[PATCH v3 8/8] arm64: dts: qcom: sm8650-qrd: add interconnect dependent device nodes

[Neil Armstrong <neil.armstrong@linaro.org>]

Now interconnect dependent devices are added in sm8650 DTSI,
now enable more devices for the Qualcomm SM8650 QRD board:
- PCIe
- Display
- DSPs
- SDCard
- UFS
- USB role switch with PMIC Glink
- Bluetooth

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8650-qrd.dts | 275 +++++++++++++++++++++++++++++++-
 1 file changed, 274 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
index f5ce4c889680..b41f90d817bb 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
@@ -23,6 +23,7 @@ / {
 
 	aliases {
 		serial0 = &uart15;
+		serial1 = &uart14;
 	};
 
 	chosen {
@@ -45,6 +46,44 @@ key-volume-up {
 		};
 	};
 
+	pmic-glink {
+		compatible = "qcom,sm8650-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_ss>;
+					};
+				};
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 
@@ -399,6 +438,81 @@ vreg_l3i_1p2: ldo3 {
 	};
 };
 
+&dispcc {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l3i_1p2>;
+
+	status = "okay";
+
+	panel@0 {
+		compatible = "visionox,vtdr6130";
+		reg = <0>;
+
+		reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+		vddio-supply = <&vreg_l12b_1p8>;
+		vci-supply = <&vreg_l13b_3p0>;
+		vdd-supply = <&vreg_l11b_1p2>;
+
+		pinctrl-0 = <&disp0_resetn_active>, <&mdp_vsync_active>;
+		pinctrl-1 = <&disp0_resetn_suspend>, <&mdp_vsync_suspend>;
+		pinctrl-names = "default", "sleep";
+
+		port {
+			panel0_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel0_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l1i_0p88>;
+
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
+&pcie_1_phy_aux_clk {
+	clock-frequency = <1000>;
+};
+
+&pcie0 {
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1i_0p88>;
+	vdda-pll-supply = <&vreg_l3i_1p2>;
+
+	status = "okay";
+};
+
 &pon_pwrkey {
 	status = "okay";
 };
@@ -479,22 +593,172 @@ &pmk8550_rtc {
 	status = "okay";
 };
 
+&qupv3_id_0 {
+	status = "okay";
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
 
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8650/adsp.mbn",
+			"qcom/sm8650/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/sm8650/cdsp.mbn",
+			"qcom/sm8650/cdsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_mpss {
+	firmware-name = "qcom/sm8650/modem.mbn",
+			"qcom/sm8650/modem_dtb.mbn";
+
+	status = "okay";
+};
+
 &sleep_clk {
 	clock-frequency = <32000>;
 };
 
+&spi4 {
+	status = "okay";
+
+	touchscreen@0 {
+		compatible = "goodix,gt9916";
+		reg = <0>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <162 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&tlmm 161 GPIO_ACTIVE_LOW>;
+
+		avdd-supply = <&vreg_l14b_3p2>;
+
+		spi-max-frequency = <1000000>;
+
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <2400>;
+
+		pinctrl-0 = <&ts_irq>, <&ts_reset>;
+		pinctrl-names = "default";
+	};
+};
+
 &tlmm {
 	gpio-reserved-ranges = <32 8>;
+
+	bt_default: bt-default-state {
+		bt-en-pins {
+			pins = "gpio17";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		sw-ctrl-pins {
+			pins = "gpio18";
+			function = "gpio";
+			bias-pull-down;
+		};
+	};
+
+	disp0_resetn_active: disp0-resetn-active-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	disp0_resetn_suspend: disp0-resetn-suspend-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdp_vsync_active: mdp-vsync-active-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdp_vsync_suspend: mdp-vsync-suspend-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	ts_irq: ts-irq-state {
+		pins = "gpio161";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+		output-disable;
+	};
+
+	ts_reset: ts-reset-state {
+		pins = "gpio162";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+
+		clocks = <&rpmhcc RPMH_RF_CLK1>;
+
+		vddio-supply = <&vreg_l3c_1p2>;
+		vddaon-supply = <&vreg_l15b_1p8>;
+		vdddig-supply = <&vreg_s3c_0p9>;
+		vddrfa0p8-supply = <&vreg_s3c_0p9>;
+		vddrfa1p2-supply = <&vreg_s1c_1p2>;
+		vddrfa1p9-supply = <&vreg_s6c_1p8>;
+
+		max-speed = <3200000>;
+
+		enable-gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>;
+		swctrl-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&bt_default>;
+		pinctrl-names = "default";
+	};
 };
 
 &uart15 {
 	status = "okay";
 };
 
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l17b_2p5>;
+	vcc-max-microamp = <1300000>;
+	vccq-supply = <&vreg_l1c_1p2>;
+	vccq-max-microamp = <1200000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l1d_0p88>;
+	vdda-pll-supply = <&vreg_l3i_1p2>;
+
+	status = "okay";
+};
+
 /*
  * DPAUX -> WCD9395 -> USB_SBU -> USB-C
  * eUSB2 DP/DM -> PM85550HS -> eUSB2 DP/DM -> WCD9395 -> USB-C
@@ -506,7 +770,16 @@ &usb_1 {
 };
 
 &usb_1_dwc3 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+	remote-endpoint = <&pmic_glink_ss_in>;
 };
 
 &usb_1_hsphy {

-- 
2.34.1