Re: [PATCH v2 1/2] dt-bindings: iio: pressure: add honeywell,hsc030

[Jonathan Cameron <Jonathan.Cameron@Huawei.com>]

On Mon, 20 Nov 2023 16:40:51 +0200
Petre Rodan <petre.rodan@subdimension.ro> wrote:

> Hello!
> 
> On Mon, Nov 20, 2023 at 03:04:07PM +0100, Krzysztof Kozlowski wrote:
> > On 20/11/2023 14:42, Petre Rodan wrote:
> >   
> > >>> +properties:
> > >>> +  compatible:
> > >>> +    enum:
> > >>> +      - honeywell,hsc  
> > >>
> > >> Way too generic  
> > > 
> > > I'm new to this, please excuse my ignorance.
> > > my driver covers all Honeywell pressure sensors under the "TruStability board mount HSC/SSC" moniker.  
> > 
> > We talk here about bindings, not driver. For the driver you can use
> > whatever name is approved by reviewers of your driver.
> >   
> > > that is why my intention was to provide a rather generic name for the driver itself.
> > > are you afraid that they will come up with a different device that they will call "hsc" in the future?
> > > in this case honeywell,trustability-hsc would be fine?
> > > 
> > > as I see you prefer to target a particular chip, but I am a bit afraid that the end-user will be confused by needing to set up something like
> > > 
> > > pressure@28 {
> > > 	compatible = "honeywell,hsc030pa";  
> > 
> > The compatible should be specific, thus for example match exact model
> > number.  
> 
> there are an infinite number of combinations of 4 transfer functions and 118 ranges + one custom range, so providing an array with all specific chips that could end up as compatible is out of the question.
> I was aiming at providing a generic name for the binding and get the transfer function and the pressure range as required parameters.
> 
> > If you can guarantee that all devices from given family are the same in
> > respect of programming model and hardware requirements (e.g. supplies),
> > then you could go with family name. However such guarantees are rarely
> > given.  
> 
> I see your point.
> 
> > Therefore for mprls0025pa I agreed for using one specific model
> > for entire family.
> > 
> > https://lore.kernel.org/all/d577bc44-780f-f25d-29c6-ed1d353b540c@linaro.org/
> > 
> >   
> > > 	reg = <0x28>;
> > > 	honeywell,transfer-function = <0>;
> > > 	honeywell,pressure-range = "250MD";
> > > };
> > > 
> > > ie. specifying "hsc030pa" as driver while his chip is not in the 030PA range, but 250MD.
> > > 
> > > so do you prefer
> > >  honeywell,trustability-hsc  OR
> > >  honeywell,hsc030pa  
> > 
> > I think the latter, just like we did for mprls0025pa. How many devices
> > do you have there?  
> 
> both hsc and ssc have 118 ranges, 4 transfer functions and both can be requested from the manufacturer with custom measurement ranges.
> 
> ok,I will rename hsc->hsc030pa in the code as you requested.

Where does pa come from? 

If we are going generic, feels like trustability-ssc etc are more representative
and matches the datasheet cover page.


> 
> > >>> +  honeywell,pmin-pascal:
> > >>> +    description: |
> > >>> +      Minimum pressure value the sensor can measure in pascal.
> > >>> +      To be specified only if honeywell,range_str is set to "NA".
> > >>> +    $ref: /schemas/types.yaml#/definitions/int32  
> > >>
> > >> That's uint32. Why do you need negative values?  
> > > 
> > > signed int32 is intentional. some chips have two physical input ports and measure a pressure differential in which case pmin is negative.
> > > see either of the pdfs at page 14, table 8, column 2, row 7+  
> > 
> > Then the best would be to change the type in other bindings to have
> > int32 everywhere... but dtschema also requires unt32:
> > https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/property-units.yaml  
> 
> yeah, and also '-kpascal' might be too coarse of a unit when we talk about sensors that have a -125 .. 125 pascal measurement range as '0.5ND' has.
> 
> cheers,
> peter
>