* [PATCH v3 0/2] typec: add support for the ON Semiconductor nb7vpq904m Type-C Linear Redriver
@ 2023-06-13 14:50 Neil Armstrong
2023-06-13 14:50 ` [PATCH v3 1/2] dt-bindings: usb: add ON Semiconductor nb7vpq904m Type-C Linear Redriver bindings Neil Armstrong
2023-06-13 14:50 ` [PATCH v3 2/2] usb: typec: add support for the nb7vpq904m Type-C Linear Redriver neil.armstrong
0 siblings, 2 replies; 7+ messages in thread
From: Neil Armstrong @ 2023-06-13 14:50 UTC (permalink / raw)
To: Greg Kroah-Hartman, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Bjorn Andersson, Heikki Krogerus, Liam Girdwood,
Mark Brown, Dmitry Baryshkov
Cc: linux-arm-msm, linux-usb, devicetree, linux-kernel,
Neil Armstrong
Add support for the ON Semiconductor NB7VPQ904M Type-C USB SuperSpeed
and DisplayPort ALT Mode Linear Redriver chip found on some devices
with a Type-C port.
The redriver compensates ultra High-Speeed DisplayPort and USB
Super Speed signal integrity losses mainly due to PCB & transmission
cables.
The redriver doesn't support SuperSpeed lines swapping, but
can support Type-C SBU lines swapping.
Support is designed as a Type-C Switch and Retimer, and can propagate
orientation settings to the source endpoint, which is usually
a Super Speed PHY which does the data lanes swapping.
Bindings are added first and can handle the fact data lanes pairs
can be swapped on the PCB.
Compile-time dependencies:
- svid removal at [1]
[1] https://lore.kernel.org/all/20230526131434.46920-1-heikki.krogerus@linux.intel.com/
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Changes in v3:
- Include bitfield.h
- Use correct -EOPNOTSUPP
- Correct nb7vpq904m_sw_set line wrapping
- Link to v2: https://lore.kernel.org/r/20230601-topic-sm8x50-upstream-redriver-v2-0-dda89b22b1c0@linaro.org
Changes in v2:
- Switch to "retimer" infrastructure
- Slight style fixups after switch to retimer
- Bindings updates (did not keep Reviewed-by tag for those reasons)
- Update maintainer, was using Bjorn with invalid email
- Fixed swapped lanes mapping
- Switched to retimer-switch
- Fixed i2c top node in example
- Link to v1: https://lore.kernel.org/r/20230601-topic-sm8x50-upstream-redriver-v1-0-6ad21094ff6f@linaro.org
---
Dmitry Baryshkov (1):
usb: typec: add support for the nb7vpq904m Type-C Linear Redriver
Neil Armstrong (1):
dt-bindings: usb: add ON Semiconductor nb7vpq904m Type-C Linear Redriver bindings
.../devicetree/bindings/usb/onnn,nb7vpq904m.yaml | 141 ++++++
drivers/usb/typec/mux/Kconfig | 8 +
drivers/usb/typec/mux/Makefile | 1 +
drivers/usb/typec/mux/nb7vpq904m.c | 529 +++++++++++++++++++++
4 files changed, 679 insertions(+)
---
base-commit: ac9a78681b921877518763ba0e89202254349d1b
change-id: 20230601-topic-sm8x50-upstream-redriver-6e261edd5cb4
Best regards,
--
Neil Armstrong <neil.armstrong@linaro.org>
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH v3 1/2] dt-bindings: usb: add ON Semiconductor nb7vpq904m Type-C Linear Redriver bindings 2023-06-13 14:50 [PATCH v3 0/2] typec: add support for the ON Semiconductor nb7vpq904m Type-C Linear Redriver Neil Armstrong @ 2023-06-13 14:50 ` Neil Armstrong 2023-06-13 18:23 ` Krzysztof Kozlowski 2023-06-13 14:50 ` [PATCH v3 2/2] usb: typec: add support for the nb7vpq904m Type-C Linear Redriver neil.armstrong 1 sibling, 1 reply; 7+ messages in thread From: Neil Armstrong @ 2023-06-13 14:50 UTC (permalink / raw) To: Greg Kroah-Hartman, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Bjorn Andersson, Heikki Krogerus, Liam Girdwood, Mark Brown, Dmitry Baryshkov Cc: linux-arm-msm, linux-usb, devicetree, linux-kernel, Neil Armstrong Document bindings for this ON Semiconductor Type-C USB SuperSpeed and DisplayPort ALT Mode Linear Redriver. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> --- .../devicetree/bindings/usb/onnn,nb7vpq904m.yaml | 141 +++++++++++++++++++++ 1 file changed, 141 insertions(+) diff --git a/Documentation/devicetree/bindings/usb/onnn,nb7vpq904m.yaml b/Documentation/devicetree/bindings/usb/onnn,nb7vpq904m.yaml new file mode 100644 index 000000000000..c0201da002f6 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/onnn,nb7vpq904m.yaml @@ -0,0 +1,141 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/onnn,nb7vpq904m.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ON Semiconductor Type-C DisplayPort ALT Mode Linear Redriver + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +properties: + compatible: + enum: + - onnn,nb7vpq904m + + reg: + maxItems: 1 + + vcc-supply: + description: power supply (1.8V) + + enable-gpios: true + + retimer-switch: + description: Flag the port as possible handle of SuperSpeed signals retiming + type: boolean + + orientation-switch: + description: Flag the port as possible handler of orientation switching + type: boolean + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: Super Speed (SS) Output endpoint to the Type-C connector + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + description: Super Speed (SS) Input endpoint from the Super-Speed PHY + unevaluatedProperties: false + + properties: + endpoint: + $ref: /schemas/graph.yaml#/$defs/endpoint-base + unevaluatedProperties: false + + properties: + data-lanes: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: | + An array of physical data lane indexes. Position determines how + lanes are connected to the redriver, It is assumed the same order + is kept on the other side of the redriver. + Lane number represents the following + - 0 is RX2 lane + - 1 is TX2 lane + - 2 is TX1 lane + - 3 is RX1 lane + The position determines the physical port of the redriver, in the + order A, B, C & D. + oneOf: + - items: + - const: 0 + - const: 1 + - const: 2 + - const: 3 + description: | + This is the lanes default layout + - Port A to RX2 lane + - Port B to TX2 lane + - Port C to TX1 lane + - Port D to RX1 lane + - items: + - const: 3 + - const: 2 + - const: 1 + - const: 0 + description: | + This is the USBRX2/USBTX2 and USBRX1/USBTX1 swapped lanes layout + - Port A to RX1 lane + - Port B to TX1 lane + - Port C to TX2 lane + - Port D to RX2 lane + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: + Sideband Use (SBU) AUX lines endpoint to the Type-C connector for the purpose of + handling altmode muxing and orientation switching. