From: Chris Morgan <macroalpha82@gmail.com>
To: linux-sunxi@lists.linux.dev
Cc: devicetree@vger.kernel.org, mripard@kernel.org, jagan@edgeble.ai,
heiko@sntech.de, uwu@icenowy.me, andre.przywara@arm.com,
daniel@ffwll.ch, airlied@gmail.com, sam@ravnborg.org,
neil.armstrong@linaro.org, noralf@tronnes.org,
samuel@sholland.org, jernej.skrabec@gmail.com, wens@csie.org,
conor+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org,
robh+dt@kernel.org, Chris Morgan <macromorgan@hotmail.com>
Subject: [PATCH V3 0/8] Add Anbernic RG-Nano
Date: Wed, 23 Aug 2023 16:25:46 -0500 [thread overview]
Message-ID: <20230823212554.378403-1-macroalpha82@gmail.com> (raw)
From: Chris Morgan <macromorgan@hotmail.com>
Add support for the Anbernic RG-Nano handheld gaming device
Changes since V2:
- Add display support.
- Add USB host support.
- Removed CPU frequency and voltage parameters, as CPU regulator may
be tied into additional areas that need further testing.
- Added regulator names back, as they appear to have been accidentally
dropped in v2.
- Updated notes to denote all hardware tested and working.
Changes since V1:
- Added additional pwm pin configs to sun8i-v3s.dtsi and removed
default config for pwm0 in lieu of defining it for each board.
- Noted in patch notes that additional hardware of UART debug port,
USB port (in gadget mode) also work, and that USB host mode does
not work.
- Identified GPIO responsible for enabling external speaker amplifier
and defined it, allowing onboard audio to work.
- Removed ac_power_supply node.
- Set regulator min and max values to the same value as defined in the
schematics.
- Removed definition for reg_ldo1. This regulator is hardware
configured so the value did not affect anything, however the driver
must be updated to support the correct value of 3.3v in this case.
- Removed usb0_id_det-gpios as I cannot confirm these are correct.
Chris Morgan (8):
dt-bindings: vendor-prefixes: document Saef Technology
dt-bindings: display: panel: mipi-dbi-spi: add Saef SF-TC154B
arm: dts: sun8i: V3s: Add pinctrl for pwm
dt-bindings: usb: Add V3s compatible string for EHCI
dt-bindings: usb: Add V3s compatible string for OHCI
ARM: dts: sun8i: v3s: add EHCI and OHCI to v3s dts
dt-bindings: arm: sunxi: add Anbernic RG-Nano
ARM: dts: sunxi: add support for Anbernic RG-Nano
.../devicetree/bindings/arm/sunxi.yaml | 5 +
.../display/panel/panel-mipi-dbi-spi.yaml | 1 +
.../devicetree/bindings/usb/generic-ehci.yaml | 1 +
.../devicetree/bindings/usb/generic-ohci.yaml | 1 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun8i-v3s-anbernic-rg-nano.dts | 275 ++++++++++++++++++
arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi | 31 ++
8 files changed, 317 insertions(+)
create mode 100644 arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
--
2.34.1
next reply other threads:[~2023-08-23 21:26 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-23 21:25 Chris Morgan [this message]
2023-08-23 21:25 ` [PATCH V3 1/8] dt-bindings: vendor-prefixes: document Saef Technology Chris Morgan
2023-08-24 15:20 ` Conor Dooley
2023-08-23 21:25 ` [PATCH V3 2/8] dt-bindings: display: panel: mipi-dbi-spi: add Saef SF-TC154B Chris Morgan
2023-08-24 15:22 ` Conor Dooley
2023-08-24 20:54 ` Noralf Trønnes
2023-08-23 21:25 ` [PATCH V3 3/8] arm: dts: sun8i: V3s: Add pinctrl for pwm Chris Morgan
2023-08-23 21:25 ` [PATCH V3 4/8] dt-bindings: usb: Add V3s compatible string for EHCI Chris Morgan
2023-08-24 15:21 ` Conor Dooley
2023-08-23 21:25 ` [PATCH V3 5/8] dt-bindings: usb: Add V3s compatible string for OHCI Chris Morgan
2023-08-24 15:19 ` Conor Dooley
2023-08-23 21:25 ` [PATCH V3 6/8] ARM: dts: sun8i: v3s: add EHCI and OHCI to v3s dts Chris Morgan
2023-08-24 21:21 ` Andre Przywara
2023-08-25 15:58 ` Chris Morgan
2023-08-25 21:53 ` Andre Przywara
2023-08-28 15:17 ` Chris Morgan
2023-08-23 21:25 ` [PATCH V3 7/8] dt-bindings: arm: sunxi: add Anbernic RG-Nano Chris Morgan
2023-08-23 21:25 ` [PATCH V3 8/8] ARM: dts: sunxi: add support for " Chris Morgan
2023-08-25 22:37 ` Andre Przywara
2023-08-26 2:13 ` Chris Morgan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230823212554.378403-1-macroalpha82@gmail.com \
--to=macroalpha82@gmail.com \
--cc=airlied@gmail.com \
--cc=andre.przywara@arm.com \
--cc=conor+dt@kernel.org \
--cc=daniel@ffwll.ch \
--cc=devicetree@vger.kernel.org \
--cc=heiko@sntech.de \
--cc=jagan@edgeble.ai \
--cc=jernej.skrabec@gmail.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-sunxi@lists.linux.dev \
--cc=macromorgan@hotmail.com \
--cc=mripard@kernel.org \
--cc=neil.armstrong@linaro.org \
--cc=noralf@tronnes.org \
--cc=robh+dt@kernel.org \
--cc=sam@ravnborg.org \
--cc=samuel@sholland.org \
--cc=uwu@icenowy.me \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).