devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Bhupesh Sharma <bhupesh.sharma@linaro.org>
To: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-usb@vger.kernel.org
Cc: agross@kernel.org, andersson@kernel.org,
	konrad.dybcio@linaro.org, linux-kernel@vger.kernel.org,
	bhupesh.linux@gmail.com, bhupesh.sharma@linaro.org,
	robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org,
	krzysztof.kozlowski@linaro.org, quic_schowdhu@quicinc.com,
	gregkh@linuxfoundation.org, stephan@gerhold.net
Subject: [PATCH v9 4/7] usb: misc: eud: Add driver support for SM6115 / SM4250
Date: Tue, 18 Jul 2023 11:40:49 +0530	[thread overview]
Message-ID: <20230718061052.1332993-5-bhupesh.sharma@linaro.org> (raw)
In-Reply-To: <20230718061052.1332993-1-bhupesh.sharma@linaro.org>

Add SM6115 / SM4250 SoC EUD support in qcom_eud driver.

On some SoCs (like the SM6115 / SM4250 SoC), the mode manager
needs to be accessed only via the secure world (through 'scm'
calls).

Also, the enable bit inside 'tcsr_check_reg' needs to be set
first to set the eud in 'enable' mode on these SoCs.

Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
---
 drivers/usb/misc/Kconfig    |  2 +-
 drivers/usb/misc/qcom_eud.c | 76 ++++++++++++++++++++++++++++++++++---
 2 files changed, 72 insertions(+), 6 deletions(-)

diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig
index 99b15b77dfd57..51eb5140caa14 100644
--- a/drivers/usb/misc/Kconfig
+++ b/drivers/usb/misc/Kconfig
@@ -146,7 +146,7 @@ config USB_APPLEDISPLAY
 
 config USB_QCOM_EUD
 	tristate "QCOM Embedded USB Debugger(EUD) Driver"
-	depends on ARCH_QCOM || COMPILE_TEST
+	depends on (ARCH_QCOM && QCOM_SCM) || COMPILE_TEST
 	select USB_ROLE_SWITCH
 	help
 	  This module enables support for Qualcomm Technologies, Inc.
diff --git a/drivers/usb/misc/qcom_eud.c b/drivers/usb/misc/qcom_eud.c
index 7f371ea1248c3..a5b28fc24116a 100644
--- a/drivers/usb/misc/qcom_eud.c
+++ b/drivers/usb/misc/qcom_eud.c
@@ -11,9 +11,12 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/sysfs.h>
+#include <linux/firmware/qcom/qcom_scm.h>
 #include <linux/usb/role.h>
 
 #define EUD_REG_INT1_EN_MASK	0x0024
@@ -30,6 +33,10 @@
 #define EUD_INT_SAFE_MODE	BIT(4)
 #define EUD_INT_ALL		(EUD_INT_VBUS | EUD_INT_SAFE_MODE)
 
+#define EUD_EN2_EN		BIT(0)
+#define EUD_EN2_DISABLE		(0)
+#define TCSR_CHECK_EN		BIT(0)
+
 struct eud_chip {
 	struct device			*dev;
 	struct usb_role_switch		*role_sw;
@@ -39,6 +46,7 @@ struct eud_chip {
 	int				irq;
 	bool				enabled;
 	bool				usb_attached;
+	phys_addr_t			secure_mode_mgr;
 };
 
 static int enable_eud(struct eud_chip *priv)
@@ -46,7 +54,11 @@ static int enable_eud(struct eud_chip *priv)
 	writel(EUD_ENABLE, priv->base + EUD_REG_CSR_EUD_EN);
 	writel(EUD_INT_VBUS | EUD_INT_SAFE_MODE,
 			priv->base + EUD_REG_INT1_EN_MASK);
-	writel(1, priv->mode_mgr + EUD_REG_EUD_EN2);
+
+	if (priv->secure_mode_mgr)
+		qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_EN);
+	else
+		writel(EUD_EN2_EN, priv->mode_mgr + EUD_REG_EUD_EN2);
 
 	return usb_role_switch_set_role(priv->role_sw, USB_ROLE_DEVICE);
 }
@@ -54,7 +66,11 @@ static int enable_eud(struct eud_chip *priv)
 static void disable_eud(struct eud_chip *priv)
 {
 	writel(0, priv->base + EUD_REG_CSR_EUD_EN);
-	writel(0, priv->mode_mgr + EUD_REG_EUD_EN2);
+
+	if (priv->secure_mode_mgr)
+		qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_DISABLE);
+	else
+		writel(EUD_EN2_DISABLE, priv->mode_mgr + EUD_REG_EUD_EN2);
 }
 
 static ssize_t enable_show(struct device *dev,
@@ -175,9 +191,37 @@ static void eud_role_switch_release(void *data)
 	usb_role_switch_put(chip->role_sw);
 }
 
