From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
To: shawnguo@kernel.org, leoyang.li@nxp.com, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org, conor+dt@kernel.org,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Subject: [PATCH v2] arm64: dts: ls208xa: use a pseudo-bus to constrain usb dma size
Date: Thu, 14 Sep 2023 18:59:35 +0300 [thread overview]
Message-ID: <20230914155935.6042-1-laurentiu.tudor@nxp.com> (raw)
Wrap the usb controllers in an intermediate simple-bus and use it to
constrain the dma address size of these usb controllers to the 40b
that they generate toward the interconnect. This is required because
the SoC uses 48b address sizes and this mismatch would lead to smmu
context faults [1] because the usb generates 40b addresses while the
smmu page tables are populated with 48b wide addresses.
[1]
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002000010
xhci-hcd xhci-hcd.0.auto: irq 108, io mem 0x03100000
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xffffffb000, fsynr=0x0, cbfrsynra=0xc01, cb=3
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
Changes in v2:
- renamed pseudo-bus from 'aux_bus' to just 'bus'
.../arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 46 +++++++++++--------
1 file changed, 27 insertions(+), 19 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
index d2f5345d0560..6c311c61c5bc 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -1186,26 +1186,34 @@
dma-coherent;
};
- usb0: usb@3100000 {
- status = "disabled";
- compatible = "snps,dwc3";
- reg = <0x0 0x3100000 0x0 0x10000>;
- interrupts = <0 80 0x4>; /* Level high type */
- dr_mode = "host";
- snps,quirk-frame-length-adjustment = <0x20>;
- snps,dis_rxdet_inp3_quirk;
- snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
- };
+ bus: bus {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+ dma-ranges = <0x0 0x0 0x0 0x0 0x100 0x00000000>;
+
+ usb0: usb@3100000 {
+ status = "disabled";
+ compatible = "snps,dwc3";
+ reg = <0x0 0x3100000 0x0 0x10000>;
+ interrupts = <0 80 0x4>; /* Level high type */
+ dr_mode = "host";
+ snps,quirk-frame-length-adjustment = <0x20>;
+ snps,dis_rxdet_inp3_quirk;
+ snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+ };
- usb1: usb@3110000 {
- status = "disabled";
- compatible = "snps,dwc3";
- reg = <0x0 0x3110000 0x0 0x10000>;
- interrupts = <0 81 0x4>; /* Level high type */
- dr_mode = "host";
- snps,quirk-frame-length-adjustment = <0x20>;
- snps,dis_rxdet_inp3_quirk;
- snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+ usb1: usb@3110000 {
+ status = "disabled";
+ compatible = "snps,dwc3";
+ reg = <0x0 0x3110000 0x0 0x10000>;
+ interrupts = <0 81 0x4>; /* Level high type */
+ dr_mode = "host";
+ snps,quirk-frame-length-adjustment = <0x20>;
+ snps,dis_rxdet_inp3_quirk;
+ snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+ };
};
ccn@4000000 {
--
2.17.1
next reply other threads:[~2023-09-14 15:59 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-09-14 15:59 Laurentiu Tudor [this message]
2023-09-25 2:50 ` [PATCH v2] arm64: dts: ls208xa: use a pseudo-bus to constrain usb dma size Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230914155935.6042-1-laurentiu.tudor@nxp.com \
--to=laurentiu.tudor@nxp.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).