[PATCH v6 0/2] backlight: mp3309c: Add support for MPS MP3309C

[PATCH v6 0/2] backlight: mp3309c: Add support for MPS MP3309C

[Flavio Suligoi]

This patchset (rebased on v6.7-rc1 kernel version):

- updates the mps,mp3309c.yaml dt bindings file:
    - Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml

- adds the related device driver to support the MPS MP3309C backlight chip.

Note: about the first point, the mps,mp3309c.yaml file updating, there are
      no compatibility problems with the previous version, since the
      related device driver has not yet been included in any kernel.
      Only this dt-binding yaml file is already included in the current
      v6.7-rc1 kernel version.
      No developer may have used it.

Flavio Suligoi (2):
  dt-bindings: backlight: mp3309c: remove two required properties
  backlight: mp3309c: Add support for MPS MP3309C

 .../bindings/leds/backlight/mps,mp3309c.yaml  |  10 +-
 MAINTAINERS                                   |   7 +
 drivers/video/backlight/Kconfig               |  11 +
 drivers/video/backlight/Makefile              |   1 +
 drivers/video/backlight/mp3309c.c             | 443 ++++++++++++++++++
 5 files changed, 466 insertions(+), 6 deletions(-)
 create mode 100644 drivers/video/backlight/mp3309c.c

-- 
2.34.1

[PATCH v6 1/2] dt-bindings: backlight: mp3309c: remove two required properties

[Flavio Suligoi]

The two properties:

- max-brightness
- default brightness

are not really required, so they can be removed from the "required"
section.
The "max-brightness" is no longer used in the current version
of the driver (it was used only in the first version).
The "default-brightness", if omitted in the DT, is managed by the
device driver, using a default value. This value depends on the dimming
mode used:

- for the "analog mode", via I2C commands, this value is fixed by
  hardware (=31)
- while in case of pwm mode the default used is the last value of the
  brightness-levels array.

Also the brightness-levels array is not required:

- in "analog mode", via I2C commands, the brightness-level array is
  fixed by hardware (0..31).;
- in pwm dimming mode, the driver uses a default array of 0..255 and
  the "default-brightness" is the last one, which is "255"

NOTE: there are no compatibility problems with the previous version,
      since the device driver has not yet been included in any kernel.
      Only this dt-binding yaml file is already included in the kernel
      repository.
      No developer may have used it.

Other changes:

- improve the backlight working mode description, in the "description"
  section
- update the example, removing the "max-brightness" and introducing the
  "brightess-levels" property

Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
---
 .../bindings/leds/backlight/mps,mp3309c.yaml           | 10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml b/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
index 4191e33626f5..527a37368ed7 100644
--- a/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
+++ b/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
@@ -14,8 +14,8 @@ description: |
   programmable switching frequency to optimize efficiency.
   It supports two different dimming modes:
 
-  - analog mode, via I2C commands (default)
-  - PWM controlled mode.
+  - analog mode, via I2C commands, as default mode (32 dimming levels)
+  - PWM controlled mode (optional)
 
   The datasheet is available at:
   https://www.monolithicpower.com/en/mp3309c.html
@@ -50,8 +50,6 @@ properties:
 required:
   - compatible
   - reg
-  - max-brightness
-  - default-brightness
 
 unevaluatedProperties: false
 
@@ -66,8 +64,8 @@ examples:
             compatible = "mps,mp3309c";
             reg = <0x17>;
             pwms = <&pwm1 0 3333333 0>; /* 300 Hz --> (1/f) * 1*10^9 */
-            max-brightness = <100>;
-            default-brightness = <80>;
+            brightness-levels = <0 4 8 16 32 64 128 255>;
+            default-brightness = <6>;
             mps,overvoltage-protection-microvolt = <24000000>;
         };
     };
-- 
2.34.1

[PATCH v6 2/2] backlight: mp3309c: Add support for MPS MP3309C

[Flavio Suligoi]

The Monolithic Power (MPS) MP3309C is a WLED step-up converter, featuring a
programmable switching frequency to optimize efficiency.
The brightness can be controlled either by I2C commands (called "analog"
mode) or by a PWM input signal (PWM mode).
This driver supports both modes.