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + typec-mux@32 { + compatible = "onnn,nb7vpq904m"; + reg = <0x32>; + + vcc-supply = <&vreg_l15b_1p8>; + + retimer-switch; + orientation-switch; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + usb_con_ss: endpoint { + remote-endpoint = <&typec_con_ss>; + }; + }; + port@1 { + reg = <1>; + phy_con_ss: endpoint { + remote-endpoint = <&usb_phy_ss>; + data-lanes = <3 2 1 0>; + }; + }; + port@2 { + reg = <2>; + usb_con_sbu: endpoint { + remote-endpoint = <&typec_dp_aux>; + }; + }; + }; + }; + }; +... -- 2.34.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: usb: add ON Semiconductor nb7vpq904m Type-C Linear Redriver bindings 2023-06-13 14:50 ` [PATCH v3 1/2] dt-bindings: usb: add ON Semiconductor nb7vpq904m Type-C Linear Redriver bindings Neil Armstrong @ 2023-06-13 18:23 ` Krzysztof Kozlowski 0 siblings, 0 replies; 7+ messages in thread From: Krzysztof Kozlowski @ 2023-06-13 18:23 UTC (permalink / raw) To: Neil Armstrong, Greg Kroah-Hartman, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Bjorn Andersson, Heikki Krogerus, Liam Girdwood, Mark Brown, Dmitry Baryshkov Cc: linux-arm-msm, linux-usb, devicetree, linux-kernel On 13/06/2023 16:50, Neil Armstrong wrote: > Document bindings for this ON Semiconductor Type-C USB SuperSpeed > and DisplayPort ALT Mode Linear Redriver. > > Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> > --- Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Best regards, Krzysztof ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v3 2/2] usb: typec: add support for the nb7vpq904m Type-C Linear Redriver 2023-06-13 14:50 [PATCH v3 0/2] typec: add support for the ON Semiconductor nb7vpq904m Type-C Linear Redriver Neil Armstrong 2023-06-13 14:50 ` [PATCH v3 1/2] dt-bindings: usb: add ON Semiconductor nb7vpq904m Type-C Linear Redriver bindings Neil Armstrong @ 2023-06-13 14:50 ` neil.armstrong 2023-06-14 11:38 ` Heikki Krogerus 2023-06-15 9:47 ` Greg Kroah-Hartman 1 sibling, 2 replies; 7+ messages in thread From: neil.armstrong @ 2023-06-13 14:50 UTC (permalink / raw) To: Greg Kroah-Hartman, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Bjorn Andersson, Heikki Krogerus, Liam Girdwood, Mark Brown, Dmitry Baryshkov Cc: linux-arm-msm, linux-usb, devicetree, linux-kernel, Neil Armstrong From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Add support for the ON Semiconductor NB7VPQ904M Type-C USB SuperSpeed and DisplayPort ALT Mode Linear Redriver chip found on some devices with a Type-C port. The redriver compensates ultra High-Speeed DisplayPort and USB Super Speed signal integrity losses mainly due to PCB & transmission cables. The redriver doesn't support SuperSpeed lines swapping, but can support Type-C SBU lines swapping. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> --- drivers/usb/typec/mux/Kconfig | 8 + drivers/usb/typec/mux/Makefile | 1 + drivers/usb/typec/mux/nb7vpq904m.c | 529 +++++++++++++++++++++++++++++++++++++ 3 files changed, 538 insertions(+) diff --git a/drivers/usb/typec/mux/Kconfig b/drivers/usb/typec/mux/Kconfig index c46fa4f9d3df..8c4d6b8fb75c 100644 --- a/drivers/usb/typec/mux/Kconfig +++ b/drivers/usb/typec/mux/Kconfig @@ -35,4 +35,12 @@ config TYPEC_MUX_INTEL_PMC control the USB role switch and also the multiplexer/demultiplexer switches used with USB Type-C Alternate Modes. +config TYPEC_MUX_NB7VPQ904M + tristate "On Semiconductor NB7VPQ904M Type-C redriver driver" + depends on I2C + select REGMAP_I2C + help + Say Y or M if your system has a On Semiconductor NB7VPQ904M Type-C + redriver chip found on some devices with a Type-C port. + endmenu diff --git a/drivers/usb/typec/mux/Makefile b/drivers/usb/typec/mux/Makefile index dda67e19b58b..76196096ef41 100644 --- a/drivers/usb/typec/mux/Makefile +++ b/drivers/usb/typec/mux/Makefile @@ -4,3 +4,4 @@ obj-$(CONFIG_TYPEC_MUX_FSA4480) += fsa4480.o obj-$(CONFIG_TYPEC_MUX_GPIO_SBU) += gpio-sbu-mux.o obj-$(CONFIG_TYPEC_MUX_PI3USB30532) += pi3usb30532.o obj-$(CONFIG_TYPEC_MUX_INTEL_PMC) += intel_pmc_mux.o +obj-$(CONFIG_TYPEC_MUX_NB7VPQ904M) += nb7vpq904m.o diff --git a/drivers/usb/typec/mux/nb7vpq904m.c b/drivers/usb/typec/mux/nb7vpq904m.c new file mode 100644 index 000000000000..5157705c2f66 --- /dev/null +++ b/drivers/usb/typec/mux/nb7vpq904m.c @@ -0,0 +1,529 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * OnSemi NB7VPQ904M Type-C driver + * + * Copyright (C) 2023 Dmitry Baryshkov <dmitry.baryshkov@linaro.org> + */ +#include <linux/i2c.h> +#include <linux/mutex.