* [PATCH 0/2] Add eMMC support for AM62a SK @ 2023-10-27 9:39 Nitin Yadav 2023-10-27 9:39 ` [PATCH 1/2] arm64: dts: ti: k3-am62a-main: Add sdhci0 instance Nitin Yadav 2023-10-27 9:39 ` [PATCH 2/2] arm64: dts: ti: k3-am62a7-sk: Enable eMMC support Nitin Yadav 0 siblings, 2 replies; 5+ messages in thread From: Nitin Yadav @ 2023-10-27 9:39 UTC (permalink / raw) To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt Cc: linux-arm-kernel, devicetree, linux-kernel This series enables eMMC support on AM62a SK. Nitin Yadav (2): arm64: dts: ti: k3-am62a-main: Add sdhci0 instance arm64: dts: ti: k3-am62a7-sk: Enable eMMC support arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 19 +++++++++++++++++ arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 25 +++++++++++++++++++++++ 2 files changed, 44 insertions(+) -- 2.25.1 ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/2] arm64: dts: ti: k3-am62a-main: Add sdhci0 instance 2023-10-27 9:39 [PATCH 0/2] Add eMMC support for AM62a SK Nitin Yadav @ 2023-10-27 9:39 ` Nitin Yadav 2023-10-27 11:22 ` Nishanth Menon 2023-10-27 9:39 ` [PATCH 2/2] arm64: dts: ti: k3-am62a7-sk: Enable eMMC support Nitin Yadav 1 sibling, 1 reply; 5+ messages in thread From: Nitin Yadav @ 2023-10-27 9:39 UTC (permalink / raw) To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt Cc: linux-arm-kernel, devicetree, linux-kernel Add sdhci0 DT node in k3-am62a-main for eMMC support. Droping ITAP values as they are NA in datasheet[0] for lower speed modes. Add mmc0 alias for sdhci0 in k3-am62a7-sk.dts. [0]https://www.ti.com/lit/gpn/am62a3 Table: 7-79 (Page No. 179) Signed-off-by: Nitin Yadav <n-yadav@ti.com> --- arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 19 +++++++++++++++++++ arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 1 + 2 files changed, 20 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi index de36abb243f1..89b8b7d302cd 100644 --- a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi @@ -488,6 +488,25 @@ main_gpio1: gpio@601000 { status = "disabled"; }; + sdhci0: mmc@fa10000 { + compatible = "ti,am62-sdhci"; + reg = <0x00 0xfa10000 0x00 0x260>, <0x00 0xfa18000 0x00 0x134>; + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 57 5>, <&k3_clks 57 6>; + clock-names = "clk_ahb", "clk_xin"; + assigned-clocks = <&k3_clks 57 6>; + assigned-clock-parents = <&k3_clks 57 8>; + mmc-hs200-1_8v; + ti,trm-icp = <0x2>; + ti,otap-del-sel-legacy = <0x0>; + ti,otap-del-sel-mmc-hs = <0x0>; + ti,otap-del-sel-hs200 = <0x6>; + bus-width = <8>; + ti,clkbuf-sel = <0x7>; + status = "disabled"; + }; + sdhci1: mmc@fa00000 { compatible = "ti,am62-sdhci"; reg = <0x00 0xfa00000 0x00 0x260>, <0x00 0xfa08000 0x00 0x134>; diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts index cff283c75f8e..5d28c390b28e 100644 --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts @@ -20,6 +20,7 @@ aliases { serial0 = &wkup_uart0; serial2 = &main_uart0; serial3 = &main_uart1; + mmc0 = &sdhci0; mmc1 = &sdhci1; }; -- 2.25.1 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 1/2] arm64: dts: ti: k3-am62a-main: Add sdhci0 instance 2023-10-27 9:39 ` [PATCH 1/2] arm64: dts: ti: k3-am62a-main: Add sdhci0 instance Nitin Yadav @ 2023-10-27 11:22 ` Nishanth Menon 0 siblings, 0 replies; 5+ messages in thread From: Nishanth Menon @ 2023-10-27 11:22 UTC (permalink / raw) To: Nitin Yadav Cc: vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt, linux-arm-kernel, devicetree, linux-kernel On 15:09-20231027, Nitin Yadav wrote: > Add sdhci0 DT node in k3-am62a-main for eMMC