For DT configuration details, please refer to:
- Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml

The datasheet is available at:
- https://www.monolithicpower.com/en/mp3309c.html

Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
---
 MAINTAINERS                       |   7 +
 drivers/video/backlight/Kconfig   |  11 +
 drivers/video/backlight/Makefile  |   1 +
 drivers/video/backlight/mp3309c.c | 443 ++++++++++++++++++++++++++++++
 4 files changed, 462 insertions(+)
 create mode 100644 drivers/video/backlight/mp3309c.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 5c9f868e13b6..d033c2a2d120 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14657,6 +14657,13 @@ S:	Maintained
 F:	Documentation/driver-api/tty/moxa-smartio.rst
 F:	drivers/tty/mxser.*
 
+MP3309C BACKLIGHT DRIVER
+M:	Flavio Suligoi <f.suligoi@asem.it>
+L:	dri-devel@lists.freedesktop.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
+F:	drivers/video/backlight/mp3309c.c
+
 MR800 AVERMEDIA USB FM RADIO DRIVER
 M:	Alexey Klimov <klimov.linux@gmail.com>
 L:	linux-media@vger.kernel.org
diff --git a/drivers/video/backlight/Kconfig b/drivers/video/backlight/Kconfig
index 51387b1ef012..1144a54a35c0 100644
--- a/drivers/video/backlight/Kconfig
+++ b/drivers/video/backlight/Kconfig
@@ -402,6 +402,17 @@ config BACKLIGHT_LP8788
 	help
 	  This supports TI LP8788 backlight driver.
 
