[PATCH v9 6/7] arm64: dts: qcom: sm6115: Add EUD dt node and dwc3 connector

[Bhupesh Sharma <bhupesh.sharma@linaro.org>]

Add the Embedded USB Debugger(EUD) device tree node for
SM6115 / SM4250 SoC.

The node contains EUD base register region, EUD mode manager
register region.

The TCSR Base register region is defined via a vendor specific
dt-property.

Also add the typec connector node for EUD which is attached to
EUD node via port. EUD is also attached to DWC3 node via port.

To enable the role switch, we need to set dr_mode = "otg" property
for 'usb_dwc3' sub-node in the board dts file.

Also the EUD device can be enabled on a board once linux is boot'ed
by setting:
 $ echo 1 > /sys/bus/platform/drivers/qcom_eud/../enable

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm6115.dtsi | 51 ++++++++++++++++++++++++++++
 1 file changed, 51 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
index 3be0b54fc3628..cd5b85b63a9ec 100644
--- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
@@ -260,6 +260,18 @@ CLUSTER_1_SLEEP_1: cluster-sleep-1-1 {
 		};
 	};
 
+	eud_typec: connector {
+		compatible = "usb-c-connector";
+
+		ports {
+			port@0 {
+				con_eud: endpoint {
+					remote-endpoint = <&eud_con>;
+				};
+			};
+		};
+	};
+
 	firmware {
 		scm: scm {
 			compatible = "qcom,scm-sm6115", "qcom,scm";
@@ -794,6 +806,38 @@ gcc: clock-controller@1400000 {
 			#power-domain-cells = <1>;
 		};
 
+		eud: eud@1610000 {
+			compatible = "qcom,sm6115-eud", "qcom,eud";
+			reg = <0x0 0x01610000 0x0 0x2000>,
+			      <0x0 0x01612000 0x0 0x1000>;
+			reg-names = "eud-base", "eud-mode-mgr";
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
+
+			qcom,secure-eud-reg = <&tcsr_regs 0x25018>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					eud_ep: endpoint {
+						remote-endpoint = <&usb2_role_switch>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					eud_con: endpoint {
+						remote-endpoint = <&con_eud>;
+					};
+				};
+			};
+		};
+
 		usb_hsphy: phy@1613000 {
 			compatible = "qcom,sm6115-qusb2-phy";
 			reg = <0x0 0x01613000 0x0 0x180>;
@@ -1327,6 +1371,13 @@ usb_dwc3: usb@4e00000 {
 				snps,has-lpm-erratum;
 				snps,hird-threshold = /bits/ 8 <0x10>;
 				snps,usb3_lpm_capable;
+				usb-role-switch;
+
+				port {
+					usb2_role_switch: endpoint {
+						remote-endpoint = <&eud_ep>;
+					};
+				};
 			};
 		};
 
-- 
2.38.1