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/bitfield.h> +#include <linux/of_graph.h> +#include <drm/drm_bridge.h> +#include <linux/usb/typec_dp.h> +#include <linux/usb/typec_mux.h> +#include <linux/usb/typec_retimer.h> +#include <linux/gpio/consumer.h> +#include <linux/regulator/consumer.h> + +#define NB7_CHNA 0 +#define NB7_CHNB 1 +#define NB7_CHNC 2 +#define NB7_CHND 3 +#define NB7_IS_CHAN_AD(channel) (channel == NB7_CHNA || channel == NB7_CHND) + +#define GEN_DEV_SET_REG 0x00 + +#define GEN_DEV_SET_CHIP_EN BIT(0) +#define GEN_DEV_SET_CHNA_EN BIT(4) +#define GEN_DEV_SET_CHNB_EN BIT(5) +#define GEN_DEV_SET_CHNC_EN BIT(6) +#define GEN_DEV_SET_CHND_EN BIT(7) + +#define GEN_DEV_SET_OP_MODE_MASK GENMASK(3, 1) + +#define GEN_DEV_SET_OP_MODE_DP_CC2 0 +#define GEN_DEV_SET_OP_MODE_DP_CC1 1 +#define GEN_DEV_SET_OP_MODE_DP_4LANE 2 +#define GEN_DEV_SET_OP_MODE_USB 5 + +#define EQ_SETTING_REG_BASE 0x01 +#define EQ_SETTING_REG(n) (EQ_SETTING_REG_BASE + (n) * 2) +#define EQ_SETTING_MASK GENMASK(3, 1) + +#define OUTPUT_COMPRESSION_AND_POL_REG_BASE 0x02 +#define OUTPUT_COMPRESSION_AND_POL_REG(n) (OUTPUT_COMPRESSION_AND_POL_REG_BASE + (n) * 2) +#define OUTPUT_COMPRESSION_MASK GENMASK(2, 1) + +#define FLAT_GAIN_REG_BASE 0x18 +#define FLAT_GAIN_REG(n) (FLAT_GAIN_REG_BASE + (n) * 2) +#define FLAT_GAIN_MASK GENMASK(1, 0) + +#define LOSS_MATCH_REG_BASE 0x19 +#define LOSS_MATCH_REG(n) (LOSS_MATCH_REG_BASE + (n) * 2) +#define LOSS_MATCH_MASK GENMASK(1, 0) + +#define AUX_CC_REG 0x09 + +#define CHIP_VERSION_REG 0x17 + +struct nb7vpq904m { + struct i2c_client *client; + struct gpio_desc *enable_gpio; + struct regulator *vcc_supply; + struct regmap *regmap; + struct typec_switch_dev *sw; + struct typec_retimer *retimer; + + bool swap_data_lanes; + struct typec_switch *typec_switch; + + struct drm_bridge bridge; + + struct mutex lock; /* protect non-concurrent retimer & switch */ + + enum typec_orientation orientation; + unsigned long mode; + unsigned int svid; +}; + +static void nb7vpq904m_set_channel(struct nb7vpq904m *nb7, unsigned int channel, bool dp) +{ + u8 eq, out_comp, flat_gain, loss_match; + + if (dp) { + eq = NB7_IS_CHAN_AD(channel) ? 0x6 : 0x4; + out_comp = 0x3; + flat_gain = NB7_IS_CHAN_AD(channel) ? 0x2 : 0x1; + loss_match = 0x3; + } else { + eq = 0x4; + out_comp = 0x3; + flat_gain = NB7_IS_CHAN_AD(channel) ? 0x3 : 0x1; + loss_match = NB7_IS_CHAN_AD(channel) ? 0x1 : 0x3; + } + + regmap_update_bits(nb7->regmap, EQ_SETTING_REG(channel), + EQ_SETTING_MASK, FIELD_PREP(EQ_SETTING_MASK, eq)); + regmap_update_bits(nb7->regmap, OUTPUT_COMPRESSION_AND_POL_REG(channel), + OUTPUT_COMPRESSION_MASK, FIELD_PREP(OUTPUT_COMPRESSION_MASK, out_comp)); + regmap_update_bits(nb7->regmap, FLAT_GAIN_REG(channel), + FLAT_GAIN_MASK, FIELD_PREP(FLAT_GAIN_MASK, flat_gain)); + regmap_update_bits(nb7->regmap, LOSS_MATCH_REG(channel), + LOSS_MATCH_MASK, FIELD_PREP(LOSS_MATCH_MASK, loss_match)); +} + +static int nb7vpq904m_set(struct nb7vpq904m *nb7) +{ + bool reverse = (nb7->orientation == TYPEC_ORIENTATION_REVERSE); + + switch (nb7->mode) { + case TYPEC_STATE_SAFE: + regmap_write(nb7->regmap, GEN_DEV_SET_REG, + GEN_DEV_SET_CHIP_EN | + GEN_DEV_SET_CHNA_EN | + GEN_DEV_SET_CHNB_EN | + GEN_DEV_SET_CHNC_EN | + GEN_DEV_SET_CHND_EN | + FIELD_PREP(GEN_DEV_SET_OP_MODE_MASK, + GEN_DEV_SET_OP_MODE_USB)); + nb7vpq904m_set_channel(nb7, NB7_CHNA, false); + nb7vpq904m_set_channel(nb7, NB7_CHNB, false); + nb7vpq904m_set_channel(nb7, NB7_CHNC, false); + nb7vpq904m_set_channel(nb7, NB7_CHND, false); + regmap_write(nb7->regmap, AUX_CC_REG, 0x2); + + return 0; + + case TYPEC_STATE_USB: + /* + * Normal Orientation (CC1) + * A -> USB RX + * B -> USB TX + * C -> X + * D -> X + * Flipped Orientation (CC2) + * A -> X + * B -> X + * C -> USB TX + * D -> USB RX + * + * Reversed if data lanes are swapped + */ + if (reverse ^ nb7->swap_data_lanes) { + regmap_write(nb7->regmap, GEN_DEV_SET_REG, + GEN_DEV_SET_CHIP_EN | + GEN_DEV_SET_CHNA_EN | + GEN_DEV_SET_CHNB_EN | + FIELD_PREP(GEN_DEV_SET_OP_MODE_MASK, + GEN_DEV_SET_OP_MODE_USB)); + nb7vpq904m_set_channel(nb7, NB7_CHNA, false); + nb7vpq904m_set_channel(nb7, NB7_CHNB, false); + } else { + regmap_write(nb7->regmap, GEN_DEV_SET_REG, + GEN_DEV_SET_CHIP_EN | + GEN_DEV_SET_CHNC_EN | + GEN_DEV_SET_CHND_EN | + FIELD_PREP(GEN_DEV_SET_OP_MODE_MASK, + GEN_DEV_SET_OP_MODE_USB)); + nb7vpq904m_set_channel(nb7, NB7_CHNC, false); + nb7vpq904m_set_channel(nb7, NB7_CHND, false); + } + regmap_write(nb7->regmap, AUX_CC_REG, 0x2); + + return 0; + + default: + if (nb7->svid != USB_TYPEC_DP_SID) + return -EINVAL; + + break; + } + + /* DP Altmode Setup */ + + regmap_write(nb7->regmap, AUX_CC_REG, reverse ? 0x1 : 0x0); + + switch (nb7->mode) { + case TYPEC_DP_STATE_C: + case TYPEC_DP_STATE_E: + /* + * Normal Orientation (CC1) + * A -> DP3 + * B -> DP2 + * C -> DP1 + * D -> DP0 + * Flipped Orientation (CC2) + * A -> DP0 + * B -> DP1 + * C -> DP2 + * D -> DP3 + */ + regmap_write(nb7->regmap, GEN_DEV_SET_REG, + GEN_DEV_SET_CHIP_EN | + GEN_DEV_SET_CHNA_EN | + GEN_DEV_SET_CHNB_EN | + GEN_DEV_SET_CHNC_EN | + GEN_DEV_SET_CHND_EN | + FIELD_PREP(GEN_DEV_SET_OP_MODE_MASK, + GEN_DEV_SET_OP_MODE_DP_4LANE)); + nb7vpq904m_set_channel(nb7, NB7_CHNA, true); + nb7vpq904m_set_channel(nb7, NB7_CHNB, true); + nb7vpq904m_set_channel(nb7, NB7_CHNC, true); + nb7vpq904m_set_channel(nb7, NB7_CHND, true); + break; + + case TYPEC_DP_STATE_D: + case TYPEC_DP_STATE_F: + regmap_write(nb7->regmap, GEN_DEV_SET_REG, + GEN_DEV_SET_CHIP_EN | + GEN_DEV_SET_CHNA_EN | + GEN_DEV_SET_CHNB_EN | + GEN_DEV_SET_CHNC_EN | + GEN_DEV_SET_CHND_EN | + FIELD_PREP(GEN_DEV_SET_OP_MODE_MASK, + reverse ^ nb7->swap_data_lanes ? + GEN_DEV_SET_OP_MODE_DP_CC2 + : GEN_DEV_SET_OP_MODE_DP_CC1)); + + /* + * Normal Orientation (CC1) + * A -> USB RX + * B -> USB TX + * C -> DP1 + * D -> DP0 + * Flipped Orientation (CC2) + * A -> DP0 + * B -> DP1 + * C -> USB TX + * D -> USB RX + * + * Reversed if data lanes are swapped + */ + if (nb7->swap_data_lanes) { + nb7vpq904m_set_channel(nb7, NB7_CHNA, !reverse); + nb7vpq904m_set_channel(nb7, NB7_CHNB, !reverse); + nb7vpq904m_set_channel(nb7, NB7_CHNC, reverse); + nb7vpq904m_set_channel(nb7, NB7_CHND, reverse); + } else { + nb7vpq904m_set_channel(nb7, NB7_CHNA, reverse); + nb7vpq904m_set_channel(nb7, NB7_CHNB, reverse); + nb7vpq904m_set_channel(nb7, NB7_CHNC, !reverse); + nb7vpq904m_set_channel(nb7, NB7_CHND, !reverse); + } + break; + + default: + return -EOPNOTSUPP; + } + + return 0; +} + +static int nb7vpq904m_sw_set(struct typec_switch_dev *sw, enum typec_orientation orientation) +{ + struct nb7vpq904m *nb7 = typec_switch_get_drvdata(sw); + int ret; + + ret = typec_switch_set(nb7->typec_switch, orientation); + if (ret) + return ret; + + mutex_lock(&nb7->lock); + + if (nb7->orientation != orientation) { + nb7->orientation = orientation; + + ret = nb7vpq904m_set(nb7); + } + + mutex_unlock(&nb7->lock); + + return ret; +} + +static int nb7vpq904m_retimer_set(struct typec_retimer *retimer, struct typec_retimer_state *state) +{ + struct nb7vpq904m *nb7 = typec_retimer_get_drvdata(retimer); + int ret = 0; + + mutex_lock(&nb7->lock); + + if (nb7->mode != state->mode) { + nb7->mode = state->mode; + + if (state->alt) + nb7->svid = state->alt->svid; + else + nb7->svid = 0; // No SVID + + ret = nb7vpq904m_set(nb7); + } + + mutex_unlock(&nb7->lock); + + return ret; +} + +#if IS_ENABLED(CONFIG_DRM) +static int nb7vpq904m_bridge_attach(struct drm_bridge *bridge, + enum drm_bridge_attach_flags flags) +{ + struct nb7vpq904m *nb7 = container_of(bridge, struct nb7vpq904m, bridge); + struct drm_bridge *next_bridge; + + if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) + return -EINVAL; + + next_bridge = devm_drm_of_get_bridge(&nb7->client->dev, nb7->client->dev.of_node, 0, 0); + if (IS_ERR(next_bridge)) { + dev_err(&nb7->client->dev, "failed to acquire drm_bridge: %pe\n", next_bridge); + return PTR_ERR(next_bridge); + } + + return drm_bridge_attach(bridge->encoder, next_bridge, bridge, + DRM_BRIDGE_ATTACH_NO_CONNECTOR); +} + +static const struct drm_bridge_funcs nb7vpq904m_bridge_funcs = { + .attach = nb7vpq904m_bridge_attach, +}; + +static int nb7vpq904m_register_bridge(struct nb7vpq904m *nb7) +{ + nb7->bridge.funcs = &nb7vpq904m_bridge_funcs; + nb7->bridge.of_node = nb7->client->dev.of_node; + + return devm_drm_bridge_add(&nb7->client->dev, &nb7->bridge); +} +#else +static int nb7vpq904m_register_bridge(struct nb7vpq904m *nb7) +{ + return 0; +} +#endif + +static const struct regmap_config nb7_regmap = { + .max_register = 0x1f, + .reg_bits = 8, + .val_bits = 8, +}; + +enum { + NORMAL_LANE_MAPPING, + INVERT_LANE_MAPPING, +}; + +#define DATA_LANES_COUNT 4 + +static const int supported_data_lane_mapping[][DATA_LANES_COUNT] = { + [NORMAL_LANE_MAPPING] = { 0, 1, 2, 3 }, + [INVERT_LANE_MAPPING] = { 3, 2, 1, 0 }, +}; + +static int nb7vpq904m_parse_data_lanes_mapping(struct nb7vpq904m *nb7) +{ + struct device_node *ep; + u32 data_lanes[4]; + int ret, i, j; + + ep = of_graph_get_endpoint_by_regs(nb7->client->dev.of_node, 1, 0); + + if (ep) { + ret = of_property_count_u32_elems(ep, "data-lanes"); + if (ret == -EINVAL) + /* Property isn't here, consider default mapping */ + goto out_done; + if (ret < 0) + goto out_error; + + if (ret != DATA_LANES_COUNT) { + dev_err(&nb7->client->dev, "expected 4 data lanes\n"); + ret = -EINVAL; + goto out_error; + } + + ret = of_property_read_u32_array(ep, "data-lanes", data_lanes, DATA_LANES_COUNT); + if (ret) + goto out_error; + + for (i = 0; i < ARRAY_SIZE(supported_data_lane_mapping); i++) { + for (j = 0; j < DATA_LANES_COUNT; j++) { + if (data_lanes[j] != supported_data_lane_mapping[i][j]) + break; + } + + if (j == DATA_LANES_COUNT) + break; + } + + switch (i) { + case NORMAL_LANE_MAPPING: + break; + case INVERT_LANE_MAPPING: + nb7->swap_data_lanes = true; + dev_info(&nb7->client->dev, "using inverted data lanes mapping\n"); + break; + default: + dev_err(&nb7->client->dev, "invalid data lanes mapping\n"); + ret = -EINVAL; + goto out_error; + } + } + +out_done: + ret = 0; + +out_error: + of_node_put(ep); + + return ret; +} + +static int nb7vpq904m_probe(struct i2c_client *client) +{ + struct device *dev = &client->dev; + struct typec_switch_desc sw_desc = { }; + struct typec_retimer_desc retimer_desc = { }; + struct nb7vpq904m *nb7; + int ret; + + nb7 = devm_kzalloc(dev, sizeof(*nb7), GFP_KERNEL); + if (!nb7) + return -ENOMEM; + + nb7->client = client; + + nb7->regmap = devm_regmap_init_i2c(client, &nb7_regmap); + if (IS_ERR(nb7->regmap)) { + dev_err(&client->dev, "Failed to allocate register map\n"); + return PTR_ERR(nb7->regmap); + } + + nb7->mode = TYPEC_STATE_SAFE; + nb7->orientation = TYPEC_ORIENTATION_NONE; + + mutex_init(&nb7->lock); + + nb7->enable_gpio = devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW); + if (IS_ERR(nb7->enable_gpio)) + return dev_err_probe(dev, PTR_ERR(nb7->enable_gpio), + "unable to acquire enable gpio\n"); + + nb7->vcc_supply = devm_regulator_get_optional(dev, "vcc"); + if (IS_ERR(nb7->vcc_supply)) + return PTR_ERR(nb7->vcc_supply); + + nb7->typec_switch = fwnode_typec_switch_get(dev->fwnode); + if (IS_ERR(nb7->typec_switch)) + return dev_err_probe(dev, PTR_ERR(nb7->typec_switch), + "failed to acquire orientation-switch\n"); + + ret = nb7vpq904m_parse_data_lanes_mapping(nb7); + if (ret) + return ret; + + ret = regulator_enable(nb7->vcc_supply); + if (ret) + dev_warn(dev, "Failed to enable vcc: %d\n", ret); + + gpiod_set_value(nb7->enable_gpio, 1); + + ret = nb7vpq904m_register_bridge(nb7); + if (ret) + return ret; + + sw_desc.drvdata = nb7; + sw_desc.fwnode = dev->fwnode; + sw_desc.set = nb7vpq904m_sw_set; + + nb7->sw = typec_switch_register(dev, &sw_desc); + if (IS_ERR(nb7->sw)) + return dev_err_probe(dev, PTR_ERR(nb7->sw), + "Error registering typec switch\n"); + + retimer_desc.drvdata = nb7; + retimer_desc.fwnode = dev->fwnode; + retimer_desc.set = nb7vpq904m_retimer_set; + + nb7->retimer = typec_retimer_register(dev, &retimer_desc); + if (IS_ERR(nb7->retimer)) { + typec_switch_unregister(nb7->sw); + return dev_err_probe(dev, PTR_ERR(nb7->retimer), + "Error