+config BACKLIGHT_MP3309C
+	tristate "Backlight Driver for MPS MP3309C"
+	depends on I2C && PWM
+	select REGMAP_I2C
+	help
+	  This supports MPS MP3309C backlight WLED driver in both PWM and
+	  analog/I2C dimming modes.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called mp3309c.
+
 config BACKLIGHT_PANDORA
 	tristate "Backlight driver for Pandora console"
 	depends on TWL4030_CORE
diff --git a/drivers/video/backlight/Makefile b/drivers/video/backlight/Makefile
index f72e1c3c59e9..1af583de665b 100644
--- a/drivers/video/backlight/Makefile
+++ b/drivers/video/backlight/Makefile
@@ -44,6 +44,7 @@ obj-$(CONFIG_BACKLIGHT_LP855X)		+= lp855x_bl.o
 obj-$(CONFIG_BACKLIGHT_LP8788)		+= lp8788_bl.o
 obj-$(CONFIG_BACKLIGHT_LV5207LP)	+= lv5207lp.o
 obj-$(CONFIG_BACKLIGHT_MAX8925)		+= max8925_bl.o
+obj-$(CONFIG_BACKLIGHT_MP3309C)		+= mp3309c.o
 obj-$(CONFIG_BACKLIGHT_MT6370)		+= mt6370-backlight.o
 obj-$(CONFIG_BACKLIGHT_OMAP1)		+= omap1_bl.o
 obj-$(CONFIG_BACKLIGHT_PANDORA)		+= pandora_bl.o
diff --git a/drivers/video/backlight/mp3309c.c b/drivers/video/backlight/mp3309c.c
new file mode 100644
index 000000000000..3fe4469ef43f
--- /dev/null
+++ b/drivers/video/backlight/mp3309c.c
@@ -0,0 +1,443 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Driver for MPS MP3309C White LED driver with I2C interface
+ *
+ * This driver support both analog (by I2C commands) and PWM dimming control
+ * modes.
+ *
+ * Copyright (C) 2023 ASEM Srl
+ * Author: Flavio Suligoi <f.suligoi@asem.it>
+ *
+ * Based on pwm_bl.c
+ */
+
+#include <linux/backlight.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/pwm.h>
+#include <linux/regmap.h>
+
+#define REG_I2C_0	0x00
+#define REG_I2C_1	0x01
+
+#define REG_I2C_0_EN	0x80
+#define REG_I2C_0_D0	0x40
+#define REG_I2C_0_D1	0x20
+#define REG_I2C_0_D2	0x10
+#define REG_I2C_0_D3	0x08
+#define REG_I2C_0_D4	0x04
+#define REG_I2C_0_RSRV1	0x02
+#define REG_I2C_0_RSRV2	0x01
+
+#define REG_I2C_1_RSRV1	0x80
+#define REG_I2C_1_DIMS	0x40
+#define REG_I2C_1_SYNC	0x20
+#define REG_I2C_1_OVP0	0x10
+#define REG_I2C_1_OVP1	0x08
+#define REG_I2C_1_VOS	0x04
+#define REG_I2C_1_LEDO	0x02
+#define REG_I2C_1_OTP	0x01
+
+#define ANALOG_I2C_NUM_LEVELS	32		/* 0..31 */
+#define ANALOG_I2C_REG_MASK	0x7c
+
+#define MP3309C_PWM_DEFAULT_NUM_LEVELS	256	/* 0..255 */
+
+enum mp3309c_status_value {
+	FIRST_POWER_ON,
+	BACKLIGHT_OFF,
+	BACKLIGHT_ON,
+};
+
+enum mp3309c_dimming_mode_value {
+	DIMMING_PWM,
+	DIMMING_ANALOG_I2C,
+};
+
+struct mp3309c_platform_data {
+	unsigned int max_brightness;
+	unsigned int default_brightness;
+	unsigned int *levels;
+	u8  dimming_mode;
+	u8  over_voltage_protection;
+	bool sync_mode;
+	u8 status;
+};
+
+struct mp3309c_chip {
+	struct device *dev;
+	struct mp3309c_platform_data *pdata;
+	struct backlight_device *bl;
+	struct gpio_desc *enable_gpio;
+	struct regmap *regmap;
+	struct pwm_device *pwmd;
+};
+
+static const struct regmap_config mp3309c_regmap = {
+	.name = "mp3309c_regmap",
+	.reg_bits = 8,
+	.reg_stride = 1,
+	.val_bits = 8,
+	.max_register = REG_I2C_1,
+};
+
+static int mp3309c_enable_device(struct mp3309c_chip *chip)
+{
+	u8 reg_val;
+	int ret;
+
+	/* I2C register #0 - Device enable */
+	ret = regmap_update_bits(chip->regmap, REG_I2C_0, REG_I2C_0_EN,
+				 REG_I2C_0_EN);
+	if (ret)
+		return ret;
+
+	/*
+	 * I2C register #1 - Set working mode:
+	 *  - set one of the two dimming mode:
+	 *    - PWM dimming using an external PWM dimming signal
+	 *    - analog dimming using I2C commands
+	 *  - enable/disable synchronous mode
+	 *  - set overvoltage protection (OVP)
+	 */
+	reg_val = 0x00;
+	if (chip->pdata->dimming_mode == DIMMING_PWM)
+		reg_val |= REG_I2C_1_DIMS;
+	if (chip->pdata->sync_mode)
+		reg_val |= REG_I2C_1_SYNC;
+	reg_val |= chip->pdata->over_voltage_protection;
+	ret = regmap_write(chip->regmap, REG_I2C_1, reg_val);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int mp3309c_bl_update_status(struct backlight_device *bl)
+{
+	struct mp3309c_chip *chip = bl_get_data(bl);
+	int brightness = backlight_get_brightness(bl);
+	struct pwm_state pwmstate;
+	unsigned int analog_val, bits_val;
+	int i, ret;
+
+	if (chip->pdata->dimming_mode == DIMMING_PWM) {
+		/*
+		 * PWM control mode
+		 */
+		pwm_get_state(chip->pwmd, &pwmstate);
+		pwm_set_relative_duty_cycle(&pwmstate,
+					    chip->pdata->levels[brightness],
+					    chip->pdata->levels[chip->pdata->max_brightness]);
+		pwmstate.enabled = true;
+		ret = pwm_apply_state(chip->pwmd, &pwmstate);
+		if (ret)
+			return ret;
+
+		switch (chip->pdata->status) {
+		case FIRST_POWER_ON:
+		case BACKLIGHT_OFF:
+			/*
+			 * After 20ms of low pwm signal level, the chip turns
+			 * off automatically. In this case, before enabling the
+			 * chip again, we must wait about 10ms for pwm signal to
+			 * stabilize.
+			 */
+			if (brightness > 0) {
+				msleep(10);
+				mp3309c_enable_device(chip);
+				chip->pdata->status = BACKLIGHT_ON;
+			} else {
+				chip->pdata->status = BACKLIGHT_OFF;
+			}
+			break;
+		case BACKLIGHT_ON:
+			if (brightness == 0)
+				chip->pdata->status = BACKLIGHT_OFF;
+			break;
+		}
+	} else {
+		/*
+		 * Analog (by I2C command) control mode
+		 *
+		 * The first time, before setting brightness, we must enable the
+		 * device
+		 */
+		if (chip->pdata->status == FIRST_POWER_ON)
+			mp3309c_enable_device(chip);
+
+		/*
+		 * Dimming mode I2C command (fixed dimming range 0..31)
+		 *
+		 * The 5 bits of the dimming analog value D4..D0 is allocated
+		 * in the I2C register #0, in the following way:
+		 *
+		 *     +--+--+--+--+--+--+--+--+
+		 *     |EN|D0|D1|D2|D3|D4|XX|XX|
+		 *     +--+--+--+--+--+--+--+--+
+		 */
+		analog_val = brightness;
+		bits_val = 0;
+		for (i = 0; i <= 5; i++)
+			bits_val += ((analog_val >> i) & 0x01) << (6 - i);
+		ret = regmap_update_bits(chip->regmap, REG_I2C_0,
+					 ANALOG_I2C_REG_MASK, bits_val);
+		if (ret)
+			return ret;
+
+		if (brightness > 0)
+			chip->pdata->status = BACKLIGHT_ON;
+		else
+			chip->pdata->status = BACKLIGHT_OFF;
+	}
+
+	return 0;
+}
+
+static const struct backlight_ops mp3309c_bl_ops = {
+	.update_status = mp3309c_bl_update_status,
+};
+
+static int pm3309c_parse_dt_node(struct mp3309c_chip *chip,
+				 struct mp3309c_platform_data *pdata)
+{
+	struct device_node *node = chip->dev->of_node;
+	struct property *prop_pwms, *prop_levels;
+	int length = 0;
+	int ret, i;
+	unsigned int num_levels, tmp_value;
+
+	if (!node) {
+		dev_err(chip->dev, "failed to get DT node\n");
+		return -ENODEV;
+	}
+
+	/*
+	 * Dimming mode: the MP3309C provides two dimming control mode:
+	 *
+	 * - PWM mode
+	 * - Analog by I2C control mode (default)
+	 *
