(2) |
> ST7789V_RGBCTRL_VSYNC_HIGH |
> ST7789V_RGBCTRL_HSYNC_HIGH |
> - ST7789V_RGBCTRL_PCLK_HIGH));
> + pck));
> ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_RGBCTRL_VBP(8)));
> ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_RGBCTRL_HBP(20)));
>
> @@ -422,14 +442,24 @@ static const struct st7789v_panel_info st7789v_info = {
> .bus_format = MEDIA_BUS_FMT_RGB666_1X18,
> };
>
> +static const struct st7789v_panel_info et028013dma_info = {
> + .display_mode = &slow_mode,
> + .width_mm = 43,
> + .height_mm = 58,
> + .bus_format = MEDIA_BUS_FMT_RGB666_1X18,
> + .bus_flags = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
> +};
> +
> static const struct of_device_id st7789v_of_match[] = {
> { .compatible = "sitronix,st7789v", .data = &st7789v_info },
> + { .compatible = "edt,et028013dma", .data = &et028013dma_info },
> { }
> };
> MODULE_DEVICE_TABLE(of, st7789v_of_match);
>
> static const struct spi_device_id st7789v_ids[] = {
> { "st7789v", },
> + { "et028013dma", },
> { /* sentinel */ }
> };
> MODULE_DEVICE_TABLE(spi, st7789v_ids);
> --
> 2.34.1
next prev parent reply other threads:[~2023-06-10 20:24 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-09 14:59 [PATCH 0/7] drm/panel: sitronix-st7789v: Support ET028013DMA panel Miquel Raynal
2023-06-09 14:59 ` [PATCH 1/7] drm/panel: sitronix-st7789v: Prevent core spi warnings Miquel Raynal
2023-06-10 20:06 ` Sam Ravnborg
2023-06-13 6:15 ` Michael Riesch
2023-06-13 6:56 ` Miquel Raynal
2023-06-14 23:22 ` Sebastian Reichel
2023-06-15 5:43 ` Sam Ravnborg
2023-06-15 12:58 ` Sebastian Reichel
2023-06-09 14:59 ` [PATCH 2/7] drm/panel: sitronix-st7789v: Use 9 bits per spi word by default Miquel Raynal
2023-06-10 20:09 ` Sam Ravnborg
2023-06-09 14:59 ` [PATCH 3/7] drm/panel: sitronix-st7789v: Specify the expected bus format Miquel Raynal
2023-06-10 20:12 ` Sam Ravnborg
2023-06-16 9:56 ` Miquel Raynal
2023-06-12 8:44 ` Maxime Ripard
2023-06-09 14:59 ` [PATCH 4/7] drm/panel: sitronix-st7789v: Use platform data Miquel Raynal
2023-06-10 20:15 ` Sam Ravnborg
2023-06-09 14:59 ` [PATCH 5/7] dt-bindings: display: st7789v: Add the edt,et028013dma panel compatible Miquel Raynal
2023-06-09 14:59 ` [PATCH 6/7] drm/panel: sitronix-st7789v: Add EDT ET028013DMA panel support Miquel Raynal
2023-06-10 20:22 ` Sam Ravnborg [this message]
2023-06-12 8:51 ` Maxime Ripard
2023-06-16 10:01 ` Miquel Raynal
2023-06-09 14:59 ` [PATCH 7/7] drm/panel: sitronix-st7789v: Check display ID Miquel Raynal
2023-06-10 20:45 ` Sam Ravnborg
2023-06-14 23:27 ` Sebastian Reichel
2023-06-16 10:13 ` Miquel Raynal
2023-06-16 13:38 ` Sebastian Reichel
2023-06-13 6:25 ` Michael Riesch
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230610202251.GF1041001@ravnborg.org \
--to=sam@ravnborg.org \
--cc=airlied@gmail.com \
--cc=daniel@ffwll.ch \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=krzk+dt@kernel.org \
--cc=miquel.raynal@bootlin.com \
--cc=mripard@kernel.org \
--cc=robh+dt@kernel.org \
--cc=thierry.reding@gmail.com \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).