registering typec retimer\n"); + } + + return 0; +} + +static void nb7vpq904m_remove(struct i2c_client *client) +{ + struct nb7vpq904m *nb7 = i2c_get_clientdata(client); + + typec_retimer_unregister(nb7->retimer); + typec_switch_unregister(nb7->sw); + + gpiod_set_value(nb7->enable_gpio, 0); + + regulator_disable(nb7->vcc_supply); +} + +static const struct i2c_device_id nb7vpq904m_table[] = { + { "nb7vpq904m" }, + { } +}; +MODULE_DEVICE_TABLE(i2c, nb7vpq904m_table); + +static const struct of_device_id nb7vpq904m_of_table[] = { + { .compatible = "onnn,nb7vpq904m" }, + { } +}; +MODULE_DEVICE_TABLE(of, nb7vpq904m_of_table); + +static struct i2c_driver nb7vpq904m_driver = { + .driver = { + .name = "nb7vpq904m", + .of_match_table = nb7vpq904m_of_table, + }, + .probe_new = nb7vpq904m_probe, + .remove = nb7vpq904m_remove, + .id_table = nb7vpq904m_table, +}; + +module_i2c_driver(nb7vpq904m_driver); + +MODULE_AUTHOR("Dmitry Baryshkov <dmitry.baryshkov@linaro.org>"); +MODULE_DESCRIPTION("OnSemi NB7VPQ904M Type-C driver"); +MODULE_LICENSE("GPL"); -- 2.34.1 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v3 2/2] usb: typec: add support for the nb7vpq904m Type-C Linear Redriver 2023-06-13 14:50 ` [PATCH v3 2/2] usb: typec: add support for the nb7vpq904m Type-C Linear Redriver neil.armstrong @ 2023-06-14 11:38 ` Heikki Krogerus 2023-06-15 9:47 ` Greg Kroah-Hartman 1 sibling, 0 replies; 7+ messages in thread From: Heikki Krogerus @ 2023-06-14 11:38 UTC (permalink / raw) To: neil.armstrong Cc: Greg Kroah-Hartman, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Bjorn Andersson, Liam Girdwood, Mark Brown, Dmitry Baryshkov, linux-arm-msm, linux-usb, devicetree, linux-kernel On Tue, Jun 13, 2023 at 04:50:08PM +0200, neil.armstrong@linaro.org wrote: > From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > > Add support for the ON Semiconductor NB7VPQ904M Type-C USB SuperSpeed > and DisplayPort ALT Mode Linear Redriver chip found on some devices > with a Type-C port. > > The redriver compensates ultra High-Speeed DisplayPort and USB > Super Speed signal integrity losses mainly due to PCB & transmission > cables. > > The redriver doesn't support SuperSpeed lines swapping, but > can support Type-C SBU lines swapping. > > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> > --- > drivers/usb/typec/mux/Kconfig | 8 + > drivers/usb/typec/mux/Makefile | 1 + > drivers/usb/typec/mux/nb7vpq904m.c | 529 +++++++++++++++++++++++++++++++++++++ > 3 files changed, 538 insertions(+) > > diff --git a/drivers/usb/typec/mux/Kconfig b/drivers/usb/typec/mux/Kconfig > index c46fa4f9d3df..8c4d6b8fb75c 100644 > --- a/drivers/usb/typec/mux/Kconfig > +++ b/drivers/usb/typec/mux/Kconfig > @@ -35,4 +35,12 @@ config TYPEC_MUX_INTEL_PMC > control the USB role switch and also the multiplexer/demultiplexer > switches used with USB Type-C Alternate Modes. > > +config TYPEC_MUX_NB7VPQ904M > + tristate "On Semiconductor NB7VPQ904M Type-C redriver driver" > + depends on I2C > + select REGMAP_I2C > + help > + Say Y or M if your system has a On Semiconductor NB7VPQ904M Type-C > + redriver chip found on some devices with a Type-C port. > + > endmenu > diff --git a/drivers/usb/typec/mux/Makefile b/drivers/usb/typec/mux/Makefile > index dda67e19b58b..76196096ef41 100644 > --- a/drivers/usb/typec/mux/Makefile > +++ b/drivers/usb/typec/mux/Makefile > @@ -4,3 +4,4 @@ obj-$(CONFIG_TYPEC_MUX_FSA4480) += fsa4480.o > obj-$(CONFIG_TYPEC_MUX_GPIO_SBU) += gpio-sbu-mux.o > obj-$(CONFIG_TYPEC_MUX_PI3USB30532) += pi3usb30532.o > obj-$(CONFIG_TYPEC_MUX_INTEL_PMC) += intel_pmc_mux.o > +obj-$(CONFIG_TYPEC_MUX_NB7VPQ904M) += nb7vpq904m.o > diff --git a/drivers/usb/typec/mux/nb7vpq904m.c b/drivers/usb/typec/mux/nb7vpq904m.c > new file mode 100644 > index 000000000000..5157705c2f66 > --- /dev/null > +++ b/drivers/usb/typec/mux/nb7vpq904m.c > @@ -0,0 +1,529 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * OnSemi NB7VPQ904M Type-C driver > + * > + * Copyright (C) 2023 Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > + */ > +#include <linux/i2c.h> > +#include <linux/mutex.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > +#include <linux/bitfield.h> > +#include <linux/of_graph.h> > +#include <drm/drm_bridge.h> > +#include <linux/usb/typec_dp.h> > +#include <linux/usb/typec_mux.h> > +#include <linux/usb/typec_retimer.h> > +#include <linux/gpio/consumer.h> > +#include <linux/regulator/consumer.h> > + > +#define NB7_CHNA 0 > +#define NB7_CHNB 1 > +#define NB7_CHNC 2 > +#define NB7_CHND 3 > +#define NB7_IS_CHAN_AD(channel) (channel == NB7_CHNA || channel == NB7_CHND) > + > +#define GEN_DEV_SET_REG 0x00 > + > +#define GEN_DEV_SET_CHIP_EN BIT(0) > +#define GEN_DEV_SET_CHNA_EN BIT(4) > +#define GEN_DEV_SET_CHNB_EN BIT(5) > +#define GEN_DEV_SET_CHNC_EN BIT(6) > +#define GEN_DEV_SET_CHND_EN BIT(7) > + > +#define GEN_DEV_SET_OP_MODE_MASK GENMASK(3, 1) > + > +#define GEN_DEV_SET_OP_MODE_DP_CC2 0 > +#define GEN_DEV_SET_OP_MODE_DP_CC1 1 > +#define GEN_DEV_SET_OP_MODE_DP_4LANE 2 > +#define GEN_DEV_SET_OP_MODE_USB 5 > + > +#define EQ_SETTING_REG_BASE 0x01 > +#define EQ_SETTING_REG(n) (EQ_SETTING_REG_BASE + (n) * 2) > +#define EQ_SETTING_MASK GENMASK(3, 1) > + > +#define OUTPUT_COMPRESSION_AND_POL_REG_BASE 0x02 > +#define OUTPUT_COMPRESSION_AND_POL_REG(n) (OUTPUT_COMPRESSION_AND_POL_REG_BASE + (n) * 2) > +#define OUTPUT_COMPRESSION_MASK GENMASK(2, 1) > + > +#define FLAT_GAIN_REG_BASE 0x18 > +#define FLAT_GAIN_REG(n) (FLAT_GAIN_REG_BASE + (n) * 2) > +#define FLAT_GAIN_MASK GENMASK(1, 0) > + > +#define LOSS_MATCH_REG_BASE 0x19 > +#define LOSS_MATCH_REG(n) (LOSS_MATCH_REG_BASE + (n) * 2) > +#define LOSS_MATCH_MASK GENMASK(1, 0) > + > +#define AUX_CC_REG 0x09 > + > +#define CHIP_VERSION_REG 0x17 > + > +struct nb7vpq904m { > + struct i2c_client *client; > + struct gpio_desc *enable_gpio; > + struct regulator *vcc_supply; > + struct regmap *regmap; > + struct typec_switch_dev *sw; > + struct typec_retimer *retimer; > + > + bool swap_data_lanes; > + struct typec_switch *typec_switch; > + > + struct drm_bridge bridge; > + > + struct mutex lock; /* protect non-concurrent retimer & switch */ > + > + enum typec_orientation orientation; > + unsigned long mode; > + unsigned int svid; > +}; > + > +static void nb7vpq904m_set_channel(struct nb7vpq904m *nb7, unsigned int channel, bool dp) > +{ > + u8 eq, out_comp, flat_gain, loss_match; > + > + if (dp) { > + eq = NB7_IS_CHAN_AD(channel) ? 