+	 * I2C control mode is assumed as default but, if the pwms property is
+	 * found in the backlight node, the mode switches to PWM mode.
+	 */
+	pdata->dimming_mode = DIMMING_ANALOG_I2C;
+	prop_pwms = of_find_property(node, "pwms", &length);
+	if (prop_pwms) {
+		chip->pwmd = devm_pwm_get(chip->dev, NULL);
+		if (IS_ERR(chip->pwmd))
+			return dev_err_probe(chip->dev, PTR_ERR(chip->pwmd),
+					     "error getting pwm data\n");
+		pdata->dimming_mode = DIMMING_PWM;
+		pwm_apply_args(chip->pwmd);
+	}
+
+	/*
+	 * In I2C control mode the dimming levels (0..31) are fixed by the
+	 * hardware, while in PWM control mode they can be chosen by the user,
+	 * to allow nonlinear mappings.
+	 */
+	if  (pdata->dimming_mode == DIMMING_ANALOG_I2C) {
+		/*
+		 * Analog (by I2C commands) control mode: fixed 0..31 brightness
+		 * levels
+		 */
+		num_levels = ANALOG_I2C_NUM_LEVELS;
+
+		/* Enable GPIO used in I2C dimming mode only */
+		chip->enable_gpio = devm_gpiod_get(chip->dev, "enable",
+						   GPIOD_OUT_HIGH);
+		if (IS_ERR(chip->enable_gpio))
+			return dev_err_probe(chip->dev,
+					     PTR_ERR(chip->enable_gpio),
+					     "error getting enable gpio\n");
+	} else {
+		/*
+		 * PWM control mode: check for brightness level in DT
+		 */
+		prop_levels = of_find_property(node, "brightness-levels",
+					       &length);
+		if (prop_levels) {
+			/* Read brightness levels from DT */
+			num_levels = length / sizeof(u32);
+			if (num_levels < 2)
+				return -EINVAL;
+		} else {
+			/* Use default brightness levels */
+			num_levels = MP3309C_PWM_DEFAULT_NUM_LEVELS;
+		}
+	}
+
+	/* Fill brightness levels array */
+	pdata->levels = devm_kcalloc(chip->dev, num_levels,
+				     sizeof(*pdata->levels), GFP_KERNEL);
+	if (!pdata->levels)
+		return -ENOMEM;
+	if (prop_levels) {
+		ret = of_property_read_u32_array(node, "brightness-levels",
+						 pdata->levels,
+						 num_levels);
+		if (ret < 0)
+			return ret;
+	} else {
+		for (i = 0; i < num_levels; i++)
+			pdata->levels[i] = i;
+	}
+
+	pdata->max_brightness = num_levels - 1;
+
+	ret = of_property_read_u32(node, "default-brightness",
+				   &pdata->default_brightness);
+	if (ret)
+		pdata->default_brightness = pdata->max_brightness;
+	if (pdata->default_brightness > pdata->max_brightness) {
+		dev_err(chip->dev,
+			"default brightness exceeds max brightness\n");
+		pdata->default_brightness = pdata->max_brightness;
+	}
+
+	/*
+	 * Over-voltage protection (OVP)
+	 *
+	 * This (optional) property values are:
+	 *
+	 *  - 13.5V
+	 *  - 24V
+	 *  - 35.5V (hardware default setting)
+	 *
+	 * If missing, the default value for OVP is 35.5V
+	 */
+	pdata->over_voltage_protection = REG_I2C_1_OVP1;
+	if (!of_property_read_u32(node, "mps,overvoltage-protection-microvolt",
+				  &tmp_value)) {
+		switch (tmp_value) {
+		case 13500000:
+			pdata->over_voltage_protection = 0x00;
+			break;
+		case 24000000:
+			pdata->over_voltage_protection = REG_I2C_1_OVP0;
+			break;
+		case 35500000:
+			pdata->over_voltage_protection = REG_I2C_1_OVP1;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	/* Synchronous (default) and non-synchronous mode */
+	pdata->sync_mode = true;
+	if (of_property_read_bool(node, "mps,no-sync-mode"))
+		pdata->sync_mode = false;
+
+	return 0;
+}
+
+static int mp3309c_probe(struct i2c_client *client)
+{
+	struct mp3309c_platform_data *pdata = dev_get_platdata(&client->dev);