support. Droping > ITAP values as they are NA in datasheet[0] for lower speed modes. > Add mmc0 alias for sdhci0 in k3-am62a7-sk.dts. > > [0]https://www.ti.com/lit/gpn/am62a3 Table: 7-79 (Page No. 179) > > Signed-off-by: Nitin Yadav <n-yadav@ti.com> > --- > arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 19 +++++++++++++++++++ > arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 1 + > 2 files changed, 20 insertions(+) > > diff --git a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi > index de36abb243f1..89b8b7d302cd 100644 > --- a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi > +++ b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi > @@ -488,6 +488,25 @@ main_gpio1: gpio@601000 { > status = "disabled"; > }; > > + sdhci0: mmc@fa10000 { > + compatible = "ti,am62-sdhci"; > + reg = <0x00 0xfa10000 0x00 0x260>, <0x00 0xfa18000 0x00 0x134>; > + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; > + power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>; > + clocks = <&k3_clks 57 5>, <&k3_clks 57 6>; > + clock-names = "clk_ahb", "clk_xin"; > + assigned-clocks = <&k3_clks 57 6>; > + assigned-clock-parents = <&k3_clks 57 8>; > + mmc-hs200-1_8v; > + ti,trm-icp = <0x2>; > + ti,otap-del-sel-legacy = <0x0>; > + ti,otap-del-sel-mmc-hs = <0x0>; > + ti,otap-del-sel-hs200 = <0x6>; > + bus-width = <8>; > + ti,clkbuf-sel = <0x7>; > + status = "disabled"; > + }; > + > sdhci1: mmc@fa00000 { > compatible = "ti,am62-sdhci"; > reg = <0x00 0xfa00000 0x00 0x260>, <0x00 0xfa08000 0x00 0x134>; > diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts > index cff283c75f8e..5d28c390b28e 100644 > --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts > +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts > @@ -20,6 +20,7 @@ aliases { > serial0 = &wkup_uart0; > serial2 = &main_uart0; > serial3 = &main_uart1; > + mmc0 = &sdhci0; Bring this in on your second patch in the series. > mmc1 = &sdhci1; > }; > > -- > 2.25.1 > -- Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 2/2] arm64: dts: ti: k3-am62a7-sk: Enable eMMC support 2023-10-27 9:39 [PATCH 0/2] Add eMMC support for AM62a SK Nitin Yadav 2023-10-27 9:39 ` [PATCH 1/2] arm64: dts: ti: k3-am62a-main: Add sdhci0 instance Nitin Yadav @ 2023-10-27 9:39 ` Nitin Yadav 2023-10-27 11:23 ` Nishanth Menon 1 sibling, 1 reply; 5+ messages in thread From: Nitin Yadav @ 2023-10-27 9:39 UTC (permalink / raw) To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt Cc: linux-arm-kernel, devicetree, linux-kernel Add support for 32GB eMMC card on AM62A7. Includes adding mmc0 pins settings and set sdhci0 status to okay. Signed-off-by: Nitin Yadav <n-yadav@ti.com> --- arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts index 5d28c390b28e..c6f144d91734 100644 --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts @@ -173,6 +173,22 @@ AM62AX_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */ >; }; + main_mmc0_pins_default: main-mmc0-default-pins { + pinctrl-single,pins = < + AM62AX_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */ + AM62AX_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLKLB */ + AM62AX_IOPAD(0x21c, PIN_INPUT, 0) /* (AB1) MMC0_CLK */ + AM62AX_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */ + AM62AX_IOPAD(0x210, PIN_INPUT_PULLUP, 0) /* (AA1) MMC0_DAT1 */ + AM62AX_IOPAD(0x20c, PIN_INPUT_PULLUP, 0) /* (AA3) MMC0_DAT2 */ + AM62AX_IOPAD(0x208, PIN_INPUT_PULLUP, 0) /* (Y4) MMC0_DAT3 */ + AM62AX_IOPAD(0x204, PIN_INPUT_PULLUP, 0) /* (AB2) MMC0_DAT4 */ + AM62AX_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (AC1) MMC0_DAT5 */ + AM62AX_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (AD2) MMC0_DAT6 */ + AM62AX_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */ + >; + }; + main_mmc1_pins_default: main-mmc1-default-pins { pinctrl-single,pins = < AM62AX_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */ @@ -362,3 +378,11 @@ cpsw3g_phy0: ethernet-phy@0 { ti,min-output-impedance; }; }; + +&sdhci0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_mmc0_pins_default>; + ti,driver-strength-ohm = <50>; + disable-wp; +}; -- 2.25.1 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 2/2] arm64: dts: ti: k3-am62a7-sk: Enable eMMC support 2023-10-27 9:39 ` [PATCH 2/2] arm64: dts: ti: k3-am62a7-sk: Enable eMMC support Nitin Yadav @ 2023-10-27 11:23 ` Nishanth Menon 0 siblings, 0 replies; 5+ messages in thread From: Nishanth Menon @ 2023-10-27 11:23 UTC (permalink / raw) To: Nitin Yadav Cc: vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt, linux-arm-kernel, devicetree, linux-kernel On 15:09-20231027, Nitin Yadav wrote: > Add support for 32GB eMMC card on AM62A7. Includes adding mmc0 > pins settings and set sdhci0 status to okay. You can drop the second sentence. Also, in this case, since you are modifying the board dts, it should be AM62A7 SK. > > Signed-off-by: Nitin Yadav <n-yadav@ti.com> > --- > arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 24 ++++++++++++++++++++++++ > 1 file changed, 24 insertions(+) > > diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts > index 5d28c390b28e..c6f144d91734 100644 > --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts > +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts > @@ -173,6 +173,22 @@ AM62AX_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */ > >; > }; > > + main_mmc0_pins_default: main-mmc0-default-pins { > + pinctrl-single,pins = < > + AM62AX_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */ > + AM62AX_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLKLB */ > + AM62AX_IOPAD(0x21c, PIN_INPUT, 0) /* (AB1) MMC0_CLK */ > + AM62AX_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */ > + AM62AX_IOPAD(0x210, PIN_INPUT_PULLUP, 0) /* (AA1) MMC0_DAT1 */ > + AM62AX_IOPAD(0x20c, PIN_INPUT_PULLUP, 0) /* (AA3) MMC0_DAT2 */ > + AM62AX_IOPAD(0x208, PIN_INPUT_PULLUP, 0) /* (Y4) MMC0_DAT3 */ > + AM62AX_IOPAD(0x204, PIN_INPUT_PULLUP, 0) /* (AB2) MMC0_DAT4 */ > + AM62AX_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (AC1) MMC0_DAT5 */ > + AM62AX_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (AD2) MMC0_DAT6 */ > + AM62AX_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */ > + >; > + }; > + > main_mmc1_pins_default: main-mmc1-default-pins { > pinctrl-single,pins = < > AM62AX_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */ > @@ -362,3 +378,11 @@ cpsw3g_phy0: ethernet-phy@0 { > ti,min-output-impedance; > }; > }; > + > +&sdhci0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_mmc0_pins_default>; > + ti,driver-strength-ohm = <50>; > + disable-wp; > +}; > -- > 2.25.1 > -- Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2023-10-27 11:23 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2023-10-27 9:39 [PATCH 0/2] Add eMMC support for AM62a SK Nitin Yadav 2023-10-27 9:39 ` [PATCH 1/2] arm64: dts: ti: k3-am62a-main: Add sdhci0 instance Nitin Yadav 2023-10-27 11:22 ` Nishanth Menon 2023-10-27 9:39 ` [PATCH 2/2] arm64: dts: ti: k3-am62a7-sk: Enable eMMC support Nitin Yadav 2023-10-27 11:23 ` Nishanth Menon
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).