0x6 : 0x4; > + out_comp = 0x3; > + flat_gain = NB7_IS_CHAN_AD(channel) ? 0x2 : 0x1; > + loss_match = 0x3; > + } else { > + eq = 0x4; > + out_comp = 0x3; > + flat_gain = NB7_IS_CHAN_AD(channel) ? 0x3 : 0x1; > + loss_match = NB7_IS_CHAN_AD(channel) ? 0x1 : 0x3; > + } > + > + regmap_update_bits(nb7->regmap, EQ_SETTING_REG(channel), > + EQ_SETTING_MASK, FIELD_PREP(EQ_SETTING_MASK, eq)); > + regmap_update_bits(nb7->regmap, OUTPUT_COMPRESSION_AND_POL_REG(channel), > + OUTPUT_COMPRESSION_MASK, FIELD_PREP(OUTPUT_COMPRESSION_MASK, out_comp)); > + regmap_update_bits(nb7->regmap, FLAT_GAIN_REG(channel), > + FLAT_GAIN_MASK, FIELD_PREP(FLAT_GAIN_MASK, flat_gain)); > + regmap_update_bits(nb7->regmap, LOSS_MATCH_REG(channel), > + LOSS_MATCH_MASK, FIELD_PREP(LOSS_MATCH_MASK, loss_match)); > +} > + > +static int nb7vpq904m_set(struct nb7vpq904m *nb7) > +{ > + bool reverse = (nb7->orientation == TYPEC_ORIENTATION_REVERSE); > + > + switch (nb7->mode) { > + case TYPEC_STATE_SAFE: > + regmap_write(nb7->regmap, GEN_DEV_SET_REG, > + GEN_DEV_SET_CHIP_EN | > + GEN_DEV_SET_CHNA_EN | > + GEN_DEV_SET_CHNB_EN | > + GEN_DEV_SET_CHNC_EN | > + GEN_DEV_SET_CHND_EN | > + FIELD_PREP(GEN_DEV_SET_OP_MODE_MASK, > + GEN_DEV_SET_OP_MODE_USB)); > + nb7vpq904m_set_channel(nb7, NB7_CHNA, false); > + nb7vpq904m_set_channel(nb7, NB7_CHNB, false); > + nb7vpq904m_set_channel(nb7, NB7_CHNC, false); > + nb7vpq904m_set_channel(nb7, NB7_CHND, false); > + regmap_write(nb7->regmap, AUX_CC_REG, 0x2); > + > + return 0; > + > + case TYPEC_STATE_USB: > + /* > + * Normal Orientation (CC1) > + * A -> USB RX > + * B -> USB TX > + * C -> X > + * D -> X > + * Flipped Orientation (CC2) > + * A -> X > + * B -> X > + * C -> USB TX > + * D -> USB RX > + * > + * Reversed if data lanes are swapped > + */ > + if (reverse ^ nb7->swap_data_lanes) { > + regmap_write(nb7->regmap, GEN_DEV_SET_REG, > + GEN_DEV_SET_CHIP_EN | > + GEN_DEV_SET_CHNA_EN | > + GEN_DEV_SET_CHNB_EN | > + FIELD_PREP(GEN_DEV_SET_OP_MODE_MASK, > + GEN_DEV_SET_OP_MODE_USB)); > + nb7vpq904m_set_channel(nb7, NB7_CHNA, false); > + nb7vpq904m_set_channel(nb7, NB7_CHNB, false); > + } else { > + regmap_write(nb7->regmap, GEN_DEV_SET_REG, > + GEN_DEV_SET_CHIP_EN | > + GEN_DEV_SET_CHNC_EN | > + GEN_DEV_SET_CHND_EN | > + FIELD_PREP(GEN_DEV_SET_OP_MODE_MASK, > + GEN_DEV_SET_OP_MODE_USB)); > + nb7vpq904m_set_channel(nb7, NB7_CHNC, false); > + nb7vpq904m_set_channel(nb7, NB7_CHND, false); > + } > + regmap_write(nb7->regmap, AUX_CC_REG, 0x2); > + > + return 0; > + > + default: > + if (nb7->svid != USB_TYPEC_DP_SID) > + return -EINVAL; > + > + break; > + } > + > + /* DP Altmode Setup */ > + > + regmap_write(nb7->regmap, AUX_CC_REG, reverse ? 0x1 : 0x0); > + > + switch (nb7->mode) { > + case TYPEC_DP_STATE_C: > + case TYPEC_DP_STATE_E: > + /* > + * Normal Orientation (CC1) > + * A -> DP3 > + * B -> DP2 > + * C -> DP1 > + * D -> DP0 > + * Flipped Orientation (CC2) > + * A -> DP0 > + * B -> DP1 > + * C -> DP2 > + * D -> DP3 > + */ > + regmap_write(nb7->regmap, GEN_DEV_SET_REG, > + GEN_DEV_SET_CHIP_EN | > + GEN_DEV_SET_CHNA_EN | > + GEN_DEV_SET_CHNB_EN | > + GEN_DEV_SET_CHNC_EN | > + GEN_DEV_SET_CHND_EN | > + FIELD_PREP(GEN_DEV_SET_OP_MODE_MASK, > + GEN_DEV_SET_OP_MODE_DP_4LANE)); > + nb7vpq904m_set_channel(nb7, NB7_CHNA, true); > + nb7vpq904m_set_channel(nb7, NB7_CHNB, true); > + nb7vpq904m_set_channel(nb7, NB7_CHNC, true); > + nb7vpq904m_set_channel(nb7, NB7_CHND, true); > + break; > + > + case TYPEC_DP_STATE_D: > + case TYPEC_DP_STATE_F: > + regmap_write(nb7->regmap, GEN_DEV_SET_REG, > + GEN_DEV_SET_CHIP_EN | > + GEN_DEV_SET_CHNA_EN | > + GEN_DEV_SET_CHNB_EN | > + GEN_DEV_SET_CHNC_EN | > + GEN_DEV_SET_CHND_EN | > + FIELD_PREP(GEN_DEV_SET_OP_MODE_MASK, > + reverse ^ nb7->swap_data_lanes ? > + GEN_DEV_SET_OP_MODE_DP_CC2 > + : GEN_DEV_SET_OP_MODE_DP_CC1)); > + > + /* > + * Normal Orientation (CC1) > + * A -> USB RX > + * B -> USB TX > + * C -> DP1 > + * D -> DP0 > + * Flipped Orientation (CC2) > + * A -> DP0 > + * B -> DP1 > + * C -> USB TX > + * D -> USB RX > + * > + * Reversed if data lanes are swapped > + */ > + if (nb7->swap_data_lanes) { > + nb7vpq904m_set_channel(nb7, NB7_CHNA, !reverse); > + nb7vpq904m_set_channel(nb7, NB7_CHNB, !reverse); > + nb7vpq904m_set_channel(nb7, NB7_CHNC, reverse); > + nb7vpq904m_set_channel(nb7, NB7_CHND, reverse); > + } else { > + nb7vpq904m_set_channel(nb7, NB7_CHNA, reverse); > + nb7vpq904m_set_channel(nb7, NB7_CHNB, reverse); > + nb7vpq904m_set_channel(nb7, NB7_CHNC, !reverse); > + nb7vpq904m_set_channel(nb7, NB7_CHND, !reverse); > + } > + break; > + > + default: > + return -EOPNOTSUPP; > + } > + > + return 0; > +} > + > +static int nb7vpq904m_sw_set(struct typec_switch_dev *sw, enum typec_orientation orientation) > +{ > + struct nb7vpq904m *nb7 = typec_switch_get_drvdata(sw); > + int ret; > + > + ret = typec_switch_set(nb7->typec_switch, orientation); > + if (ret) > + return ret; > + > + mutex_lock(&nb7->lock); > + > + if (nb7->orientation != orientation) { > + nb7->orientation = orientation; > + > + ret = nb7vpq904m_set(nb7); > + } > + > + mutex_unlock(&nb7->lock); > + > + return ret; > +} > + > +static int nb7vpq904m_retimer_set(struct typec_retimer *retimer, struct typec_retimer_state *state) > +{ > + struct nb7vpq904m *nb7 = typec_retimer_get_drvdata(retimer); > + int ret = 0; > + > + mutex_lock(&nb7->lock); > + > + if (nb7->mode != state->mode) { > + nb7->mode = state->mode; > + > + if (state->alt) > + nb7->svid = state->alt->svid; > + else > + nb7->svid = 0; // No SVID > + > + ret = nb7vpq904m_set(nb7); > + } > + > + mutex_unlock(&nb7->lock); > + > + return ret; > +} > + > +#if IS_ENABLED(CONFIG_DRM) > +static int nb7vpq904m_bridge_attach(struct drm_bridge *bridge, > + enum drm_bridge_attach_flags flags) > +{ > + struct nb7vpq904m *nb7 = container_of(bridge, struct nb7vpq904m, bridge); > + struct drm_bridge *next_bridge; > + > + if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) > + return -EINVAL; > + > + next_bridge = devm_drm_of_get_bridge(&nb7->client->dev, nb7->client->dev.of_node, 0, 0); > + if (IS_ERR(next_bridge)) { > + dev_err(&nb7->client->dev, "failed to acquire drm_bridge: %pe\n", next_bridge); > + return PTR_ERR(next_bridge); > + } > + > + return drm_bridge_attach(bridge->encoder, next_bridge, bridge, > + DRM_BRIDGE_ATTACH_NO_CONNECTOR); > +} > + > +static const struct drm_bridge_funcs nb7vpq904m_bridge_funcs = { > + .attach = nb7vpq904m_bridge_attach, > +}; > + > +static int nb7vpq904m_register_bridge(struct nb7vpq904m *nb7) > +{ > + nb7->bridge.funcs = &nb7vpq904m_bridge_funcs; > + nb7->bridge.of_node = nb7->client->dev.of_node; > + > + return devm_drm_bridge_add(&nb7->client->dev, &nb7->bridge); > +} > +#else > +static int nb7vpq904m_register_bridge(struct nb7vpq904m *nb7) > +{ > + return 0; > +} > +#endif > + > +static const struct regmap_config nb7_regmap = { > + .max_register = 0x1f, > + .reg_bits = 8, > + .val_bits = 8, > +}; > + > +enum { > + NORMAL_LANE_MAPPING, > + INVERT_LANE_MAPPING, > +}; > + > +#define DATA_LANES_COUNT 4 > + > +static const int supported_data_lane_mapping[][DATA_LANES_COUNT] = { > + [NORMAL_LANE_MAPPING] = { 0, 1, 2, 3 }, > + [INVERT_LANE_MAPPING] = { 3, 2, 1, 0 }, > +}; > + > +static int nb7vpq904m_parse_data_lanes_mapping(struct nb7vpq904m *nb7) > +{ > + struct device_node *ep; > + u32 data_lanes[4]; > + int ret, i, j; > + > + ep = of_graph_get_endpoint_by_regs(nb7->client->dev.of_node, 1, 0); > + > + if (ep) { > + ret = of_property_count_u32_elems(ep, "data-lanes"); > + if (ret == -EINVAL) > + /* Property isn't here, consider default mapping */ > + goto out_done; > + if (ret < 0) > + goto out_error; > + > + if (ret != DATA_LANES_COUNT) { > + dev_err(&nb7->client->dev, "expected 4 data lanes\n"); > + ret = -EINVAL; > + goto out_error; > + } > + > + ret = of_property_read_u32_array(ep, "data-lanes", data_lanes, DATA_LANES_COUNT); > + if (ret) > + goto out_error; > + > + for (i = 0; i < ARRAY_SIZE(supported_data_lane_mapping); i++) { > + for (j = 0; j < DATA_LANES_COUNT; j++) { > + if (data_lanes[j] != supported_data_lane_mapping[i][j]) > + break; > + } > + > + if (j == DATA_LANES_COUNT) > + break; > + } > + > + switch (i) { > + case NORMAL_LANE_MAPPING: > + break; > + case INVERT_LANE_MAPPING: > + nb7->swap_data_lanes = true; > + dev_info(&nb7->client->dev, "using inverted data lanes mapping\n"); > + break; > + default: > + dev_err(&nb7->client->dev, "invalid data lanes mapping\n"); > + ret = -EINVAL; > + goto out_error; > + } > + } > + > +out_done: > + ret = 0; > + > +out_error: > + of_node_put(ep); > + > + return ret; > +} > + > +static int nb7vpq904m_probe(struct i2c_client *client) > +{ > + struct device *dev = &client->dev; > + struct typec_switch_desc sw_desc = { }; > + struct typec_retimer_desc retimer_desc = { }; > + struct nb7vpq904m *nb7; > + int ret; > + > + nb7 = devm_kzalloc(dev, sizeof(*nb7), GFP_KERNEL); > + if (!nb7) > + return -ENOMEM; > + > + nb7->client = client; > + > + nb7->regmap = devm_regmap_init_i2c(client, &nb7_regmap); > + if (IS_ERR(nb7->regmap)) { > + dev_err(&client->dev, "Failed to allocate register map\n"); > + return PTR_ERR(nb7->regmap); > + } > + > + nb7->mode = TYPEC_STATE_SAFE; > + nb7->orientation = TYPEC_ORIENTATION_NONE; > + > + mutex_init(&nb7->lock); > + > + nb7->enable_gpio = devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW); > + if (IS_ERR(nb7->enable_gpio)) > + return dev_err_probe(dev, PTR_ERR(nb7->enable_gpio), > + "unable to acquire enable gpio\n"); > + > + nb7->vcc_supply = devm_regulator_get_optional(dev, "vcc"); > + if (IS_ERR(nb7->vcc_supply)) > + return PTR_ERR(nb7->vcc_supply); > + > + nb7->typec_switch = fwnode_typec_switch_get(dev->fwnode); > + if (IS_ERR(nb7->typec_switch)) > + return dev_err_probe(dev, PTR_ERR(nb7->typec_switch), > + "failed to acquire orientation-switch\n"); > + > + ret = nb7vpq904m_parse_data_lanes_mapping(nb7); > + if (ret) > + return ret; > + > + ret = regulator_enable(nb7->vcc_supply); > + if (ret) > + dev_warn(dev, "Failed to enable vcc: %d\n", ret); > + > + gpiod_set_value(nb7->enable_gpio, 1); > + > + ret = nb7vpq904m_register_bridge(nb7); > + if (ret) > + return ret; > + > + sw_desc.drvdata = nb7; > + sw_desc.fwnode = dev->fwnode; > + sw_desc.set = nb7vpq904m_sw_set; > + > + nb7->sw = typec_switch_register(dev, &sw_desc); > + if (IS_ERR(nb7->sw)) > + return dev_err_probe(dev, PTR_ERR(nb7->sw), > + "Error registering typec switch\n"); > + > + retimer_desc.drvdata = nb7; > + retimer_desc.fwnode = dev->fwnode; > + retimer_desc.set = nb7vpq904m_retimer_set; > + > + nb7->retimer = typec_retimer_register(dev, &retimer_desc); > + if (IS_ERR(nb7->retimer)) { > + typec_switch_unregister(nb7->sw); > + return dev_err_probe(dev, PTR_ERR(nb7->retimer), > + "Error registering typec