+	struct mp3309c_chip *chip;
+	struct backlight_properties props;
+	struct pwm_state pwmstate;
+	int ret;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		dev_err(&client->dev, "failed to check i2c functionality\n");
+		return -EOPNOTSUPP;
+	}
+
+	chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->dev = &client->dev;
+
+	chip->regmap = devm_regmap_init_i2c(client, &mp3309c_regmap);
+	if (IS_ERR(chip->regmap))
+		return dev_err_probe(&client->dev, PTR_ERR(chip->regmap),
+				     "failed to allocate register map\n");
+
+	i2c_set_clientdata(client, chip);
+
+	if (!pdata) {
+		pdata = devm_kzalloc(chip->dev, sizeof(*pdata), GFP_KERNEL);
+		if (!pdata)
+			return -ENOMEM;
+
+		ret = pm3309c_parse_dt_node(chip, pdata);
+		if (ret)
+			return ret;
+	}
+	chip->pdata = pdata;
+
+	/* Backlight properties */
+	props.brightness = pdata->default_brightness;
+	props.max_brightness = pdata->max_brightness;
+	props.scale = BACKLIGHT_SCALE_LINEAR;
+	props.type = BACKLIGHT_RAW;
+	props.power = FB_BLANK_UNBLANK;
+	props.fb_blank = FB_BLANK_UNBLANK;
+	chip->bl = devm_backlight_device_register(chip->dev, "mp3309c",
+						  chip->dev, chip,
+						  &mp3309c_bl_ops, &props);
+	if (IS_ERR(chip->bl))
+		return dev_err_probe(chip->dev, PTR_ERR(chip->bl),
+				     "error registering backlight device\n");
+
+	/* In PWM dimming mode, enable pwm device */
+	if (chip->pdata->dimming_mode == DIMMING_PWM) {
+		pwm_init_state(chip->pwmd, &pwmstate);
+		pwm_set_relative_duty_cycle(&pwmstate,
+					    chip->pdata->default_brightness,
+					    chip->pdata->max_brightness);
+		pwmstate.enabled = true;
+		ret = pwm_apply_state(chip->pwmd, &pwmstate);
+		if (ret)
+			return dev_err_probe(chip->dev, ret,
+					     "error setting pwm device\n");
+	}
+
+	chip->pdata->status = FIRST_POWER_ON;
+	backlight_update_status(chip->bl);
+
+	return 0;
+}
+
+static void mp3309c_remove(struct i2c_client *client)
+{
+	struct mp3309c_chip *chip = i2c_get_clientdata(client);
+	struct backlight_device *bl = chip->bl;
+
+	bl->props.power = FB_BLANK_POWERDOWN;
+	bl->props.brightness = 0;
+	backlight_update_status(chip->bl);
+}
+
+static const struct of_device_id mp3309c_match_table[] = {
+	{ .compatible = "mps,mp3309c", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mp3309c_match_table);
+
+static const struct i2c_device_id mp3309c_id[] = {
+	{ "mp3309c", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, mp3309c_id);
+
+static struct i2c_driver mp3309c_i2c_driver = {
+	.driver	= {
+			.name		= KBUILD_MODNAME,
+			.of_match_table	= mp3309c_match_table,
+	},
+	.probe		= mp3309c_probe,
+	.remove		= mp3309c_remove,
+	.id_table	= mp3309c_id,
+};
+
+module_i2c_driver(mp3309c_i2c_driver);
+
+MODULE_DESCRIPTION("Backlight Driver for MPS MP3309C");
+MODULE_AUTHOR("Flavio Suligoi <f.suligoi@asem.it>");
+MODULE_LICENSE("GPL");
-- 
2.34.1

Re: [PATCH v6 1/2] dt-bindings: backlight: mp3309c: remove two required properties

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 241 bytes --]

On Wed, Nov 15, 2023 at 04:29:01PM +0100, Flavio Suligoi wrote:
> Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>

You omitted my ack that I gave on the previous version.
Acked-by: Conor Dooley <conor.dooley@microchip.com>

Cheers,
Conor.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]