+static int eud_find_secure_reg_addr(struct device *dev, u64 *addr)
+{
+	struct device_node *tcsr;
+	struct device_node *np = dev->of_node;
+	struct resource res;
+	u32 offset;
+	int ret;
+
+	tcsr = of_parse_phandle(np, "qcom,secure-eud-reg", 0);
+	if (!tcsr)
+		return 0;
+
+	ret = of_address_to_resource(tcsr, 0, &res);
+	of_node_put(tcsr);
+	if (ret)
+		return ret;
+
+	ret = of_property_read_u32_index(np, "qcom,secure-eud-reg", 1, &offset);
+	if (ret < 0)
+		return ret;
+
+	*addr = res.start + offset;
+
+	return 0;
+}
+
 static int eud_probe(struct platform_device *pdev)
 {
 	struct eud_chip *chip;
+	struct resource *res;
+	phys_addr_t tcsr_check = 0;
 	int ret;
 
 	chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL);
@@ -200,9 +244,30 @@ static int eud_probe(struct platform_device *pdev)
 	if (IS_ERR(chip->base))
 		return PTR_ERR(chip->base);
 
-	chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1);
-	if (IS_ERR(chip->mode_mgr))
-		return PTR_ERR(chip->mode_mgr);
+	/*
+	 * EUD block on a few Qualcomm SoCs needs secure register access.
+	 * Check for the same via vendor-specific dt property.
+	 */
+	ret = eud_find_secure_reg_addr(&pdev->dev, &tcsr_check);
+	if (ret < 0)
+		return ret;
+
+	if (tcsr_check) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+		if (!res)
+			return dev_err_probe(chip->dev, -ENODEV,
+					     "failed to get secure_mode_mgr reg base\n");
+
+		chip->secure_mode_mgr = res->start;
+
+		ret = qcom_scm_io_writel(tcsr_check, TCSR_CHECK_EN);
+		if (ret)
+			return dev_err_probe(chip->dev, ret, "failed to write tcsr check reg\n");
+	} else {
+		chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1);
+		if (IS_ERR(chip->mode_mgr))
+			return PTR_ERR(chip->mode_mgr);
+	}
 
 	chip->irq = platform_get_irq(pdev, 0);
 	ret = devm_request_threaded_irq(&pdev->dev, chip->irq, handle_eud_irq,
@@ -230,6 +295,7 @@ static void eud_remove(struct platform_device *pdev)
 
 static const struct of_device_id eud_dt_match[] = {
 	{ .compatible = "qcom,sc7280-eud" },
+	{ .compatible = "qcom,sm6115-eud" },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, eud_dt_match);
-- 
2.38.1


  parent reply	other threads:[~2023-07-18  6:12 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-07-18  6:10 [PATCH v9 0/7] Add Qualcomm SM6115 / SM4250 EUD dt-bindings & driver support Bhupesh Sharma
2023-07-18  6:10 ` [PATCH v9 1/7] dt-bindings: mfd: qcom,tcsr: Add the compatible for SM6115 Bhupesh Sharma
2023-07-18  6:22   ` Krzysztof Kozlowski
2023-07-18  6:10 ` [PATCH v9 2/7] dt-bindings: soc: qcom: eud: Document vendor-specific 'secure mode' property Bhupesh Sharma
2023-07-18  6:26   ` Krzysztof Kozlowski
2023-07-18  6:10 ` [PATCH v9 3/7] dt-bindings: soc: qcom: eud: Add SM6115 / SM4250 support Bhupesh Sharma
2023-07-18  6:10 ` Bhupesh Sharma [this message]
2023-07-18  6:31   ` [PATCH v9 4/7] usb: misc: eud: Add driver support for SM6115 / SM4250 Krzysztof Kozlowski
2023-07-18  7:51   ` Souradeep Chowdhury
2023-07-19  2:46   ` kernel test robot
2023-07-18  6:10 ` [PATCH v9 5/7] arm64: dts: qcom: sm6115: Add tcsr syscon node Bhupesh Sharma
2023-07-26 15:57   ` Konrad Dybcio
2023-07-18  6:10 ` [PATCH v9 6/7] arm64: dts: qcom: sm6115: Add EUD dt node and dwc3 connector Bhupesh Sharma
2023-07-18  6:10 ` [PATCH v9 7/7] arm64: dts: qcom: qrb4210-rb2: Enable EUD debug peripheral Bhupesh Sharma

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230718061052.1332993-5-bhupesh.sharma@linaro.org \
    --to=bhupesh.sharma@linaro.org \
    --cc=agross@kernel.org \
    --cc=andersson@kernel.org \
    --cc=bhupesh.linux@gmail.com \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=konrad.dybcio@linaro.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=krzysztof.kozlowski@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=quic_schowdhu@quicinc.com \
    --cc=robh+dt@kernel.org \
    --cc=stephan@gerhold.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).