retimer\n"); > + } > + > + return 0; > +} > + > +static void nb7vpq904m_remove(struct i2c_client *client) > +{ > + struct nb7vpq904m *nb7 = i2c_get_clientdata(client); > + > + typec_retimer_unregister(nb7->retimer); > + typec_switch_unregister(nb7->sw); > + > + gpiod_set_value(nb7->enable_gpio, 0); > + > + regulator_disable(nb7->vcc_supply); > +} > + > +static const struct i2c_device_id nb7vpq904m_table[] = { > + { "nb7vpq904m" }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, nb7vpq904m_table); > + > +static const struct of_device_id nb7vpq904m_of_table[] = { > + { .compatible = "onnn,nb7vpq904m" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, nb7vpq904m_of_table); > + > +static struct i2c_driver nb7vpq904m_driver = { > + .driver = { > + .name = "nb7vpq904m", > + .of_match_table = nb7vpq904m_of_table, > + }, > + .probe_new = nb7vpq904m_probe, > + .remove = nb7vpq904m_remove, > + .id_table = nb7vpq904m_table, > +}; > + > +module_i2c_driver(nb7vpq904m_driver); > + > +MODULE_AUTHOR("Dmitry Baryshkov <dmitry.baryshkov@linaro.org>"); > +MODULE_DESCRIPTION("OnSemi NB7VPQ904M Type-C driver"); > +MODULE_LICENSE("GPL"); > > -- > 2.34.1 -- heikki ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3 2/2] usb: typec: add support for the nb7vpq904m Type-C Linear Redriver 2023-06-13 14:50 ` [PATCH v3 2/2] usb: typec: add support for the nb7vpq904m Type-C Linear Redriver neil.armstrong 2023-06-14 11:38 ` Heikki Krogerus @ 2023-06-15 9:47 ` Greg Kroah-Hartman 2023-06-15 10:12 ` neil.armstrong 1 sibling, 1 reply; 7+ messages in thread From: Greg Kroah-Hartman @ 2023-06-15 9:47 UTC (permalink / raw) To: neil.armstrong Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Bjorn Andersson, Heikki Krogerus, Liam Girdwood, Mark Brown, Dmitry Baryshkov, linux-arm-msm, linux-usb, devicetree, linux-kernel On Tue, Jun 13, 2023 at 04:50:08PM +0200, neil.armstrong@linaro.org wrote: > From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > > Add support for the ON Semiconductor NB7VPQ904M Type-C USB SuperSpeed > and DisplayPort ALT Mode Linear Redriver chip found on some devices > with a Type-C port. > > The redriver compensates ultra High-Speeed DisplayPort and USB > Super Speed signal integrity losses mainly due to PCB & transmission > cables. > > The redriver doesn't support SuperSpeed lines swapping, but > can support Type-C SBU lines swapping. > > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> > --- > drivers/usb/typec/mux/Kconfig | 8 + > drivers/usb/typec/mux/Makefile | 1 + > drivers/usb/typec/mux/nb7vpq904m.c | 529 +++++++++++++++++++++++++++++++++++++ > 3 files changed, 538 insertions(+) I get the following build error on my system with this applied: CC [M] drivers/usb/typec/mux/nb7vpq904m.o drivers/usb/typec/mux/nb7vpq904m.c: In function ‘nb7vpq904m_register_bridge’: drivers/usb/typec/mux/nb7vpq904m.c:327:20: error: ‘struct drm_bridge’ has no member named ‘of_node’ 327 | nb7->bridge.of_node = nb7->client->dev.of_node; | ^ What went wrong? thanks, greg k-h ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3 2/2] usb: typec: add support for the nb7vpq904m Type-C Linear Redriver 2023-06-15 9:47 ` Greg Kroah-Hartman @ 2023-06-15 10:12 ` neil.armstrong 0 siblings, 0 replies; 7+ messages in thread From: neil.armstrong @ 2023-06-15 10:12 UTC (permalink / raw) To: Greg Kroah-Hartman Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Bjorn Andersson, Heikki Krogerus, Liam Girdwood, Mark Brown, Dmitry Baryshkov, linux-arm-msm, linux-usb, devicetree, linux-kernel On 15/06/2023 11:47, Greg Kroah-Hartman wrote: > On Tue, Jun 13, 2023 at 04:50:08PM +0200, neil.armstrong@linaro.org wrote: >> From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> >> >> Add support for the ON Semiconductor NB7VPQ904M Type-C USB SuperSpeed >> and DisplayPort ALT Mode Linear Redriver chip found on some devices >> with a Type-C port. >> >> The redriver compensates ultra High-Speeed DisplayPort and USB >> Super Speed signal integrity losses mainly due to PCB & transmission >> cables. >> >> The redriver doesn't support SuperSpeed lines swapping, but >> can support Type-C SBU lines swapping. >> >> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> >> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> >> --- >> drivers/usb/typec/mux/Kconfig | 8 + >> drivers/usb/typec/mux/Makefile | 1 + >> drivers/usb/typec/mux/nb7vpq904m.c | 529 +++++++++++++++++++++++++++++++++++++ >> 3 files changed, 538 insertions(+) > > I get the following build error on my system with this applied: > > CC [M] drivers/usb/typec/mux/nb7vpq904m.o > drivers/usb/typec/mux/nb7vpq904m.c: In function ‘nb7vpq904m_register_bridge’: > drivers/usb/typec/mux/nb7vpq904m.c:327:20: error: ‘struct drm_bridge’ has no member named ‘of_node’ > 327 | nb7->bridge.of_node = nb7->client->dev.of_node; > | ^ > > > What went wrong? DRM bridge attach should be protected by #ifdef CONFIG_OF aswell, I'll send a v4 with such fix. Thanks for the report, Neil > > thanks, > > greg k-h ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2023-06-15 10:12 UTC | newest] Thread overview: 7+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2023-06-13 14:50 [PATCH v3 0/2] typec: add support for the ON Semiconductor nb7vpq904m Type-C Linear Redriver Neil Armstrong 2023-06-13 14:50 ` [PATCH v3 1/2] dt-bindings: usb: add ON Semiconductor nb7vpq904m Type-C Linear Redriver bindings Neil Armstrong 2023-06-13 18:23 ` Krzysztof Kozlowski 2023-06-13 14:50 ` [PATCH v3 2/2] usb: typec: add support for the nb7vpq904m Type-C Linear Redriver neil.armstrong 2023-06-14 11:38 ` Heikki Krogerus 2023-06-15 9:47 ` Greg Kroah-Hartman 2023-06-15 10:12 ` neil.armstrong
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).