From: Alexander Stein <alexander.stein@ew.tq-group.com>
To: Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Shawn Guo <shawnguo@kernel.org>, Li Yang <leoyang.li@nxp.com>,
Markus Niebel <Markus.Niebel@ew.tq-group.com>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: [PATCH v5 2/3] ARM: dts: ls1021a: add TQ-Systems MBLS102xA device tree
Date: Mon, 31 Jul 2023 11:23:30 +0200 [thread overview]
Message-ID: <20230731092331.358427-3-alexander.stein@ew.tq-group.com> (raw)
In-Reply-To: <20230731092331.358427-1-alexander.stein@ew.tq-group.com>
Add device tree for the MBLS102xA mainboard with TQMLS1021A SoM.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
arch/arm/boot/dts/nxp/ls/Makefile | 1 +
.../nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts | 405 ++++++++++++++++++
.../boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi | 76 ++++
3 files changed, 482 insertions(+)
create mode 100644 arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts
create mode 100644 arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi
diff --git a/arch/arm/boot/dts/nxp/ls/Makefile b/arch/arm/boot/dts/nxp/ls/Makefile
index 3cb1d516f6fb..14759331dba2 100644
--- a/arch/arm/boot/dts/nxp/ls/Makefile
+++ b/arch/arm/boot/dts/nxp/ls/Makefile
@@ -3,5 +3,6 @@ dtb-$(CONFIG_SOC_LS1021A) += \
ls1021a-iot.dtb \
ls1021a-moxa-uc-8410a.dtb \
ls1021a-qds.dtb \
+ ls1021a-tqmls1021a-mbls1021a.dtb \
ls1021a-tsn.dtb \
ls1021a-twr.dtb
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts
new file mode 100644
index 000000000000..34636fcdfd6a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts
@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+#include "ls1021a-tqmls1021a.dtsi"
+
+/ {
+ model = "TQMLS102xA SOM on MBLS102xA";
+ compatible = "tq,ls1021a-tqmls1021a-mbls102xa", "tq,ls1021a-tqmls1021a", "fsl,ls1021a";
+
+ audio_mclk: audio-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ backlight_dcu: backlight {
+ compatible = "gpio-backlight";
+ gpios = <&pca9530 0 GPIO_ACTIVE_LOW>;
+ status = "disabled";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ switch-1 {
+ label = "S6";
+ linux,code = <BTN_0>;
+ gpios = <&pca9554_0 0 GPIO_ACTIVE_LOW>;
+ };
+
+ btn2: switch-2 {
+ label = "S7";
+ linux,code = <BTN_1>;
+ gpios = <&pca9554_0 1 GPIO_ACTIVE_LOW>;
+ };
+
+ switch-3 {
+ label = "S8";
+ linux,code = <BTN_2>;
+ gpios = <&pca9554_0 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio_leds: gpio-leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <0>;
+ gpios = <&pca9554_2 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-on";
+ };
+
+ led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <1>;
+ gpios = <&pca9554_2 5 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-on";
+ };
+
+ led-2 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <2>;
+ gpios = <&pca9554_2 6 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-on";
+ };
+
+ led-3 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_HEARTBEAT;
+ function-enumerator = <0>;
+ gpios = <&pca9554_2 7 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ lvds_encoder: lvds-encoder {
+ compatible = "ti,sn75lvds83", "lvds-encoder";
+ power-supply = <®_3p3v>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lvds_encoder_in: endpoint {};
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lvds_encoder_out: endpoint {};
+ };
+ };
+ };
+
+ reg_1p2v: regulator-1p2v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ vin-supply = <®_3p3v>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ hdmi_out: hdmi {
+ compatible = "hdmi-connector";
+ type = "a";
+ ddc-i2c-bus = <&i2c0>;
+ status = "disabled";
+
+ port {
+ hdmi_in: endpoint {
+ remote-endpoint = <&sii9022a_out>;
+ };
+ };
+ };
+
+ display: panel {
+ backlight = <&backlight_dcu>;
+ enable-gpios = <&pca9554_1 3 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+
+ port {
+ panel_in: endpoint {};
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx-audio-tlv320aic32x4";
+ model = "ls1021a-mbls1021a-tlv320aic32";
+ ssi-controller = <&sai1>;
+ audio-codec = <&tlv320aic32x4>;
+ };
+
+};
+
+&can0 {
+ xceiver-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&can1 {
+ xceiver-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&dspi0 {
+ status = "okay";
+};
+
+&enet0 {
+ phy-handle = <&rgmii_phy0c>;
+ phy-mode = "rgmii-id";
+ mac-address = [ 00 00 00 00 00 00 ];
+ status = "okay";
+};
+
+&enet1 {
+ tbi-handle = <&tbi1>;
+ phy-handle = <&sgmii_phy03>;
+ phy-mode = "sgmii";
+ mac-address = [ 00 00 00 00 00 00 ];
+ status = "okay";
+};
+
+&enet2 {
+ phy-handle = <&rgmii_phy04>;
+ phy-mode = "rgmii-id";
+ mac-address = [ 00 00 00 00 00 00 ];
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ tlv320aic32x4: audio-codec@18 {
+ compatible = "ti,tlv320aic32x4";
+ reg = <0x18>;
+ clocks = <&audio_mclk>;
+ clock-names = "mclk";
+ ldoin-supply = <®_3p3v>;
+ iov-supply = <®_3p3v>;
