[PATCH V3 1/2] arm:dts: am3517-evm: Fix LED3/4 pinmux

[PATCH V3 1/2] arm:dts: am3517-evm: Fix LED3/4 pinmux

[Adam Ford]

The pinmux for LED3 and LED4 are incorrectly attached to the
omap3_pmx_core when they should be connected to the omap3_pmx_wkup
pin mux.  This was likely masked by the fact that the bootloader
used to do all the pinmuxing.

Fixes: 0dbf99542caf ("ARM: dts: am3517-evm: Add User LEDs and Pushbutton")
Signed-off-by: Adam Ford <aford173@gmail.com>
---
V3:  No Change
V2:  Use current device tree naming convention for led-pins

This likely will require a separate patch to apply to previous file location.

diff --git a/arch/arm/boot/dts/ti/omap/am3517-evm.dts b/arch/arm/boot/dts/ti/omap/am3517-evm.dts
index af9df15274be..866f68c5b504 100644
--- a/arch/arm/boot/dts/ti/omap/am3517-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/am3517-evm.dts
@@ -271,13 +271,6 @@ OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c3_sda */
 		>;
 	};
 
-	leds_pins: leds-pins {
-		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 */
-			OMAP3_WKUP_IOPAD(0x2a26, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu1.gpio_31 */
-		>;
-	};
-
 	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
@@ -355,3 +348,12 @@ OMAP3430_CORE2_IOPAD(0x25e2, PIN_INPUT | MUX_MODE3)	/* etk_d3.hsusb1_data7 */
 		>;
 	};
 };
+
+&omap3_pmx_wkup {
+	leds_pins: leds-pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 */
+			OMAP3_WKUP_IOPAD(0x2a26, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu1.gpio_31 */
+		>;
+	};
+};
-- 
2.40.1

[PATCH V3 2/2] arm: dts: am3517-evm: Enable Ethernet PHY Interrupt

[Adam Ford]

The Ethernet PHY interrupt pin is routed to GPIO_58.  Create a
PHY node to configure this GPIO for the interrupt to avoid polling.

Signed-off-by: Adam Ford <aford173@gmail.com>
---
V3:  Fix issue where V2 wasn't properly properly commit-ammended, so V2 patch didn't properly generate

V2:  Attempted (but failed) to fix ethernet-phy-pins naming

diff --git a/arch/arm/boot/dts/ti/omap/am3517-evm.dts b/arch/arm/boot/dts/ti/omap/am3517-evm.dts
index 866f68c5b504..40f15da81043 100644
--- a/arch/arm/boot/dts/ti/omap/am3517-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/am3517-evm.dts
@@ -172,11 +172,24 @@ hsusb1_phy: hsusb1_phy {
 &davinci_emac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
 	status = "okay";
 };
 
 &davinci_mdio {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&enet_phy_pins>;
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;	/* gpio_58 */
+	};
 };
 
 &dss {
@@ -257,6 +270,12 @@ OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50mhz_clk */
 		>;
 	};
 
+	enet_phy_pins: ethernet-phy-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20bc, PIN_INPUT | MUX_MODE4)	/* gpmc_ncs7.gpio_57 */
+		>;
+	};
+
 	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c2_scl */
-- 
2.40.1

Re: [PATCH V3 2/2] arm: dts: am3517-evm: Enable Ethernet PHY Interrupt

[Tony Lindgren]

* Adam Ford <aford173@gmail.com> [231005 00:04]:
> The Ethernet PHY interrupt pin is routed to GPIO_58.  Create a
> PHY node to configure this GPIO for the interrupt to avoid polling.

Thanks applying both into omap-for-v6.7/dt.

Tony