+ };
+
+ pca9554_0: gpio-expander@20 {
+ compatible = "nxp,pca9554";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vcc-supply = <®_3p3v>;
+ gpio-line-names = "BUTTON0", "BUTTON1",
+ "BUTTON2", "EMMC_SEL",
+ "DIP2", "DIP3",
+ "EXT_TOUCH_INT", "GPIO_1";
+ };
+
+ pca9554_1: gpio-expander@21 {
+ compatible = "nxp,pca9554";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vcc-supply = <®_3p3v>;
+ gpio-line-names = "PCIE_PWR_EN", "MPCIE_DISABLE#",
+ "MPCIE_WAKE#", "LCD_BLT_EN",
+ "LCD_PWR_EN", "EC1_PHY_PWDN",
+ "EC3_PHY_PWDN", "SGMII_PHY_PWDN";
+ };
+
+ pca9554_2: gpio-expander@22 {
+ compatible = "nxp,pca9554";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&extirq>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ vcc-supply = <®_3p3v>;
+ gpio-line-names = "MUX_SEL0", "MUX_SEL1",
+ "MUX_SEL2", "MUX_SEL3",
+ "V95", "V96", "V97", "V98";
+ };
+
+ sii9022a: hdmi-transmitter@3b {
+ compatible = "sil,sii9022";
+ reg = <0x3b>;
+ iovcc-supply = <®_3p3v>;
+ cvcc12-supply = <®_1p2v>;
+ interrupts = <GIC_SPI 167 IRQ_TYPE_EDGE_RISING>;
+ #sound-dai-cells = <0>;
+ sil,i2s-data-lanes = <0>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ sii9022a_in: endpoint {};
+ };
+
+ port@1 {
+ reg = <1>;
+
+ sii9022a_out: endpoint {
+ remote-endpoint = <&hdmi_in>;
+ };
+ };
+ };
+ };
+
+ stmpe811: port-expander@41 {
+ compatible = "st,stmpe811";
+ reg = <0x41>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+ vcc-supply = <®_3p3v>;
+ vio-supply = <®_3p3v>;
+
+ gpio {
+ compatible = "st,stmpe-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ /* GPIO 5-7 used for touch */
+ st,norequest-mask = <0xf0>;
+ gpio-line-names = "GPIO_ADC_I2C1_1",
+ "GPIO_ADC_I2C1_2",
+ "GPIO_ADC_I2C1_3",
+ "GPIO_ADC_I2C1_4";
+ };
+
+ touchscreen {
+ compatible = "st,stmpe-ts";
+ status = "disabled";
+ };
+ };
+
+ pca9530: leds@60 {
+ compatible = "nxp,pca9530";
+ reg = <0x60>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "PWM_0", "PWM_1";
+
+ led-0 {
+ type = <PCA9532_TYPE_GPIO>;
+ };
+
+ led-1 {
+ type = <PCA9532_TYPE_GPIO>;
+ };
+ };
+
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&lpuart0 {
+ linux,rs485-enabled-at-boot-time;
+ status = "okay";
+};
+
+&mdio0 {
+ sgmii_phy03: ethernet-phy@3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x03>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+ ti,dp83867-rxctrl-strap-quirk;
+ };
+
+ rgmii_phy04: ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x04>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+ };
+
+ rgmii_phy0c: ethernet-phy@c {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0c>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+ };
+};
+
+&pwm6 {
+ status = "okay";
+};
+
+&pwm7 {
+ status = "okay";
+};
+
+&sai1 {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb3 {
+ /*
+ * Although DR connector, VBUS is always driven, so
+ * restrict to host mode.
+ */
+ dr_mode = "host";
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi
new file mode 100644
index 000000000000..7fd35d124fba
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+#include "ls1021a.dtsi"
+
+/ {
+ model = "TQMLS102xA SOM";
+ compatible = "tq,ls1021a-tqmls1021a", "fsl,ls1021a";
+
+ reg_3p3v_som: regulator-3p3v-som {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V_SOM";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+&esdhc {
+ /* e-MMC over 8 data lines */
+ bus-width = <8>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ /* MC34VR500 DC/DC regulator at 0x8, managed by PMIC */
+ /* On-board PMC at 0x11 */
+
+ sa56004: temperature-sensor@4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <®_3p3v_som>;
+ };
+
+ rtc0: rtc@51 {
+ compatible = "nxp,pcf85063a";
+ reg = <0x51>;
+ quartz-load-femtofarads = <12500>;
+ };
+
+ m24c64_54: eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ pagesize = <32>;
+ read-only;
+ vcc-supply = <®_3p3v_som>;
+ };
+};
+
+&mdio0 {
+ tbi1: tbi-phy@8 {
+ reg = <0x8>;
+ device_type = "tbi-phy";
+ };
+};
+
+&qspi {
+ status = "okay";
+
+ qflash0: flash@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <20000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+ reg = <0>;
+ };
+};
--
2.34.1
next prev parent reply other threads:[~2023-07-31 9:25 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-07-31 9:23 [PATCH v5 0/3] TQMLS1021A support Alexander Stein
2023-07-31 9:23 ` [PATCH v5 1/3] dt-bindings: arm: fsl: add TQ-Systems LS1021A board Alexander Stein
2023-07-31 9:23 ` Alexander Stein [this message]
2023-07-31 9:23 ` [PATCH v5 3/3] ARM: dts: ls1021a: add TQMLS1021A flash partition layout Alexander Stein
2023-08-06 12:21 ` [PATCH v5 0/3] TQMLS1021A support Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230731092331.358427-3-alexander.stein@ew.tq-group.com \
--to=alexander.stein@ew.tq-group.com \
--cc=Markus.Niebel@ew.tq-group.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).